2018 Hyundai Ioniq Hybrid TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

in the related shop manual, Motor Control System, refer to the shop manual for diagnosis. If the diagnosis indicates a faulty hybrid drive motor, refer to the Service Procedure and replace the hybrid drive motor.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

Coolant thermostat - Coolant temp Below thermostat regulating Temperature. There is no drivability issue with this DTC.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Evaporative System (EVAP) - Very Small Leak This bulletin provides instructions to install an Air Filter Kit and a Natural Vacuum Leak Detection sensor (NVLD).

as separate components.

Evaporative System (EVAP) - Very Small LeakThese conditions primarily occur in the California coastal areas that are subject to marine layer cloud cover. Salt particulate deposit can form inside the Natural Vacuum Leak Detection (NVLD) which may cause intermittent operation prompting the DTC P0456 and the check engine light ?ON?. This bulletin provides the procedure to install a new Air Filter Kit with an updated filter to help prevent entry of the salt particulates. In addition, vehicles with check engine light ?ON? and DTC P0456 found stored in the Engine Control Module (ECM) must also replace the NVLD part.

System (EVAP) - Very Small LeakThese conditions primarily occur in the California coastal areas that are subject to marine layer cloud cover. Salt particulate deposit can form inside the Natural Vacuum Leak Detection (NVLD) which may cause intermittent operation prompting the DTC P0456 and the check engine light ON. This bulletin provides the procedure to install a new Air Filter Kit with an updated filter to help prevent entry of the salt particulates. In addition, vehicles with check engine light ON and DTC P0456 found stored in the Engine Control Module (ECM) must also replace the NVLD part."

as separate components.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

Service Campaign T3D provides a procedure to update the BMS ECU software.

This TSB# 21-01-080H describes the 3-part software to correct this condition and activate Blue Link Services.

This bulletin describes the 3-part Software to correct this condition and activate Blue Link Services.

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Intl. (KBI).

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Inc. (KBI).

below are replaced or the DTC listed are stored.

actuator malfunction, which may cause: The charging connector to not remain locked when the charger is inserted into the charging port. And/or the charging connector to be unable removed from the vehicle charging port. This bulletin provides part replacement instruction and information on the availability of the inlet locking actuator as a separate part. If the vehicle exhibits one of the condition described above, it is recommended to replace the inlet locking actuator only, not the entire quick charge inlet cable wiring assembly.

LiOn battery system management and diagnostics.

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Inc. (KBI).

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

clock or view it on the top of the screen.

system frequently losing a Bluetooth connection with Apple iPhone devices.

the inability to set the clock or view it on the top of the screen.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This procedure applies when any air is introduced into the Active Hydraulic Boost (AHB) system, which consists of the pressure supply unit (PSU), and the integrated brake actuation unit (IBAU). Improper bleeding of the brake system can result in the presence of air, which may reduce braking effectiveness.

This bulletin provides information of how to diagnose the no charging condition.

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

exhibits Diagnostic Trouble Code (DTC) C120B/D or C160A.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

OEM (new) and remanufactured automatic transmissions:

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.

compressors equipped in hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles.

compressors equipped in hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles.

P0456 on certain 2017-2019 Ioniq (AE) HEV vehicles.

P0456 on certain 2017-2019 Ioniq (AE) HEV vehicles.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.