2024 Hyundai Ioniq 5 TSBs

display warning messages on the instrument cluster, resulting in the PDW sensor(s) failing to detect nearby objects or triggering multiple false alarms. This condition may be a result of external damage to the PDW sensor membrane or sensor cover from rock chips or road debris, a collision, or previous vehicle repairs or modifications.

This may be caused by the lower cover becoming loose around the center mounting bolts. Follow the procedure in this bulletin to replace the mounting bolts and install cup washers with each bolt to hold the cover in place and resolve the noise on affected vehicles.

require a replacement of the Integrated Charging Control Unit (ICCU) and ICCU Fuse. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the Integrated Charging Control Unit (ICCU) and ICCU Fuse Replacement has been extended to 15 years/ 180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in Technical Service Bulletin (TSB) 26-BE-010H to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement. Please note that any vehicles under 15 years/180,000 miles are covered by this TSB, even if vehicle is within High Voltage Warranty of 10 years/120,000 miles.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in this bulletin to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement.

the 12V battery voltage drops below the operational voltage and the Vehicle Control Unit (VCU) places the vehicle in fail-safe mode. The VCU software in this bulletin updates the maximum vehicle speeds for various levels of 12V battery voltage when the vehicle enters fail-safe mode.

require an Integrated Charge Control Unit (ICCU) replacement, such as required for DTC P1A9096 DC to DC related charging concern or for inoperative AC charging. The ICCU fuse accessible from a rear side panel of the EV Battery, should NEVER be replaced by itself prior to receiving an ICCU replacement part. The ICCU fuse should be replaced at the same time as replacing the ICCU part. o The ICCU fuse function is to protect the EV Battery from a damaged ICCU. o DTC P1B77 Power Relay Assy (PRA) damage in the EV Battery can occur when an ICCU fuse is first replaced without also replacing the ICCU together. o Vehicles with P1B77 require Techline approval for field staff involved EV Battery repair and can result in significant additional delay for customers. o Wait to receive ICCU replacement part first before also replacing the ICCU fuse on the rear side of the EV battery. This bulletin also covers how to handle a situation when the nut(s) at the rear of the ICCU fuse falls back into the battery.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

This bulletin provides instructions to perform a dealer mode factory reset, followed by a head unit reset for vehicles experiencing the concerns.

symbol) with "Power is limited" displayed in the cluster, and possible DTC P0A2F. If you are servicing a vehicle with either of these conditions, follow this bulletin to inspect the EOP.

This bulletin provides instructions to perform a dealer mode factory reset, followed by a head unit reset for vehicles experiencing the concerns.

This bulletin provides instructions to perform a dealer mode factory reset, followed by a head unit reset for vehicles experiencing the concerns.

This bulletin provides instructions to adjust the gap between the tailgate and vehicle body to eliminate the rattle and friction noise.

experience excessive rear gap within the charging door.

This bulletin provides instructions to adjust the gap between the tailgate and vehicle body to eliminate the rattle and friction noise.

The leakage may contaminate other parts inside or outside of the TMK bag. Follow the procedure in this bulletin to determine if the sealant is leaking and, if necessary, replace any parts that have been contaminated. If the sealant has not leaked, replace only the TMK Sealant Cap.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

Gear System, also known as Motor-Gear Driven Unit (MGDU), that may have received an incorrect amount of oil/fluid during manufacturing. In some cases, the motor and/or reduction gear can produce a grinding/whining noise during operation. Follow the procedures in this bulletin to drain the existing oil and replace it with new oil to resolve this condition.

insulation caps (DC pin caps) which may lead to damage to the charge port if not replaced. This bulletin provides instructions to replace the DC pin cap(s).

a condition while charging with a 240V AC (Level 2) charger where the vehicle experiences an interrupted charging session or a lower charging speed. This occurs to prevent potential damage to the charging cable connection. Follow the procedure in this TSB to update the software logic for the Vehicle Charging Management System (VCMS), which initiates a self-restart that allows the vehicle charging to return to full capacity once stabilized.

240V AC (Level 2) charger where the vehicle experiences an interrupted charging session or a lower charging speed. This occurs to prevent potential damage to the charging cable connection. Follow the procedure in this TSB to update the software logic for the Vehicle Charging Management System (VCMS), which initiates a self-restart that allows the vehicle charging to return to full capacity once stabilized.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.