2022 Hyundai Elantra TSBs

a warning lamp for DTC P218100 (Cooling System Performance) related to the Integrated Thermal-Management Module (ITM). Follow the service procedure in this bulletin to install a spring onto the thermostat within the ITM, in order to prevent premature opening, and perform an ECU software update on affected vehicles.

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

tank assembly at idle or on an incline when the PCSV (Purge Control Solenoid Valve) is operating, and fuel level is above 90% full. If the noise is heard, follow the service procedure to replace the fuel tank assembly and resolve the concern.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

(CN7) and 2022-2023MY Kona (OS) vehicles equipped with the 1.6 liter T-GDI Gamma 2 engine, that may exhibit a warning lamp with one or more of the DTCs listed below: P250F - Engine Oil Level Too Low P011B, P050C - Engine Coolant Temperature/intake Air Temperature Correlation P00B7, P2B60 - Engine Coolant Flow Low/Performance

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

malfunction indicator light due to Diagnostic Trouble Codes (DTC) listed below. This bulletin provides information on replacing the oil pressure sensor to remedy these DTCs, rather than replacing the entire IVT assembly.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

follow the repair procedure and perform the diagnosis. If necessary, replace the High Flow electric oil pump (HF EOP) for HF EOP issues or the Dual Clutch Transmission for High Pressure electric oil pump (HP EOP) issues.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

machining burrs at the mounting port of the cylinder head, resulting in improper coolant sealing.

may experience an inoperable horn. Hyundai is extending the warranty coverage for the Horn Assembly under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owner.

may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

vehicles may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this TSB to install the latest design.

equipped with two (2) complete Smart Key FOBs were delivered with only one (1) complete Smart Key FOB and one additional mechanical key. A second Smart Key FOB can now be provided to the customer. Please refer to TSB 23-01-016H (or latest version) for parts and programming information.

delivered with only one (1) complete Smart Key FOB and one additional mechanical key. This bulletin outlines the procedure to provide the 2nd Smart Key FOB and outlines programming for both Smart Key FOBs.

(2) Smart Key FOBs will receive only one (1) Smart Key FOB and one additional mechanical key, per vehicle, until further notice.

Smart Key FOBs will receive only one (1) Smart Key FOB and one additional mechanical key, per vehicle, until further notice. A second Smart Key FOB, per vehicle, will be provided at a later date.

Smart Key FOBs will receive only one (1) Smart Key FOB and one additional mechanical key, per vehicle, until further notice. A second Smart Key FOB, per vehicle, will be provided at a later date.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

system.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

system.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

caused by other wireless noise from unknown sources which could make wireless communication unstable between D-Audio and mobile phone.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This battery diagnosis function displays the various battery-related faults such as: Internal short circuit Battery deterioration Malfunction of electronic parts Insufficient battery charge Normal battery Charging defect Battery diagnosis uses the battery sensor history saved for the last 30 days and ICU diagnostic communication to track battery state of charge (SOC) and current parasitic draw history.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

equipped with an 8-speed wet dual clutch transmissions (8WDCT) that improves the touch point learning variation. Certain 8WDCTs (indicated by a new part number) received an improved clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise drivability concerns may occur.

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

on the instrument cluster and various symptoms; multiple DTCs (Diagnostic Trouble Code), reduction in power steering assist, and not able to shift out of Park. Possible DTCs set are: C181287 CAN Time-out Gateway C181208 CAN Time-out Gateway C180581 LKAS CAN Signal Error C181887 CAN Time-out BCA B109052 TCU Missing Error This bulletin provides the service procedure to update the ICU (Integrated Central Control Unit) software to resolve the conditions stated above.

on the instrument cluster and various symptoms; multiple DTCs (Diagnostic Trouble Code), reduction in power steering assist, and not able to shift out of Park. Possible DTCs set are: C181287 CAN Time-out Gateway, C181208 CAN Time-out Gateway, C180581 LKAS CAN Signal Error, C181887 CAN Time-out BCA, B109052 TCU Missing Error This bulletin provides the service procedure to update the ICU (Integrated Central Control Unit) software to resolve the conditions stated above.

blind spot collision warning alert sound is on; upon reduction of speed below 10 mph, the warning sound does not turn off. When backing up/moving in reverse and the rear cross traffic collision audible warning sound is on; upon changing the transmission into Drive, the warning sound does not turn off. This bulletin provides the service procedure to update the left and right BCA (Blind-Spot Collision-Avoidance Assist) modules software to resolve the condition(s) stated above.

potentially causing premature wear due to less clearance between the disc and pressure plate. This bulletin outlines the procedures to inspect the clutch disc, and if necessary, repair the condition.

due to brake fluid entering the HECU (Hydraulic Electronic Control Unit) electrical connector. DTC C1501 (EPB Switch Failure) may be present, but EPB performance remains unaffected.

light on due to brake fluid entering the HECU electrical connector. DTC C1501 (EPB Switch Failure) may be present, but EPB performance remains unaffected. This bulletin describes the procedure to inspect, and if necessary, replace the Hydraulic Electronic Control Unit (HECU).

light on due to brake fluid entering the HECU electrical connector. DTC C1501 (EPB Switch Failure) may be present, but EPB performance remains unaffected. This bulletin describes the procedure to inspect, and if necessary, replace the Hydraulic Electronic Control Unit (HECU).

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

due to internal contamination of the front radar reception antenna. Customers may also report other systems related to the front radar being inoperative, such as Smart Cruise Control (SCC) or Forward Collision-Avoidance Assist (FCA). Other functions of the Advanced Driver Assistance System (ADAS) are not affected. Follow the procedure in this bulletin to replace the affected front radar unit and perform all related adjustments according to Shop Manual instructions.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

forward-facing center vents Mode actuator not changing airflow direction after various inputs Popping/snap noise when switching between different modes If any of the conditions above exist, follow the repair procedure in this bulletin to replace the ventilator lever.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

In normal Ackerman steering geometry, the inner front tire turns more than the outer tire to help cornering in low-speed situations, i.e., parking lot maneuvering or sharp U-turns. N vehicles have a steering geometry optimized for performance driving. The N vehicles steering angle difference between the front wheels is reduced to enhance cornering performance. While this helps in high performance driving conditions, it can cause a higher level of tire side scrub that may create a slow shudder or vibration while turning at full steering lock. The feel is similar to turning a 4WD vehicle on dry asphalt when locked in 4WD. This shudder or vibration at parking lot speeds is normal, and no repairs should be performed.