2021 Hyundai Elantra TSBs

a warning lamp for DTC P218100 (Cooling System Performance) related to the Integrated Thermal-Management Module (ITM). Follow the service procedure in this bulletin to install a spring onto the thermostat within the ITM, in order to prevent premature opening, and perform an ECU software update on affected vehicles.

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

tank assembly at idle or on an incline when the PCSV (Purge Control Solenoid Valve) is operating, and fuel level is above 90% full. If the noise is heard, follow the service procedure to replace the fuel tank assembly and resolve the concern.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

(CN7) and 2022-2023MY Kona (OS) vehicles equipped with the 1.6 liter T-GDI Gamma 2 engine, that may exhibit a warning lamp with one or more of the DTCs listed below: P250F - Engine Oil Level Too Low P011B, P050C - Engine Coolant Temperature/intake Air Temperature Correlation P00B7, P2B60 - Engine Coolant Flow Low/Performance

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

malfunction indicator light due to Diagnostic Trouble Codes (DTC) listed below. This bulletin provides information on replacing the oil pressure sensor to remedy these DTCs, rather than replacing the entire IVT assembly.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

(CN7/CN7a) vehicles equipped with the 2.0L MPI and Intelligent Variable Transmission (IVT). This update to the damper clutch logic is to address a potential engine stall condition immediately following Forward Collision Avoidance (FCA) activation under specific operating conditions at low engine RPM and low vehicle speeds. In the event a low-speed stall does occur, the engine can immediately be restarted.

update to the damper clutch logic to address a potential engine stall condition immediately following Forward Collision Avoidance (FCA) activation under specific operating conditions at low engine RPM and low vehicle speeds. In the event a low-speed stall does occur, the engine can immediately be restarted.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

Sensor (WTS) may be observed due to machining burrs at the mounting port of the cylinder head, resulting in improper coolant sealing.

machining burrs at the mounting port of the cylinder head, resulting in improper coolant sealing.

(CN7/CN7A) vehicles equipped with the 2.0L engine to update the ECM logic for the following conditions and DTCs: Incorrect learning of the fuel adaptive values can occur if the engine is started at 14F (-10C) or colder ambient temperatures. If incorrect values are learned, the engine may stall when coming to a stop or at idle. DTC P016C: Closed Loop Air/Fuel Ratio Control at Limit-System Too Lean may be detected. The ECM software revises the logic for fuel adaptation learning and improves engine performance at idle. The ECM software also revises the blower motor control duty cycle logic for DTC P1CD0: Air Blower Motor Inverter Performance.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

(CN7/CN7a) vehicles equipped with the 2.0L MPI and Intelligent Variable Transmission (IVT). This update to the damper clutch logic is to address a potential engine stall condition immediately following Forward Collision Avoidance (FCA) activation under specific operating conditions at low engine RPM and low vehicle speeds. In the event a low-speed stall does occur, the engine can immediately be restarted.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This battery diagnosis function displays the various battery-related faults such as: Internal short circuit Battery deterioration Malfunction of electronic parts Insufficient battery charge Normal battery Charging defect Battery diagnosis uses the battery sensor history saved for the last 30 days and ICU diagnostic communication to track battery state of charge (SOC) and current parasitic draw history.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

battery drain on dealer stock vehicles. The lockbox is still within the range of the receiver when it is mounted to the rear window. This will cause the key fob to continuously transmit a RF (radio frequency) to the receiver. It is recommended to use a lockbox with RFID shielding to block the RF signal and prevent battery drain.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

When Wireless CarPlay is disconnected, a pop up message Phone Not Responding. Please reconnect it and try again will appear on the radio screen. This bulletin describes the procedure to update the radio software to help reduce the disconnection occurrences.

When Wireless CarPlay is disconnected, a pop up message Phone Not Responding. Please reconnect it and try again will appear on the radio screen.

may experience an inoperable horn. Hyundai is extending the warranty coverage for the Horn Assembly under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owner.

may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

vehicles may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

vehicles may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

may experience an inoperable horn. Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this TSB to install the latest design. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this TSB to install the latest design.

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

on the instrument cluster and various symptoms; multiple DTCs (Diagnostic Trouble Code), reduction in power steering assist, and not able to shift out of Park. Possible DTCs set are: C181287 CAN Time-out Gateway C181208 CAN Time-out Gateway C180581 LKAS CAN Signal Error C181887 CAN Time-out BCA B109052 TCU Missing Error This bulletin provides the service procedure to update the ICU (Integrated Central Control Unit) software to resolve the conditions stated above.

on the instrument cluster and various symptoms; multiple DTCs (Diagnostic Trouble Code), reduction in power steering assist, and not able to shift out of Park. Possible DTCs set are: C181287 CAN Time-out Gateway, C181208 CAN Time-out Gateway, C180581 LKAS CAN Signal Error, C181887 CAN Time-out BCA, B109052 TCU Missing Error This bulletin provides the service procedure to update the ICU (Integrated Central Control Unit) software to resolve the conditions stated above.

of specification input shaft snap ring. This bulletin outlines the procedures for inspecting for 1-2 or 2-1 shift shock and replacing the input shaft snap ring.

cluster and various symptoms; multiple DTCs (Diagnostic Trouble Code), reduction in power steering assist, and not able to shift out of Park. Possible DTCs set are: C181287 CAN Time-out Gateway C181208 CAN Time-out Gateway C180581 LKAS CAN Signal Error C181887 CAN Time-out BCA B109052 TCU Missing Error

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

due to internal contamination of the front radar reception antenna. Customers may also report other systems related to the front radar being inoperative, such as Smart Cruise Control (SCC) or Forward Collision-Avoidance Assist (FCA). Other functions of the Advanced Driver Assistance System (ADAS) are not affected. Follow the procedure in this bulletin to replace the affected front radar unit and perform all related adjustments according to Shop Manual instructions.

This bulletin describes the procedure to replace the rear combination lamp turn signal light bulbs for both the right and left side.

forward-facing center vents Mode actuator not changing airflow direction after various inputs Popping/snap noise when switching between different modes If any of the conditions above exist, follow the repair procedure in this bulletin to replace the ventilator lever.

After a new vehicle launch, Hyundai uses the LQMP to monitor all customer and dealer activities at a minimum of 100 days. The Elantra LQMP helps improve model vehicle quality, and allows Hyundai to proactively respond to the Voice of the Customer (VOC).

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

Follow the procedure outlined in this bulletin to remove and replace the dark chrome front bumper moldings.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.