2015 Hyundai Elantra TSBs

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the Settlement) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service process to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

Hyundai Motor America et al., No. 2:18-cv-11249 (D.N.J.) (the Action). Customers affected by the proposed settlement have been informed of the settlement by mailed notice and email, and they may direct questions to dealers.

of the engine as described in TSB 22-EM-007H has been extended.

to possible scuffing on one or more cylinder walls. Follow the procedure outlined in this bulletin to inspect the engine and replace the engine long block along with service kit if scuffing is observed.

related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

possible scuffing on one or more cylinder walls. Follow the procedure outlined in this bulletin to inspect and replace the short engine assembly if scuffing is observed.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

and pistons, for damage related to a piston slap noise in the upper end of the engine as described in TSB # 21-EM-001H has been extended.

possible scuffing on one or more cylinder walls. Follow the procedure outlined in this bulletin to inspect and replace the short engine assembly if scuffing is observed.

as separate components.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Reverse and Drive

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

as separate components.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

follow the repair procedure and replace the related solenoid and oil pressure harness

as separate components.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

vehicles: ? 2011-2014 Sonata (YFa), 2011-2014 Sonata Hybrid (YF HEV) ? 2007-2015 Elantra (HD, MD/UD), 2009-2012 Elantra Touring (FD) The MDPS been extended to 10 years from the date of original delivery or the date of first use, or 100,000 miles, whichever occurs first. This warranty extension applies to all original and subsequent owners of the affected vehicles.

in a slight "clicking" or "thud" type noise when turning the steering wheel. The warranty coverage for this coupling has been extended to 10 years from the date of original retail delivery or date of first use or 100,000 miles, whichever occurs first. This bulletin describes the service procedure to replace the coupling. Refer to the warranty and service parts information outlined in this bulletin whenever MDPS coupling replacement is required.

in a slight "clicking" or "thud" type noise when turning the steering wheel. This bulletin describes the service procedure to replace the coupling. Refer to the warranty and service parts information outlined in this bulletin whenever MDPS coupling replacement is required.

MODULE ARE SET FOR THE APPLICABLE VEHICLE, AND IF NECESSARY, HOW TO MAKE ADJUSTMENTS TO THESE SETTINGS.

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

system (Gen 1).

with the Elantra GT (GD) Rear Spoiler replacement part kit.

IN SOME TROUBLE CODES RELATING TO THE RANGE SWITCH. *LJ

panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

Santa Fe Sport, 2019 model year Santa Fe, 2021 2023 model year Santa Fe Hybrid, and 2020 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any states law.

fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any states law.

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2011 2016MY Elantra (MD/UD) and certain 2013 2014MY Elantra Coupe (JK) vehicles.

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. The service campaign describes the procedure to perform this preventative service on certain 2011 2016MY Elantras (MD/UD) and certain 2013 2014MY Elantra Coupe (JK) vehicles.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2011 2016 Elantras (MD/UD).

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. The service campaign describes the procedure to perform this preventative service on certain 2011 2016 Elantras (MD/UD).

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. The service campaign describes the procedure to perform this preventative service on certain 2011 2016 Elantras (MD/UD).

As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2011 2016 Elantras (MD/UD).

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

(transmission clutch slip in gear above limit) listed on Page 2.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

measure shift engagement time.

This bulletin provides the diagnostic procedures to correct this condition.

converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.

TRANSMISSION (DCT).

THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE"

THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.

THE ATF LEVEL MUST BE CHECKED BY THE FOLLOWING PROCEDURE.

The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

or date of first use or 120,000 miles, whichever occurs first.

The ECM update is only emissions related. The update is for the applicable models listed below with SULEV emissions certifications only.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

DE-ACTIVATED FOR THE FOLLOWING REASONS: H A CUSTOMER WHO INITIALLY WAIVES BLUE LINK ENROLLMENT, AND THEN DECIDES TO ENROLL AFTER PURCHASE OF VEHICLE. H A CUSTOMER WHO ALLOWS ALL PACKAGES OF THEIR BLUE LINK SUBSCRIPTION TO EXPIRE AND THEN WISHES TO RE-SUBSCRIBE TO BLUE LINK. H A CUSTOMER WHO DID NOT ENROLL IN BLUE LINK WITHIN THE FIRST 30 DAYS OF OWNERSHIP (AT WHICH TIME THE DEVICE BECOMES INACTIVE), BUT THEN DECIDES TO ENROLL. H A SUBSEQUENT OWNER WHO WISHES TO ENROLL IN BLUE LINK."

APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin does not address any steering function related concerns. This bulletin provides information on replacement of the steering rack support yoke assembly.