2017 Hyundai Azera TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

as separate components.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Reverse and Drive

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

as separate components.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

experience a warning lamp being illuminated intermittently when starting the engine after replacing the motor driven power steering (MDPS) column & housing.

experience a warning lamp being illuminated intermittently when starting the engine after replacing the motor driven power steering (MDPS) column & housing. This bulletin describes the procedure to perform the steering angle sensor (SAS) reset using the GDS.

Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines.

experience a warning lamp being illuminated intermittently when starting the engine after replacing the motor driven power steering (MDPS) column & housing.

experience a warning lamp being illuminated intermittently when starting the engine after replacing the motor driven power steering (MDPS) column & housing. This bulletin describes the procedure to perform the steering angle sensor (SAS) reset using the GDS.

Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines.

follow the repair procedure and replace the related solenoid and oil pressure harness

as separate components.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

Service campaign T2M provides a service procedure to replace the inhibitor switch on certain 2017-18 Santa Fe Sport, 2017 Santa Fe, 2017-18 Tucson, 2017 Azera, 2017 Sonata, Sonata Hybrid & Plug-in.

? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

(transmission clutch slip in gear above limit) listed on Page 2.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

measure shift engagement time.

This bulletin provides the diagnostic procedures to correct this condition.

A possible symptom is Diagnostic Trouble Code P0705 (Transmission Range Sensor Circuit).

converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.

The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

pop-up message shown (intermittently) after every Head Unit boot up.

the inability to set the clock or view it on the top of the screen.

DE-ACTIVATED FOR THE FOLLOWING REASONS: H A CUSTOMER WHO INITIALLY WAIVES BLUE LINK ENROLLMENT, AND THEN DECIDES TO ENROLL AFTER PURCHASE OF VEHICLE. H A CUSTOMER WHO ALLOWS ALL PACKAGES OF THEIR BLUE LINK SUBSCRIPTION TO EXPIRE AND THEN WISHES TO RE-SUBSCRIBE TO BLUE LINK. H A CUSTOMER WHO DID NOT ENROLL IN BLUE LINK WITHIN THE FIRST 30 DAYS OF OWNERSHIP (AT WHICH TIME THE DEVICE BECOMES INACTIVE), BUT THEN DECIDES TO ENROLL. H A SUBSEQUENT OWNER WHO WISHES TO ENROLL IN BLUE LINK."

APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin provides information on how to diagnose the yoke noise and replace the rack support yoke assembly.