2018 Hyundai Accent TSBs

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

as separate components.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Drive and Reverse

the repair procedure and replace the oil pressure harness.

follow the repair procedure and replace the input/output speed sensor and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

as separate components.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

follow the repair procedure and replace the related solenoid and oil pressure harness.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

follow the repair procedure and replace the input/output speed sensor and oil pressure harness.

below, follow the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the oil pressure harness.

Service Campaign T2X provides a service procedure to replace spark plugs on certain 2018 Accent vehicles.

plug gap, and clear Diagnostic Trouble Codes (DTC). This bulletin addresses the following conditions: ? DTC P0300 / P0301 / P0302 / P0303 / P0304 Random/Multiple Misfire. ? Engine runs rough.

gap, and clear Diagnostic Trouble Codes (DTC). This bulletin addresses the following conditions: ? DTC P0300 / P0301 / P0302 / P0303 / P0304 Random/Multiple Misfire. ? Engine runs rough.

Service Campaign T2X provides a service procedure to replace the spark plugs.

and have Diagnostic Trouble Code (DTC) stored in the ECM. Hyundai is extending warranty coverage for the airbag control unit (ACU) under this condition to 15 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

and have Diagnostic Trouble Code (DTC) stored in the ECM. Hyundai is extending warranty coverage for the airbag control unit (ACU) under this condition to 15 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

ensure that the shipping fuse is completely seated in the junction box. TPMS Lamp ON Trunk Open Warning Lamp ON while trunk is closed Master Warning Mode Lamp ON Interior lights inoperative Audio system inoperative

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

This procedure is necessary to reduce the TCU learning time and improve the shift quality.

measure shift engagement time.

time.

This bulletin provides the diagnostic procedures to correct this condition.

Hyundai is extending the warranty coverage for horn replacement to 10 years / 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first). This warranty extension is valid for original and subsequent owners.

Hyundai is extending the warranty coverage for the horn replacement to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. This bulletin provides information on how to fix the inoperative horn.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

Trouble Codes (DTC) related to the Airbag Control Unit (ACU), which may cause the airbag warning light to illuminate. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, Hyundai is extending the warranty coverage for the ACU under this condition to 15 years with unlimited mileage from the date of original retail delivery or date of first use and is valid for original and subsequent owners.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.