2009 Harley-Davidson Flhx TSBs

PURPOSE: This bulletin informs dealers that changes have been made to the Camshaft Drive Gear Retention Kit and service proceduresfor the Milwaukee-Eight and Twin Cam applications. In an effort to increase the clamp load of the camshaft drive sprocket bolted joint and prevent the drive bolt from loosening in high lift camshaft applications, the following changes have been made: a. The camshaft drive bolt final torque has been increased to 40 ft-lbs (54 Nm) for all Milwaukee-Eight and certain Twin Cams models. See Vehicles Affected. This increase in torque will make the bolt a one time use application. Never re-use a camshaft drive bolt for service after tightening to the increased specification. See service manual for updated procedure. b. A new camshaft drive gear retention kit (Part No. 91800088) has been created. This new kit is compatible with all Milwaukee-Eight and Twin Cam engines using Parts and Accessories (P&A) camshaft and Original Equipment (OE) camshaft applications. See Instruction sheet for specific fitment on Twin Cam OE camshaft applications. The new kit utilizes friction washers to prevent unwanted rotation of components in the drive sprocket bolted joint under stress. The use of liquid threadlocker on the threads of the bolt and pre-lube to the head of the bolt flange and outside of the washer help the bolt reach full stretch when tightening. NOTE: Engines produced at all Harley-Davidson Motor Company (HDMC) plants will not come with the new kits installed. They will continue to be produced with (Part No. 25566-06).

PURPOSE: To inform dealerships that Harley-Davidson has made updates to oil filters including new part numbers, packaging design, and bulk case quantity changes.

Purpose: To inform dealers of an issue with the bulb wire terminals not being to specification. The light bulbs were used in numerous front and rear fender tip light assemblies for domestic and international applications.

PURPOSE: To inform dealers of certain twin cam longblock and twin cam warranty engines are no longer supported. Instead, shortblocks should be ordered where applicable.

Purpose: Technicians have been falsely identifying connecting rod bearings as failed due to a perception of resistance as the rods are rotated. The clearance of the Twin Cam and Milwaukee-Eight crank pin bearings are maintained to a very tight range. This optimizes performance and maintains low mechanical noise in operation. The connecting rod bore can also distort slightly in operation due to stress relaxation. As a result, bearing clearance decreases due to the contact zone broadening and the load being distributed over more rollers. The combination of a bore being slightly out of round and reduced bearing clearance can result in varying degrees of resistance through the range of motion. Axial clearance is also tightly controlled for proper alignment. For these reasons, zones of resistance can be found when the connecting rods are rotated by hand through their range of motion. Resistance during rod motion, by itself, is not an indication of a performance or durability concern.

Purpose: Revision. Update: Notes for Table 3 and 4. * Updated: Part Numbers. This bulletin informs dealers that all: Twin Cam gear packs on CVO, Dyna, Police, Softail, Touring & Trike models and Milwaukee-Eight gear packs on CVO, Police, Softail, Touring & Trike models ordered after December 04, 2023 will not come with the shift drum, forks, shafts and related hardware. Models Affected: 2006-2017 Twin Cams: Dyna models 2007-2016 Twin Cams: CVO, Police, Touring and Trike models 2007-2017 Twin Cams: Softail models 2017-2024 Milwaukee-Eight: CVO, Police, Touring and Trike models 2018-2024 Milwaukee-Eight: Softail models

Purpose: This bulletin informs dealers that all: Twin Cam gear packs on CVO, Dyna, Police, Softail, Touring & Trike models and Milwaukee-Eight gear packs on CVO, Police, Softail, Touring & Trike models ordered after December 04, 2023 will not come with the shift drum, forks, shafts and related hardware. Note: Resubmission is a correction to Selected Products Section of Transaction ID 24MC44619, NHTSA ID 10248397. Models Affected by M1612 to include only: 2006-2017 Twin Cams: Dyna models 2007-2016 Twin Cams: CVO, Police, Touring and Trike models 2007-2017 Twin Cams: Softail models 2017-2024 Milwaukee-Eight: CVO, Police, Touring and Trike models 2018-2024 Milwaukee-Eight: Softail models

Purpose: This bulletin informs dealers that all: Twin Cam gear packs on CVO, Dyna, Police, Softail, Touring & Trike models and Milwaukee-Eight gear packs on CVO, Police, Softail, Touring & Trike models ordered after December 04, 2023 will not come with the shift drum, forks, shafts and related hardware.

PURPOSE: Revision E. Added: Added procedures for the DCA-8000 E Battery Tester.* Updated: All sections. This bulletin informs the dealership network that Harley-Davidson has provided guidelines for battery warranty.

PURPOSE: This bulletin informs dealers that Harley-Davidson has made a software update to Digital Technician II (DT II). DIGITAL TECHNICIAN II (PART NUMBER: HD-48650). Version 24.8.8. Release Date: Week of August 5, 2024. New Features for Harley-Davidson vehicles: Advanced Module Replace for 2021 and later Revolution Max; 2023 and later CVO Touring; and 2024 Street Glide (FLHX), Road Glide (FLTRX). New Features for LiveWire vehicles: Updated calibrations for 2024 S2DM EV1/ EV6; 2024 S2MH EV1; and 2024 S2DM, S2MH. Changes: Added Hand Control Module (HCM) (Part No. 71500522A and 71500536A) for reflash support.

PURPOSE: Revision. This bulletin informs dealers that Harley-Davidson has made a software update to Digital Technician II (DT II). DIGITAL TECHNICIAN II (PART NUMBER: HD-48650). Version 24.6.4. Release Date: Week of May 1, 2024. New Features for LiveWire S2DM and S2MH, 2024 Revolution Max, and 2024 Touring.

PURPOSE: Initial Release. This bulletin informs dealers of the availability of new batteries for new Original Equipment (OE) vehicle production and in the Parts and Accessories (P&A) catalog. Availability of the new Absorbed Glass Mat (AGM) batteries will vary by market and will be transitioning over the next few months. NOTE: The ring terminal screws are not compatible between Leoch and East Penn batteries. The new batteries will include new ring terminal screws, which must be used. The ring terminal screws from the old battery need to be discarded.

PURPOSE: Revision. Some 2009 - 2020 Touring, Touring CVO, Touring Police models exhibit drainage of rusty water from the rear fork (where the debris deflector mounts), which has raised customer concern. Updated Model Years. NOTE: This is a cosmetic concern and not an indication of an internal issue.