2019 GMC Yukon Denali TSBs

internal engine damage.

repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

sticking valve that may cause the MIL to illuminate.

parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

GDS 2.

customer.

issue.

consumption.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

service or aftermarket calibrations.

GDS 2.

consumption.

occurrence.

possibilities of what may happen using the incorrect filter.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

GM has determined that wheel refinishing under warranty will no longer be performed.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

conductive finish.

parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

and improve fuel economy.

service or aftermarket calibrations.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

Dealers Only).

Recommendations.

consumption.

Dealers Only).

possibilities of what may happen using the incorrect filter.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

service or aftermarket calibrations.

GDS 2.

engine related shudder.

consumption.

driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

issue.

issue.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

service or aftermarket calibrations.

internal engine damage.

Dealers Only).

that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

may have no Reverse and no 2nd gear.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

customer.

gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

GDS 2.

Identification.

consumption.

service or aftermarket calibrations.

internal engine damage.

engine is started while diagnosing for noise from the engine or transmission.

which will need to be installed to correct the repair.

Recommendations.

and improve fuel economy.

engine related shudder.

Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

Dealers Only).

Dealers Only).

or the vehicle has sat for a few hours.

engine related shudder.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

contain the letter O or the number 0.

10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of these DTCs.

Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.

have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.

have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.

repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.

Dealers Only).

Trailer Brake message in the Driver Information Center. Also the vehicle will have a Diagnostic Trouble Code U0415 set. Technician will fill the master cylinder brake fluid reservoir to the maximum level.

correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.

with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped

factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.

have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.

contain the letter O or the number 0.

White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.

vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.

factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.

Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308 may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.

not pass California smog inspection or smog inspection in other states.

programs.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

Only).

programs.

before being sold (prepping) to the customer.

that request to disable or enable content.

programs.

Only).

before being sold (prepping) to the customer.

shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

Only).

programs.

(WPC) Parts Return Program.

identification for warranty transactions (U.S. Only).

and Canada Dealers Only).

submit a Pre-Repair Authorization (PRA).

unlocking.

Dealer Special Tool Loan Program process.

operation.

replacements.

Dealers Only).

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.

repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

services and maintenance on vehicles originating/sold in Canada.

replacements.

the warranty transaction submission procedures that support the Personal Property Damage process.

Only).

before being sold (prepping) to the customer.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

FAQs.

unlocking.

a fluid leak, and what is considered fluid seepage.

Assistance Center (TAC).

Only).

programs.

shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

that request to disable or enable content.

Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

(WPC) Parts Return Program.

Only).

and Canada Dealers Only).

Only).

Only).

submit a Pre-Repair Authorization (PRA).

submit a Pre-Repair Authorization (PRA).

warped or misshapen.

FAQs.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Dealer Special Tool Loan Program process.

Assistance Center (TAC).

Dealers Only).

Only).

Only).

Only).

Dealers Only).

vehicles before being sold (prepping) to the customer.

Spin-On Oil Filters.

to GM for payment.

identification for warranty transactions (U.S. Only).

operation.

Only).

the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.

Dealers Only).

that request to disable or enable content.

the warranty transaction submission procedures that support the Personal Property Damage process.

(WPC) Parts Return Program.

Only).

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

and Canada.

Spin-On Oil Filters.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.

Only).

submit a Pre-Repair Authorization (PRA).

Only).

submit a Pre-Repair Authorization (PRA).

Only).

replacements.

warped or misshapen.

Spin-On Oil Filters.

vehicles before being sold (prepping) to the customer.

independent causes (GM Canada Dealers Only).

replacements.

replacements.

Spin-On Oil Filters.

vehicles before sold (prepping) to the customer.

DTC'ss

DTC's

DTC's

DTC's

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

for certain repairs, such as Wiring Harness Repairs.

warranty replacements.

repairing wiring harnesses.

(U.S).

warranty replacements.

It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

warranty replacements.

warranty replacements.

repairing wiring harnesses.

warranty replacements.

warranty replacements.

condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

causing a battery draw.

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

that may be caused by a module back feeding voltage in the ignition relay circuits making the vehicle think it is still awake.

causing a battery draw.

block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.

causing a battery draw.

causing a battery draw.

During inspection Technician may notice DTC P1682 (Ignition 1 Switch Circuit 2) active or stored in history. DTC?s P0101, P0689. P16A7 or P16BC may also be active or stored in history. Additionally, vehicle may have been into the dealer on a prior service visit and had the MAF sensor replaced for DTC P0101.This condition may be caused by a faulty ignition relay or underhood fuse block terminal concern.

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.

these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 inches long. Fully open the liftgate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the liftgate actuator by following the liftgate power assist actuator procedure in service information.

these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

that may be caused by a module back feeding voltage in the ignition relay circuits making the vehicle think it is still awake.

programmedfob in the vicinity of the passive liftgate antenna. If the antenna can locate a programmed fob in saidarea, the gate will open if the liftgate open switch or hands free sensor is activated.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

Crank,SIR Light / Service Airbag Message, Service Suspension Message,Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback,HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164,U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.

Assistance Case in CX Connect.

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

system and replace the parts that may be contaminated due to oil in system.

system and replace the parts that may be contaminated due to oil in system.

Allegation Resolution (PAR) claim.

Allegation Resolution (PAR) claim.

offered through GM.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

Allegation Resolution (PAR) claim.

offered through GM.

offered through GM.

cruise control.

offered through GM.

interiors of GM vehicles.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

click with a feel of increased resistance when the accelerator pedal is about of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.

providing additional information on the AFM and DFM systems

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

due to seeing grease or sealant on certain locations on the gear.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

transmission leaking ATF causing the customers concern.

engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

no problem was found, to replace the tbv.

due to seeing grease or sealant on certain locations on the gear.

test.

engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

speed transmission are on restriction through the ProductQuality Center. Dealers are advised to contactthe ProductQuality Center if diagnostics has lead to replacement of the transmission torque converter.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

speed transmission are on restriction through the ProductQuality Center. Dealers are advised to contactthe ProductQuality Center if diagnostics has lead to replacement of the transmission torque converter.

restriction has ended.

speed transmission are on restriction through the ProductQuality Center. Dealers are advised to contactthe ProductQuality Center if diagnostics has lead to replacement of the transmission torque converter.

Dealers are to contact theProduct Quality Center before replacing the transmission assembly.

Dealers are to contact theProduct Quality Center before replacing the transmission assembly.

Dealers are to contact theProduct Quality Center before replacing the transmission assembly.

addressing underbody component corrosion with customers.

have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

peeling, metal shows corrosion/rusting (U.S. and Canada Only).

shipping film.

Guidelines.

peeling, metal shows corrosion/rusting (U.S. and Canada Only).

characteristic.

Aluminum Wheels.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

addressing underbody component corrosion with customers.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Guidelines.

addressing underbody component corrosion with customers.

characteristic.

Replacement Guidelines.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

addressing underbody component corrosion with customers.

whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.

sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver?s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver?s door remains open the alarm will not turn back on and the new transmitters can be programmed.

Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver's door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver's door remains open the alarm will not turn back on and the new transmitters can be programmed.

strut due to fluid leak.

strut due to fluid leak.

disk on gasket sealing surfaces or reused parts.

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

disk on gasket sealing surfaces or reused parts.

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

disk on gasket sealing surfaces or reused parts.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.

theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".

repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within 2.0 mm (0.079 in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.

vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the affected vehicles will be mailed an owners manual and warranty insert containing this information in English and Spanish.

written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the applicable vehicles will be mailed an owners manual and warranty insert containing this information in English and Spanish.

Replaced During Warranty Coverage Period.

Schedules.

Replaced During Warranty Coverage Period.

Accessories.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

Coverage Period.

Tires and PDI installed Limited Production Option (LPO) Tires.

Fog/Driving Lamp Damage.

Accessories.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

Coverage Period.

Coverage Period.

Tires and PDI installed Limited Production Option (LPO) Tires.

that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.

who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.

analysis.

additive.

additive.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

additive.

additive.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

additive.

available.

Vehicles.

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

ride characteristics of GM cars and trucks.

functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).

functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).

functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

Remote Keyless Entry (RKE) Fob or Passive Unlocking Range due to a internal concerns within the antenna.

being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message

feet.) Some customers may comment that the RKE fob must be held next to the driver door handle before the doors will unlock when passively attempting to unlock the door. The Radio Antenna Amplifier may be causing the range issue.

feet.) Some customers may comment that the RKE fob must be held next to the driver door handle before the doors will unlock when passively attempting to unlock the door. The Radio Antenna Amplifier may be causing the range issue.

being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message

weather climates and testing those batteries.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.