2010 Gmc Sierra 3500 TSBs
605 Technical Service Bulletins across 17 categories
Categories
Engine
139 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This Preliminary information communicates information on adding RPO UF3 Fast Idle to a vehicle.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
Revised HVAC Blower Motor Installation Instructions.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Information for Engine Oils Used in 2014 Model Year Vehicles
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that...
Read full bulletin
have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
Special Coverage. On some vehicles equipped with a 6.6L Duramax Diesel engine (RPO LML, LGH) the malfunction indicator...
Read full bulletin
lamp (MIL) may illuminate due to a condition with the glow plugs. When diagnosed, replacement of one of the engines glow plugs may be required. No drivability issues are generally associated with this issue, but harder starting in cold ambient temperatures may be noted. Dealers are to replace the affected glow plug. The repairs will be made at no charge to the customer.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
New Tool Availability - EN-48974-EGR Cooler Pressure Tester Adapter Set to Diagnose Duramax Diesel Engine EGR Cooler...
Read full bulletin
Engine Coolant Leaks into Combustion Chamber
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This preliminary information explains that there are differences between the Elevated Idle, PTO and High Idle options.
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the...
Read full bulletin
radio clock may not display the time. Dealer technicians are advised of atemporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac, Pontiac,and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the...
Read full bulletin
radio clock may not display the time.Dealer technicians are advised of atemporary proicedure to get the clock to display until Engineering has developed the permanent repair.The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication advises the technician that vehicles to look for debris in the valve bodu for...
Read full bulletin
codesP0751, P0752, P0756, P0757, P0776, P0777, P0796, P0797, P2714 or P2715, And to review the date code on the Transmission control module.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that a whine noise heard from the...
Read full bulletin
automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the...
Read full bulletin
radio clock may not display the time. Dealer technicians are advised to contact General Motors TAC for further instructionsfor a temporary repair until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
This preliminary informational bulletin provides a diagnostic tip for coolant leak at oil cooler inlet pipe o-ring after...
Read full bulletin
service engine replacement.
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline...
Read full bulletin
engines using Tech 2 or GDS 2 (U.S. and Canada).
This Preliminary Information communication advises the technician that the 2ML70 Transmission Assembly will be placed on...
Read full bulletin
restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley.
Read full bulletin
The bulletin provides information on how to correctly install the parts to function as intended.
This informational bulletin provides information to the technician on what parts of an engine or transmission will...
Read full bulletin
require the PQC to be notified.
44180 01 - Customer Satisfaction - Certain vehicles may have key codes which were inappropriately handled by a third...
Read full bulletin
party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode,...
Read full bulletin
and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides information to dealership personnel on proper engine and automatic...
Read full bulletin
transmission/transaxle identification.
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations...
Read full bulletin
for customer concerns related to wheel alignment.
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine...
Read full bulletin
breakdown or non-function due to aftermarket power-up devices vs. non overpower engine non-function of pistons, cylinders, valve train components, and DTC P003A or P111D set.
This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged,...
Read full bulletin
disassembled or improperly packaged turbochargers returned to Warranty Part Center.
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware...
Read full bulletin
Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and Transmission Data Screen
This informational bulletin provides Information on Identifying Duramax Diesel Overpower Engine Breakdown/Non-Function...
Read full bulletin
Due to Aftermarket Power-Up Devices vs Non Overpower Engine Non-Function of Pistons, Cylinders, Valvetrain Components, DTC P003A or P111D Set
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size...
Read full bulletin
trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor.
Read full bulletin
The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
44180 02 - Customer Satisfaction.
Read full bulletin
Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and...
Read full bulletin
replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts.
Read full bulletin
Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about customers that may complain of...
Read full bulletin
various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats.
Read full bulletin
Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE...
Read full bulletin
ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. TECHNICIAN WILL FOLLOW SERVICE INFORMATION DIAGNOSIS FIRST. IF SERVICE INFORMATION DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN PERFORM A CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT SYSTEM COMPRESSION TEST IN SERVICE INFORMATION. IF THE RUNNING COMPRESSION OF THE MISFIRING CYLINDER STAYS BELOW 25 POUNDS PER SQUARE INCH REGARDLESS OF THE ACTIVE FUEL MANAGEMENT SOLENOID BEING COMMANDED ON OR OFF, AN ACTIVE FUEL MANAGEMENT LIFTER IS MECHANICALLY COLLAPSED/STUCK OR UNLOCKING AS SOON AS THE ENGINE IS STARTED. REPLACE ALL ACTIVE FUEL MANAGEMENT LIFTERS, AND ALL PLASTIC LIFTER GUIDES. ALSO PERFORM THE CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT VALVE LIFTER OIL MANIFOLD DIAGNOSIS AND TESTING IN SERVICE INFORMATION. IF IT ISOLATES A CONCERN WITH THE VALVE LIFTER OIL MANIFOLD, REPLACE IT AND REEVALUATE THE CONCERN. THE ACTIVE FUEL MANAGEMENT LIFTERS CAN ALSO BE MONITORED FOR PROPER OPERATION BY CAREFULLY INSPECTING THE CYLINDER 1, 4, 6, AND 7 ROCKERS AND VALVES WHILE CRANKING OR BRIEFLY AND SAFELY RUNNING THE ENGINE WITH THE VALVE COVERS REMOVED. IF THE VALVE OR VALVES OF AN ACTIVE FUEL MANAGEMENT CYLINDER STOP MOVING WHILE DOING THIS TEST, THE ACTIVE FUEL MANAGEMENT LIFTER IS CAUSING THE CONCERN. FOR 2008-2009 FULL SIZE TRUCK/SUV OR A 2007-2009 CHEVROLET TAHOE WITH THE POLICE PACKAGE REPROGRAM THE ENGINE CONTROL MODULE. ON THE 2008-2009 PONTIAC G8, 2010-2011 CAMARO, AND 2007-2010 FULL SIZE TRUCKS WITH ACTIVE FUEL MANAGEMENT, ALSO DETERMINE IF THE ACTIVE FUEL MANAGEMENT PRESSURE RELIEF VALVE SHIELD THAT IS LISTED IN THE LATEST VERSION OF 10-06-01-008 HAS EVER BEEN INSTALLED. ON PASSENGER CARS WITH THE LS4 ENGINE, DETERMINE IF THE UPDATED OIL PAN GASKET THAT IS LISTED IN THE LATEST VERSION OF 11-06-01-007 HAS BEEN INSTALLED.
14653 - SPECIAL COVERAGE.
Read full bulletin
SOME 2010-2014 MODEL YEAR CHEVROLET EXPRESS, 2011-2014 MODEL YEAR CHEVROLET SILVERADO HD, 2010-2014 MODEL YEAR GMC SAVANA AND 2011-2014 MODEL YEAR GMC SIERRA HD VEHICLES EQUIPPED WITH A 6.6L ENGINE (RPO LML OR LGH), MAY HAVE A CONDITION WHERE THE INDIRECT FUEL INJECTOR CAN BECOME STUCK IN THE CLOSED POSITION OR CAN HAVE LOW FLOW. THIS CONDITION COULD RESULT IN THE ILLUMINATION OF THE MALFUNCTION INDICATOR LIGHT (MIL). DEALERS ARE TO REPLACE THE INDIRECT FUEL INJECTOR AS NECESSARY WITH AN IMPROVED SERVICE PART.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO...
Read full bulletin
REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN.
Read full bulletin
A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL...
Read full bulletin
TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE.
Read full bulletin
TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER...
Read full bulletin
DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL...
Read full bulletin
ENGINE DAMAGE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE...
Read full bulletin
GASKET SEALING SURFACES.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF...
Read full bulletin
AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN.
Read full bulletin
A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
THIS TSB CONTAINS AN OWNER NOTIFICATION LETTER.
Read full bulletin
SELECT DOCUMENT SEARCH BUTTON BELOW. GENERAL MOTORS 2010-2011 CHEVROLET EXPRESS AMD GMC SAVANA W/6.6L DIESEL ENGINE: THE OXIDE SENSOR MAY FAIL DUE TO CONTAMINATION BETWEEN THE TERMINALS IN THE SENSOR AND THE WIRE INTERFACE. *LJ
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE.
Read full bulletin
MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON...
Read full bulletin
ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE
GENERAL MOTORS: DIAGNOSING POWER STEERING CONCERNS.
Read full bulletin
IN RARE CASES, CUSTOMERS MAY COMMENT ON A LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE OF MANEUVERS. *JS UPDATED 09/02/14*LJ
CHEVROLET/GMC: SNOW OR ICE INGESTION INTO AIR CLEANER ELEMENT, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, ENGINE...
Read full bulletin
POWER IS REDUCED MESSAGE DISPLAYED, DTC P0101 SET (PERFORM REPAIR AS OUTLINED). *PE
GENERAL MOTORS: ENGINEERING INFORMATION-CHEMICAL DAMAGE ON INNER SURFACES OF FUEL TANK.
Read full bulletin
SOME CUSTOMERS MAY COMMENT ON POOR PERFORMANCE, DECREASED ACCELERATION AND/OR AN INOPERATIVE FUEL GAUGE. NO MODELS LISTED EXCEPT SATURN AND HUMMERS; INCLUDES ALL PASSENGER CARS AND LIGHT DUTY TRUCKS. *PE UPDATED 5/9/11. *PE
Other
116 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
NQG 4WD Models With Noise Vibration On Dry Pavement.
NQG 4WD Models With Noise Vibration On Dry Pavement.
Vibration On Dry Pavement.
NQG 4WD Models With Noise Vibration On Dry Pavement
Cold Extended Crank .
Information on Driveline Clunk Noise
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Speedometer Needle Accuracy Information.
Speedometer Needle Accuracy Information
Whistle Noise From Drivers Side A Pillar Area.
Whistle Noise From Drivers Side A Pillar Area
Bump Feel Or Clunk Noise After A Stop.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Adding Cruise Control (RPO K34)
Cold Air Leak On Passenger Floor.
Normal Characteristic - RKE Inoperative / Unable To Program Fobs.
Unwanted Stability Activation And/Or C0710.
Speedometer Needle Accuracy Information.
Speedometer Needle Accuracy Information
Whistle Noise From Drivers Side A Pillar Area.
Whistle Noise From Drivers Side A Pillar Area
Bump Feel Or Clunk Noise After A Stop.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Terminal Test Probe And Replacement Terminal.
Changing Turn-By-Turn Voice Response To Metric Or English Units
PAC Courtesy Transportation Assistance Program
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Information on Driveline Clunk Noise
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Canadian Customers Unable To Place Calls In The United States
GM Accessory Heated Seats Inoperative After Installation.
GM TAC Support of Vehicle Vibration Complaints.
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
Requesting a New Key Code for Customer with Lost or Stolen Keys
Removing / Disabling Rear Park Assist RPO UD7.
Adding Cruise Control (RPO K34)
Unwanted Stability Activation And/Or C0710.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides you with contacts in event of the installation of Cruise control.
Information.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
Information on Mounting Points for Pickup Box Accessories
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate.
Read full bulletin
Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using...
Read full bulletin
Customer Concern Verification Sheets (CCVS).
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar...
Read full bulletin
RemoteLink? phone application.
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the...
Read full bulletin
appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the...
Read full bulletin
Approved Refinish Materials booklet information.
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
This preliminary information bulletin provides information on installing new rivets on the accessory tonneu cover to...
Read full bulletin
correct a customers comments on the cover seeming loose
This informational bulletin provides information on the proper oils to use on GM vehicles including information...
Read full bulletin
regarding the differences of the Dexos oils.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
This information bulletin advises of a new tool used to aid in installing Duramax glow plugs.
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to...
Read full bulletin
contact PQC prior to replacing an assembly (U.S. and Canada only).
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded...
Read full bulletin
manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This information provides the proper way to install the floor mats .
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key...
Read full bulletin
Fob or OnStar Mobile Application and where to locate the information for future use.
This Preliminary Information communication provides information to the technician about vehicles that have water or dust...
Read full bulletin
from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the...
Read full bulletin
first time.
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to...
Read full bulletin
properly disable the SIR system for repairs at or near
This Preliminary Information communication provides information to the technician about connectivity concerns when...
Read full bulletin
connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
This Preliminary Information communication provides information to the technician that fluid contamination may be...
Read full bulletin
directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN.
Read full bulletin
THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES.
Read full bulletin
GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS...
Read full bulletin
LESS THAN 10,000 MILES ON IT.
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ABOUT THE DEF USE AND TREATMENT OF THE FLUID.
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Electrical
77 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Special Coverage Adjustment ? Throttle Position Sensor Replacement
High Voltage Safety ? High Voltage Disabling
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Driver or Passenger Door Module DTC B2555.
Diagnosing / Troubleshooting Multiple Electrical Concerns / Intermittent No Crank
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Driver or Passenger Door Module DTC B2555.
Intermittent Battery Draw Dead Battery Or HVAC Odor.
Programming And Activation Of Replacement OnStar Modules.
GM Wiring Repair Strategy Information
Special Coverage Adjustment ? Throttle Position Sensor Replacement
High Voltage Safety ? High Voltage Disabling
High Voltage 2-Mode Battery Parts Restriction-TAC
Diagnosing / Troubleshooting Multiple Electrical Concerns / Intermittent No Crank
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
OnStar Voice Fallback Number Update Some customers may have received a letter from OnStar stating that "We recently...
Read full bulletin
tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1.
Read full bulletin
IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
This Preliminary Information communication provides information to the technician with the installation of Cruise...
Read full bulletin
Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides steps the technician will take to repair a no crank/no start concern...
Read full bulletin
with a diagnostic trouble code of B009F in the Serial Data Gateway Module equipped with Regular Production Option code HP2. The vehicle may exhibit a no crank or no start, or a Service Hybrid message with no codes. The technician will inspect the High Voltage Circuit Impact Detection sensor for water intrusion or corrosion at the weather pack. Inspect the High Voltage Circuit Impact Detection sensor for cracks or terminal corrosion and replace the sensor or terminals along with the weather pack seals if damage is found. If there is no damage found the technician will leave the sensor unplugged and power up the vehicle to induce a code, then power down the vehicle with the Tech 2 unplugged from the vehicle for two minutes. Clear the code and recheck for the message and codes, if the code resets the technician will replace the High Voltage Circuit Impact Detection sensor and terminals with terminated leads. Technician is to repeat the above steps to verify the concern is corrected.
This Preliminary Information communication advises the technician thata P0C28 will not cause a No Crank.
Read full bulletin
also covers a Serail number for bad Aux pump module
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when...
Read full bulletin
using a second stage manufacturer
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on control module diagnostics and configuration, programming using...
Read full bulletin
the TIS Service Programming System (SPS), set-up and warranty.
This informational bulletin adds models to information on voltmeter gauge fluctuation due to regulated voltage control...
Read full bulletin
system and concerns about camper/trailer battery charging.
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This informational bulletin adds 2011 - 2014 model years to information on voltmeter gauge fluctuation due to...
Read full bulletin
regulated voltage control system and concerns about camper/trailer battery charging.
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always...
Read full bulletin
be re-learned when accessory wheels are installed on the vehicle.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician with the installation of Cruise...
Read full bulletin
Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers...
Read full bulletin
and booster packs.
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a...
Read full bulletin
long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
This preliminary informational bulletin provides technicians with repair information on removing seized exhaust...
Read full bulletin
temperature sensors.
This warranty informational bulletin advised the technician that when performing a wiring repair, more information is...
Read full bulletin
required.
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can...
Read full bulletin
cause the BCM to appear off line.
This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on...
Read full bulletin
Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box Removed
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance,...
Read full bulletin
it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
This Preliminary Information communication provides information to the technician about vehicles that during battery...
Read full bulletin
parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on...
Read full bulletin
certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on...
Read full bulletin
certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN OUTSIDE AIR TEMPERATURE INOPERATIVE.
Read full bulletin
TO PERFORM AN INSTANT UPDATE OF THE AMBIENT TEMPERATURE SENSOR, PRESS AND HOLD THE RECIRC BUTTON AND AIR CONDITIONING BUTTON ON THE HEATER-VENT-AIR CONDITIONING CONTROL HEAD SIMULTANEOUSLY. IT IS ALSO POSSIBLE TO PERFORM THIS BY USING A SCAN TOOL IN SPECIAL FUNCTION MODE AND SELECT INSTANT UPDATE.
THIS PRELIMINARY BULLETIN PROVIDES A INFORMATION ON HOW TO REMOVE THE SEIZED TEMPERATURE SENSORS FROM THE DPF.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON...
Read full bulletin
MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON...
Read full bulletin
MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC...
Read full bulletin
DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC...
Read full bulletin
DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING...
Read full bulletin
CONTROL MODULES
GMC/CHEVROLET: SEE DOCUEMTN SEARCH BUTTON FOR OWNER LETTER.
Read full bulletin
AUXILIARY BATTERY FEED MAY CAUSE FUSIBLE LINK TO MELT AND OPEN CIRCUIT TO PREVENT DAMAGE OR FIRE IN WIRING HARNESS, DUE TO ELECTRICAL OVER LOAD. *PE
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL...
Read full bulletin
MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). *PE UPDATED 3/26/10. *PE UPDATED 6/6/11. *PE UPDATED 3/12/12. *PE
Pre-Delivery & Maintenance
68 bulletinsThis warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Vehicle Recalls
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to...
Read full bulletin
Enhance Customer Service Experience
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to...
Read full bulletin
Enhance Customer Service Experience
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This warranty administration bulletin provides policy information on required operating procedures.
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product...
Read full bulletin
field action customer reimbursement procedure (U.S. Dealers Only).
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab...
Read full bulletin
Warranty Information.
This preliminary informational bulletin provides a revision of PI0388B to add the Cadillac XTS model, graphics, improved...
Read full bulletin
Instructions and Warranty Information.
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor...
Read full bulletin
Operations and Customer Enthusiasm
This warranty administration bulletin provides policy information with the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor...
Read full bulletin
Operations and Customer Enthusiasm
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs...
Read full bulletin
offered through GM.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON...
Read full bulletin
VEHICLES ORIGINATING/SOLD IN CANADA.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND...
Read full bulletin
MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
Fuel System
36 bulletinsThis service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
Duramax Fuel System Contamination Identification.
Duramax Fuel System Contamination Identification.
Service Exhaust Fluid System Message Displayed.
Duramax Diesel Glow Plugs Difficult to Install Due to Carbon Buildup - New Glow Plug Bore Reamer Available
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
Fuel Gauge Shows Empty After Refueling And DTC P2636.
Information on Exhaust Fluid Range, Exhaust Fluid Quality Poor, Service Exhaust Fluid System or Service Emission System...
Read full bulletin
Driver Information Center Messages
Information on Exhaust Fluid Range, Exhaust Fluid Quality Poor, Service Exhaust Fluid System or Service Emission System...
Read full bulletin
Driver Information Center Messages
Duramax Diesel Glow Plugs Difficult to Install Due to Carbon Buildup - New Glow Plug Bore Reamer Available
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
Clean Exhaust Filter see owners manual now or cleaning exhaust filter keep driving until message is cleared displayed on...
Read full bulletin
DIC, DTC P2463 May be set
This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the...
Read full bulletin
fuel system causing the vehicle to have a hard or no start.
This SKU is a Diesel Fuel Filter Housing.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the fuel filter threads. The threads may be misformed such that the fuel filter cannot be installed.
This SKU is a Diesel Fuel Filter Housing.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the fuel filter threads. The threads may be misformed such that the fuel filter cannot be installed.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This informational bulletin provides information on top tier fuels and what brands are available.
This preliminary informational bulletin provides inspection and repair information that may be helpful to correct...
Read full bulletin
customer concerns of XM/Cellular Mobile Phone/OnStar antenna looseness or damage, XM/Cellular/OnStar reception performance degraded, rattle/flutter/squeak noise, wind noise/whistle at highway speeds, and/or a water leak on headliner at sunvisor.
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year.
Read full bulletin
Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the...
Read full bulletin
fuel system causing the vehicle to have a hard or no start.
This preliminary informational bulletin provides service personnel with a guide to determine which SI documents and scan...
Read full bulletin
tool parameters to reference when encountering an: Exhaust Fluid Quality Poor message displayed, and a Reductant Fluid Quality Test status that will Pass, Time Out, Fail or Interrupt and other DEF messages that maybe observed.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE DIESEL OXIDATION CONVERTER PART RESTRICTION HAS ENDED.
Read full bulletin
DEALER CAN NOW ORDER THE PARTS THROUGH THE REGULAR CUSTOMER CARE AND AFTERSALES PARTS PROCESS.
GM: THE VEHICLE PERFROMANCE MAY BE POOR WITH AN INOPERATIVE FUEL GAUGE.
Read full bulletin
THE MALFUNCTION LIGHT MAY ALSO BE ON. *RM
Transmission
27 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Diagnostic Information for Transmission.
Auxiliary Transmission Fluid Pump.
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit...
Read full bulletin
part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Pressure Hose During Extreme Low...
Read full bulletin
Temperature Operation (Replace Power Steering Fluid)
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096...
Read full bulletin
TransFlow.
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a...
Read full bulletin
customers comments regarding one being broken.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This informational bulletin was created for the Manual Transmission Operating Characteristics.
Read full bulletin
The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on.
Read full bulletin
Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
This warranty administration bulletin provides information on the change in automatic transmission add conditions...
Read full bulletin
documentation and claim submissions
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing.
Read full bulletin
Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet...
Read full bulletin
protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT...
Read full bulletin
ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS."
BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS...
Read full bulletin
FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE
Body & Paint
25 bulletinsThis PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
Appearance of Discoloration or Corrosion Near Edges.
Rear and Side Tempered Glass Spots.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
Swapping Outside Rearview Mirrors RPOs DL8 / DL3 / DPN.
This service bulletin provides information on Paintless Dent Repair Process.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining...
Read full bulletin
when the protective shipping film is removed from certain vehicles.
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of...
Read full bulletin
chromed aluminum wheels, along with warranty information regarding these conditions.
This technical bulletin provides a procedure for adding double sided tape on the right and left windshield side reveal...
Read full bulletin
moldings to remove tapping, clicking or ticking type noise.
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin...
Read full bulletin
to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
This preliminary informational bulletin provides a procedure on how to clean overspray from chorme bumpers for concerns...
Read full bulletin
related to an apperance of discoloration or corrosion near edges/openings of chrome bumpers
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN...
Read full bulletin
TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR...
Read full bulletin
AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT...
Read full bulletin
CORROSION WITH CUSTOMERS.
Tires & Wheels
22 bulletinsThis Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This service bulletin provides information on Tire Sidewall Irregularities.
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
Diagnostic Tips for Difficult to Resolve Tire/Wheel Vibration Concerns
Proper Wheel Installation and Wheel Torque Techniques
Proper Wheel Installation and Wheel Torque Techniques
Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip
Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
This informational bulletin provides the technician with information on tire radial force variations and how to balance...
Read full bulletin
a tire using the balancer.
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the...
Read full bulletin
matching depth of socket used on the wheel nut.
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and...
Read full bulletin
balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
This informational bulletin communicates GM's position on use of nitrogen gas in tires.
THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT...
Read full bulletin
EQUIPMENT.
Infotainment
19 bulletinsAudio System Speaker Rattle, Buzz Noise, Poor Sound
XM Audio Traffic And Travel Link Availability And Operation.
Bluetooth Stays Connected After RAP Is Canceled.
Bluetooth Stays Connected After RAP Is Canceled.
Radio Button Backlighting Inoperative.
Information On Requests To Add OnStar Bluetooth Option.
Radio Button Backlighting Inoperative.
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged...
Read full bulletin
radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the...
Read full bulletin
techline/service programming systems.
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states...
Read full bulletin
that they only get a few channels.
This preliminary informational bulletin provides procedures to inspect , replace, or repair the XM radio antenna to...
Read full bulletin
correct the customers concern loss XM services, noise and/or water leak.
This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss...
Read full bulletin
of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth Issues
This Preliminary Information communication provides information to the technician about vehicles that have a message on...
Read full bulletin
the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
This Preliminary Information communication provides information to the technician about vehicles that have a message on...
Read full bulletin
the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS...
Read full bulletin
OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ISSUES
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO...
Read full bulletin
VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN...
Read full bulletin
THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED. "
Brakes
18 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
Stabilitrak/Traction Control OFF With Red Brake Warning Lamp
Diagnostic Tip - Service Trailer Brake Message And Unable To Clear DTCs
Stabilitrak/Traction Control OFF With Red Brake Warning Lamp
Diagnostic Tip - Service Trailer Brake Message And Unable To Clear DTCs
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full...
Read full bulletin
Turns.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need...
Read full bulletin
to be replaced if the brake pedal moves or applies on its own at a full turn.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need...
Read full bulletin
to be replaced if the brake pedal moves or applies on its own at a full turn.
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer...
Read full bulletin
concern of seeing a white film/residue on the IP pad and/or door trim panels.
This preliminary bulletin provides a procedure to reprogram the trailer brake control module to correct the customers...
Read full bulletin
concern of reduced braking during certain loads and road conditions.
This technical bulletin provides a procedure to either refinish or replace the front rotors for a condition of brake...
Read full bulletin
induced pulsation, vibration felt in steering wheel, rumble noise from underbody during downhill descents.
CHEVROLET/GMC: WITH TRAILER LOAD AND CERTAIN KIND OF ROAD CONDITIONS, BRAKING CONDITIONS HAVE BEEN REDUCED AND A...
Read full bulletin
MISMATCH OF INFORMATION OF THE TRAILER BRAKE CONTROL SYSTEM DETERMINES AMOUNT OF REQUIRED BRAKING. MODEL 2010 SILVERADO HD 2500/3500, SIERRA HD 2500/3500. *PE
GM: DURING BRAKE INSPECTIONS THERE HAVE BEEN SOME HAIRLINE CRACKS ON THE BRAKE PADS.
Read full bulletin
*RM
Software & Calibration
18 bulletinsVehicle Software Enhancements
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
OnStar Voice Fallback Number Update
This Preliminary information communicatesof a program update to fix a bump when stopping
This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor...
Read full bulletin
operation information.
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation...
Read full bulletin
Information and Transaction Submissions Procedure and general content updates.
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor...
Read full bulletin
Operation.
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor...
Read full bulletin
Operations.
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor...
Read full bulletin
operations.
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor...
Read full bulletin
Operation.
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation...
Read full bulletin
under Courtesy Transportation Warranty Transaction Submission.
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
This preliminary informational bulletin provides a revision of PI0718A to add model years and update the Warranty...
Read full bulletin
Information.
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for...
Read full bulletin
electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for...
Read full bulletin
electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK.
Read full bulletin
*RM UPDATED 12/6/11. *PE
Lighting
15 bulletinsThis informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
SES Light Rough Running And/Or Lack Of Power.
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
Computer-Controlled Cranking System (Bump Start) Inoperative.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
Computer-Controlled Cranking System (Bump Start) Inoperative.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation...
Read full bulletin
settings for concernc regarding noice drop outs during calls and muffled sound.
This informational bulletin provides the proper information used to determine the road force variences within new tires...
Read full bulletin
being installed and the proper forms used to send the tires back if the road force is not within spec.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicle's odometer appears...
Read full bulletin
to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
HVAC & Climate
8 bulletinsDiagnosis and Repair HVAC Blower Function.
A/C Blows Warm Or Poor Performance.
Reduced Heater Performance with Winter Grille Cover Installed
This technical bulletin provides a procedure to correct a customer concern of reduced heater performance with winter...
Read full bulletin
grille cover installed.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This technical bulletin provides repair information for the correction of a customer concern of short duration musty...
Read full bulletin
odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom...
Read full bulletin
Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG...
Read full bulletin
PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
Suspension
8 bulletinsRattle Squeak Clunk Bump Noise From Front Suspension.
Rattle Squeak Clunk Bump Noise From Front Suspension.
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak...
Read full bulletin
noise from the metals making contact.
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers...
Read full bulletin
concern of a squeaking noise from the rear suspension.
This technical bulletin provides a procedure for retorque the lead springs.
This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer...
Read full bulletin
concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps.
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that...
Read full bulletin
has a fluid residule from a possible external source from a leaking shaft seal.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR...
Read full bulletin
VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.
Steering
5 bulletinsVarious Concerns Related To The IP Backlighting Cruise Control Steering Wheel Controls Horn.
Various Concerns Related To The IP Backlighting Cruise Control Steering Wheel Controls Horn.
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise...
Read full bulletin
or fluid leak concern that is caused during extremely low temperatures.
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise.
Read full bulletin
Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
Air Bags & Safety
3 bulletinsThis service bulletin provides information on Takata Air Bag Courtesy Transportation Reimbursement Program - Applicable...
Read full bulletin
to GM Recalls listed in bulletin.
This service bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM...
Read full bulletin
Recalls 14491, 14735,15040, 15041, 15043,15044, 15045, 15046, 15406,15438, 15442, 15815, 15816,15817, 15818, 15826, 17009, 17476, 17477, 28810, 28811,17478, 18015, N192273760, N192278940, N212328760, N212328770, N212328780, N212328790, N212328800, N242437050, N242437060, N242437070.
This service bulletin provides information on availability for a seat belt extender.
Hybrid & EV
1 bulletinHybrid No Crank or Loss of High Speed Communications.