2017 Gmc Sierra 2500 TSBs
880 Technical Service Bulletins across 17 categories
Categories
Engine
253 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This Preliminary information communicates information on adding RPO UF3 Fast Idle to a vehicle.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Preliminary information communicates to the dealer technician to reference the electronic parts catalog to check...
Read full bulletin
the EGR valve part number that was installed.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument...
Read full bulletin
Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection dropped, the radio station or volume changes when operating the snow plow. Please advise the customer that engineering is aware of this concern and working on this issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for after installation of a replacement upper valve body, the transmission...
Read full bulletin
may have no Reverse and no 2nd gear.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head...
Read full bulletin
gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary information communicates diagnostic aid to help isolate possible repeat thermal by-pass valve concern.
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head...
Read full bulletin
gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not.
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause.
This informational bulletin provides information on 6.6L Duramax Possible Oil Leak Path Information.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This informational bulletin provides information for the technicians on where to look on the Duramax engine for coolant...
Read full bulletin
leaks.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
Informational bulletin explaining how a plow may cause overheating and engine damage when traveling over 45 mph.
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal...
Read full bulletin
operation and no parts should be replaced for these normal operating conditions.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through...
Read full bulletin
failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional...
Read full bulletin
engine-block heater cord, may have a condition in which the block heater cable function was disabled. Dealers will replace the engine block heater and cord.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary Information communication provides information to the technician about vehicles that the blower motor...
Read full bulletin
may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator.
This service bulletin provides diagnostic information for a customer concern of engine vibration.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator.
This service bulletin provides diagnostic information for a customer concern of engine vibration.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this...
Read full bulletin
occurrence.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
Hesitation, Stalling, Engine Speed Flare While Coasting, Unintended Acceleration Feel During a Parking Lot Maneuver,...
Read full bulletin
Reduced Surge in Low Speed Maneuvers, Stumble, Harsh Tip-In/Tip-Out, Park-Reverse-Drive Shift Concerns, Harsh Shifts, Erratic Shifts, Engine Vibration, Vibration, Buzz and/or Humming from Steering Wheel, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0097, P054F, P24B1, P24C7, P0128, P2BAA, P2635, P11CC, P10D1, P0483, P2636, P0181, P22FE, P0263, P0266, P0269, P0272, P0275, P0278, P0281, P0284, P040C, P040D, P041C, P041D Set Cause This condition may be caused by an anomaly in the Engine Control Module (ECM) and the Transmission Control Module (TCM). Note: It is important that both the ECM and TCM are updated to the latest software. Not updating both modules may result in additional undesired vehicle performance. If the ECM and TCM have the latest calibrations, refer to SI for the DTC set or existing condition. Validate the ECM and TCM have the latest software calibration. If the ECM and TCM are not at the latest calibration, using TIS2Web, select (K20/K71) Engine and Transmission Control Module. ⇒ Both modules must be reprogrammed sequentially to the latest software calibration available. If the modules have the latest calibrations, refer to SI for the DTC set.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This informational bulletin provides information for the technicians on where to look on the Duramax engine for coolant...
Read full bulletin
leaks.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin provides information on 6.6L Duramax Possible Oil Leak Path Information.
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated.
This informational bulletin provides information on higher than expected oil consumption.
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal...
Read full bulletin
operation and no parts should be replaced for these normal operating conditions.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This technical procedure provides a procedure to replace the front oil crank seal on remanufactured engines only, if...
Read full bulletin
found the cause of the customers concern.
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through...
Read full bulletin
failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information and definitionsto the technician about vehicles that...
Read full bulletin
have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information and definitionsto the technician about vehicles that...
Read full bulletin
have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians arereferred toTorque Converter Diagnosis in SI.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
Customer Satisfaction Program - Certain vehicles equipped with the 6.6l Duramaxdiesel engine (RPO L5P) and optional...
Read full bulletin
engine-block heater cord, may have a condition in which the block heater cable function was disabled. Dealers will replace the engine block heater and cord.
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin...
Read full bulletin
has been sheared away to correct a crank/No Start condition.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
Customer Satisfaction Program - Certain vehicles equipped with the 6.6l Duramaxdiesel engine (RPO L5P) and optional...
Read full bulletin
engine-block heater cord, may have a condition in which the block heater cable functionwas disabled. Dealers will replace the engine block heater and cord.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not.
This engineering information bulletin ends the need for information from the field on an Intermittent No Forward and/or...
Read full bulletin
No Reverse While Driving condition. If this condition is encountered, refer to SI for further diagnosis.
This engineering informational bulletin is requesting information on a scraping noise heard from under the vehicle while...
Read full bulletin
driving.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal...
Read full bulletin
operation and no parts should be replaced for these normal operating conditions.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
N192264210 - Customer Satisfaction Program - Certain vehicles may have a condition in which the block heater cable function was disabled.
Read full bulletin
Dealers will replace the engine block heater and cord.
N182202780 01 - Special Coverage.
Read full bulletin
Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This preliminary information explains that there are differences between the Elevated Idle, PTO and High Idle options.
N182198000 - Special Coverage Adjustment - Certain vehicles, equipped with a 5.3L or 6.2L engine, may have a condition...
Read full bulletin
which affects fuel injector function. Under certain circumstances one or more of the vehicle?s fuel injectors may deliver an improper amount of fuel to the engine. If this occurs, the Malfunction Indicator Lamp (Check Engine Light) will illuminate, the engine may idle or run rough, and the vehicle may stall. A diagnostic trouble code related to the fuel injector may be set. This special coverage only applies to vehicles in these states: California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington. Dealers are to replace the fuel injectors as necessary. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and...
Read full bulletin
P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about vehicles that are equipped with...
Read full bulletin
6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin provides information on higher than expected oil consumption.
This informational bulletin provides information on common diesel engine tick noises and how they are considered part of...
Read full bulletin
normal operation and no parts should be replaced for these conditions.
17357 and 17366 - Service update.
Read full bulletin
General Motors has released four field actions related to a condition in which certain vehicles may have an incorrect torsion bar built into the front seat belt retractors. Vehicles in dealer new inventory were placed on stop delivery earlier this month and the field actions were released as parts become available. This message is being sent to provide a summary of the status of these field actions. Part Numbers - An issue has been reported that some of the belt kit part numbers listed in these bulletins may not be listed in EPC. This makes it difficult to identify which part number to install on the vehicle. We are quickly working to remedy this situation. Until the correction is completed, dealers should verify part number progressions utilizing their parts system resources prior to reaching out for additional assistance. We apologize for this inconvenience and hope to have it corrected soon. Service Update Bulletin 17357 - Applies to certain vehicles. The total number of U.S. vehicles involved is approximately 14,483. Dealers will replace the Monroney label. Bulletin 17357 was released to dealers on 9/6. If you have not received a replacement window label for a vehicle in dealer new inventory, please request a replacement using the process given in the bulletin. Service Update Bulletin 17366 - Applies to certain vehicles. The total number of U.S. vehicles involved is approximately 345. Dealers will replace seat belt retractors in first row driver and passenger position with correct parts. Bulletin 17366 was released to dealers on 9/22. The parts pre-ship has completed and dealers should begin receiving parts now.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire.
Read full bulletin
This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production...
Read full bulletin
Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about the Upfitters questions about...
Read full bulletin
installing aftermarket electrical accessories. Dealer should reference the latest version of General Motors Upfitter Integration Bulletin 115 for this information. It can be found at http://www.gmupfitter.com.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise.
Read full bulletin
Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being...
Read full bulletin
overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production...
Read full bulletin
Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner's Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
This Preliminary Information communication provides information to the technician that a whine noise heard from the...
Read full bulletin
automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that a customer may request the...
Read full bulletin
factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician about the text messaging feature on...
Read full bulletin
some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
N182188930 - Special Coverage.
Read full bulletin
Some vehicles, equipped with a Duramax Diesel engine, the transmission cooler lines may be rubbing on the front frame/bumper mount bracket. This condition could cause the cooler lines to leak. Transmission fluid may be seen on the ground under the front bumper. Some drivers may have difficulty selecting gears or experience transmission slip. This special coverage covers the condition described above for a period of 6 years or 72,000 miles (116,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to replace the transmission cooler lines. The repairs will be made at no charge to the customer.
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary Information communication provides information to the technician about vehicles that have not...
Read full bulletin
engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.
This engineering informational bulletin is requesting information from the dealers on vehicles that have the condition...
Read full bulletin
of a malfunction indicator lamp illuminated.
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition...
Read full bulletin
of Malfunction Indicator Lamp Illuminated with DTCs P0335, P0340, or P0365 Set.
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL on.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of...
Read full bulletin
Malfunction Indicator Lamp Illuminated with One or More Glow Plug Control DTCs Set.
This engineering information is ending the need for information from the field on vehicles that have the condition of...
Read full bulletin
Check Engine Light, Delayed Shifts and/or Transmission Stuck in Gear with DTC P0751, P0752, P0756, P0757, P0761 or P0762 Set.
This Technical bulletin provides information on new software to correct a hesitation, chuggle, fishbite or roughness...
Read full bulletin
that can be felt in gear ranges 3rd - 6th gear V8 mode, TCC locked, low RPMs (1200 &-1300 when tipping into throttle to load engine.
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of...
Read full bulletin
a MIL or a engine misfire due to a loose spark plug wire.
This engineering information bulletin ends the need for information from the field on vehicles that have the condition...
Read full bulletin
of the Air bag light illuminated and SIR codes set within the SIR module.
This informational bulletin provides information on higher than expected oil consumption.
This informational bulletin provides information on common diesel engine tick noises and how they are considered part of...
Read full bulletin
normal operation and no parts should be replaced for these conditions.
This preliminary information explains that there are differences between the Elevated Idle, PTO and High Idle options.
This Preliminary Information communication provides information to the technician about vehicles that have a check engine light on.
Read full bulletin
Technician may find Diagnostic Trouble Code P026A. The owner's manual advises not to drive above 45 MPH with a snowplow installed.
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire.
Read full bulletin
This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode,...
Read full bulletin
and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
This Preliminary Information communication advises the technician that the 6.6L Diesel Engine exchange program has...
Read full bulletin
ended.
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument...
Read full bulletin
Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection dropped, the radio station or volume changes when operating the snow plow. Please advise the customer that engineering is aware of this concern and working on this issue.
This Preliminary Information communication provides information to the technician about vehicles that are equipped with...
Read full bulletin
6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This Preliminary information communicates information on ahydrauilc rush type noise from the power steering gear.
Read full bulletin
This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
This Preliminary Information communication provides information to the technician about the text messaging feature on...
Read full bulletin
some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY...
Read full bulletin
GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER,...
Read full bulletin
RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL...
Read full bulletin
TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE...
Read full bulletin
WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER...
Read full bulletin
DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL...
Read full bulletin
ENGINE DAMAGE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE...
Read full bulletin
GASKET SEALING SURFACES.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF...
Read full bulletin
AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
Pre-Delivery & Maintenance
157 bulletinsThis service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information to the customer about the rear camera guidelines not being present at times...
Read full bulletin
due to the VBM taking over the rear camera option.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides information for dealers/technicians on Over the Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides information to the customer about the rear camera guidelines not being present at times...
Read full bulletin
due to the VBM taking over the rear camera option.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides service information for a DEF pump that is unable to build pressure after replacement.
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front...
Read full bulletin
grille or radiator area.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles...
Read full bulletin
that may not pass California smog inspection or smog inspection in other states.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This warranty administration bulletin provides policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides policy information with the field action courtesy transportation policy.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON...
Read full bulletin
VEHICLES ORIGINATING/SOLD IN CANADA.
Other
107 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up...
Read full bulletin
on the glow plug causing a premature failure.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up...
Read full bulletin
on the glow plug causing a premature failure.
This informational bulletin provides information to the customer about the rear camera guidelines not being present at...
Read full bulletin
times due to the VBM taking over the rear camera option.
This Preliminary information communicatesinformation on how dealers can contact the supplier for Associated Accessories...
Read full bulletin
offered through GM.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
Information.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This technical provides a procedure to check for a possible faulty Reductant Injector and replace if the cause of the...
Read full bulletin
customers concern.
This technical bulletin provides a procedure for the technician to check and tighten the CAC plumbing if found loose.
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Preliminary information communicatesinformation on how dealers can contact the supplier for Associated Accessories...
Read full bulletin
offered through GM.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
Customer Satisfaction Program Closed Message sent.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
This technical bulletin provides a procedure to reset the DTCs and take the vehicle for a test drive to verify the codes...
Read full bulletin
do not return.
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or...
Read full bulletin
Fluctuate, No Crank, Start then Stall.
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or...
Read full bulletin
Fluctuate, No Crank, Start then Stall.
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin explains how to check the NOx Catalyst Reductant-Load Adaptive Values using GSD2.
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage.
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.
This technical bulletin advised the technician to take the vehicle for a test drive to validate a possible normal TCC...
Read full bulletin
performance while under heavy specific driving maneuvers.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesPossible Crank no start or extended crank with DTC p12A6 set current or...
Read full bulletin
history.Under Investigation
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
This Preliminary information communicates the possibility of dtc P12A6 with the possibility of a crank no start or...
Read full bulletin
extended crank concern.
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate.
Read full bulletin
Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
This Preliminary information communicates the possibility of dtc P12A6 with the possibility of a crank no start or...
Read full bulletin
extended crank concern.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
N172118130 Stop Delivery population revision.
Read full bulletin
On September 1, 2017, GM ordered a stop delivery of certain vehicles in new vehicle inventory. Additional vehicles have been added to this stop delivery order. The revised list provides the Vehicle Identification Number (VIN) of all involved vehicles in dealer new inventory. Until further instructions are received, involved vehicles that are in dealers? possession (new vehicle inventory) must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration purposes or any other dealer use. Instructions for releasing the involved vehicles from this stop delivery will be provided in phases in the near future.
N172118130 Stop Delivery.
Read full bulletin
On September 1, 2017, GM ordered a stop delivery of certain vehicles in new vehicle inventory. Additional vehicles have been added to this stop delivery order. Until further instructions are received, involved vehicles that are in dealers? possession (new vehicle inventory) must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration purposes or any other dealer use. Instructions for releasing the involved vehicles from this stop delivery will be provided in phases in the near future.
N172118130 Stop Delivery.
Read full bulletin
Effective immediately, stop the delivery of certain vehicles in new vehicle inventory. We are investigating an issue relating to the accuracy of the New Car Assessment Program (NCAP) ratings on the Monroney label for these vehicles. Until further instructions are received, involved vehicles that are in dealers? possession (new vehicle inventory) must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration purposes or any other dealer use. We are working to finalize the investigation as quickly as possible. When the investigation is complete, further instructions will be released.
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or...
Read full bulletin
click type noise while driving.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary information communicatesContent Theft Deterrent RPO UTJ is included and only available with Remote Vehicle Start RPO BTV.
Read full bulletin
If the vehicle is not equipped with Remote Vehicle Start RPO BTV the vehicle will not have Content Theft Deterrent.
This Preliminary Information communication advises the technician this vibration or growl noise can be difficult to...
Read full bulletin
diagnose and using the Pico Scope is recommended for diagnosing this concern. Customers has vibration or growl noise between 45-65 Miles-per-hour.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or...
Read full bulletin
pixelated
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage.
This informational bulletin provides explanation of a normal condition of a loose fitting ball receiver in the...
Read full bulletin
gooseneck.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This preliminary bulletin provides additional guidance for diagnosing vibrations or disturbances that may occur on SUVs...
Read full bulletin
and how to correct and repair.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This Preliminary information communicates to the dealer technician how to diagnose for a possible damaged or broken...
Read full bulletin
pushrod.
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity.
Read full bulletin
Technician should check the Regular Production Option Code list for (VV4).
This Preliminary information communicates to the dealer technician how to diagnose for a possible damaged or broken...
Read full bulletin
pushrod.
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key...
Read full bulletin
Fob or OnStar Mobile Application and where to locate the information for future use.
This Preliminary Information communication provides information to the technician about vehicles that have water or dust...
Read full bulletin
from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers...
Read full bulletin
memory position.
This informational bulletin provides information on a new U.S.
Read full bulletin
dealer special tool loan program.
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to...
Read full bulletin
properly disable the SIR system for repairs at or near
This Preliminary Information communication advises the technician this vibration or growl noise can be difficult to...
Read full bulletin
diagnose and using the Pico Scope is recommended for diagnosing this concern. Customers has vibration or growl noise between 45-65 Miles-per-hour.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES.
Read full bulletin
GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS...
Read full bulletin
LESS THAN 10,000 MILES ON IT.
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING...
Read full bulletin
INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT.
Electrical
97 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors...
Read full bulletin
if found the cause of the MIL.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors...
Read full bulletin
if found the cause of the MIL.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors...
Read full bulletin
if found the cause of the MIL.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals...
Read full bulletin
but allow time for the sensor to thaw.
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the...
Read full bulletin
customers concern.
This Preliminary Information communication provides information to the technician with the correct way to remove the...
Read full bulletin
front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
This Preliminary Information communication provides information to the technician with the correct way to remove the...
Read full bulletin
front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical...
Read full bulletin
connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage...
Read full bulletin
detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of...
Read full bulletin
Loss of Steering Assist due to a software abnormality.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage...
Read full bulletin
detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the...
Read full bulletin
customers concern.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
Changing to Camper Outside Rearview Mirrors Some customers may request to have camper style mirrors installed on their vehicle.
Read full bulletin
The new electrical architecture for the Silverado and Sierra has made swapping mirrors a more involved procedure than with previous models. The recommendation has been divided into three upgrades, depending on which mirrors the truck was built with (RPO DE2, DL8 or DL3). Please follow the correct RPO group below, because not all camper mirrors can be installed on all trucks. After selecting the correct RPO mirror the truck was built with, this PI will aid in determining which camper mirrors can be installed.
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct...
Read full bulletin
battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
Malfunction Indicator Lamp Illuminated (MIL) - DTC P2635 and/or P018B Set In High Ambient Temperatures With Hesitation,...
Read full bulletin
Surging and Stalling Condition Some customers may comment that the Malfunction Indicator Light (MIL) is illuminated. Some customers may also comment on one or more of the following symptoms: Hesitation Surging Stalling Note: In ambient temperatures 100 F (37.7 C) degrees or higher, DTCs P2635 and/or P018B may set. The Technician may find one or more of the following DTCs set: P2635 P018B Cause This condition may be caused by a vapor buildup in fuel feed line. Correction If the conditions stated above are met, replace the fuel pump module with an updated version
Diagnostic Tip for Malfunction Indicator Lamp (MIL) Illuminated - DTC P249D, P249E, U029D, U029E Set Some customers may...
Read full bulletin
comment that the MIL is illuminated. The technician may find one or more of the following DTCs set: U029D U029E P249D P249E Note: The graphic above depicts an example of a torn and missing seal. Moisture intrusion past a damaged (1) seal located in the connector for the NOx sensor wiring harness. Missing (2) seal located in the connector for the NOx sensor wiring harness. Correction If you encounter a vehicle with the above concern, perform normal diagnostics for the codes set. ⇒ If diagnostics lead to NOx sensor replacement, inspect the mating chassis electrical connector for corrosion. Clean and repair as necessary.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This Preliminary Information communication provides information to the technician about vehicles that are found to have...
Read full bulletin
a back-up alarm inoperative during the Pre-Delivery Inspection. On trucks equipped with the Back Up Alarm (RPO 8S3), the alarm will be intentionally left disconnected from the assembly plant. Technician will reroute the harness and plug it in.
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the...
Read full bulletin
customers concern.
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical...
Read full bulletin
connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals...
Read full bulletin
but allow time for the sensor to thaw.
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the...
Read full bulletin
customers concern.
This technical bulletin provides a procedure to program the ECM if found the cause of the customers complaint.
This technical bulletin provides a procedure to update the GPCM if found the cause of the customers concern.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage...
Read full bulletin
detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to...
Read full bulletin
the vent and route down the fuel feed line and secure with zip ties.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This technical bulletin provides repair information to correct a customer concern of Action Required Steering Assist is...
Read full bulletin
Reduced Drive with Care Or Service Power Steering Message And Or Current Power Steering Control Module DTCs.
This Warranty Administration Bulletin Provides High Voltage Battery Exchange Process Information.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to...
Read full bulletin
the vent and route down the fuel feed line and secure with zip ties.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This Preliminary information communicates a customer concern ofIPC gauges inoperative or fluctuate, No Start,No...
Read full bulletin
Crank,SIR Light / Service Airbag Message, Service Suspension Message,Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback,HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164,U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.
This Preliminary Information communication provides information to the technician about vehicles that have a low voltage...
Read full bulletin
reading on the volt gauge during the first several minutes after a cold start. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This informational bulletin provides information on a Service Emission System Message and/or a Malfunction Indicator Lamp illuminated.
Read full bulletin
This usually occurs after recently filling the DEF tank with the ignition in the on position due to some DEF fill equipment uses pumps that create a high level of temporary aeration of the DEF fluid being dispensed in the tank.
This Preliminary information communicates to the dealer technicians that the glow plug control module software needs to...
Read full bulletin
be updated anytimg a glowplug is replaced.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This technical bulletin provides a procedure to program the ECM if found to be the cause of the customers concern.
This Preliminary Information communication provides information to the technician about the Media Oriented Systems...
Read full bulletin
Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician with the correct way to remove the...
Read full bulletin
front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
This Preliminary Information communication provides information to the technician about vehicles that may have a...
Read full bulletin
diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna...
Read full bulletin
malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.
This Technical bulletin provides a procedure for radio replacement due to the radio tuner module being bad.
This technical bulletin provides a procedure to reprogram the ECM and TCM to the latest calibrations to correct the...
Read full bulletin
concerns.
This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of...
Read full bulletin
Loss of Steering Assist due to a software abnormality.
This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the...
Read full bulletin
front camera module.
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
This technical bulletin has a procedure to reprogram the HPCM to to correct the customers concern.
This Technical bulletin provides information on new software for the ECM due to DTC P228D causing the MIL to illuminate.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including...
Read full bulletin
Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of Rear Camera Gridlines, Service Rear Vision System Message, Radio Turns On Unwanted At Startup, and/or Navigation Radio Destination State Defaults To WV, Intermittent Radio/display Resets, Volume Control Inoperative.
This Technical Bulletin involves technicians clearing Lost Communication U Codes from modules due to false setting of...
Read full bulletin
the DTC.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This Preliminary Information communication provides information to the technician about vehicles that may have a...
Read full bulletin
diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
This Preliminary Information communication provides information to the technician about vehicles that have installed an...
Read full bulletin
aftermarket bed cap or topper may question where they can wire in the center high mounted stop light for the cap or topper. Provisions for the center high mounted stop light have been provided at the Rear Body Junction Block (X63A) connector X6 terminal 1 for 2014-2015 model years. For vehicle model years 2016-2017 provisions for the center high mounted stop light have been provided at connector X400 terminal 4, circuit 1054.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
This Preliminary Information communication provides information to the technician about vehicles that in the radio...
Read full bulletin
settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
This Preliminary Information communication provides information to the technician about vehicles that in the radio...
Read full bulletin
settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required...
Read full bulletin
additional information.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED...
Read full bulletin
TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE,...
Read full bulletin
IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
Fuel System
51 bulletinsThis warranty administration bulletin provides policy information on vehicles outside of a California Emissions State...
Read full bulletin
who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This bulletin provides information on how to look for and test for DEF or water in the fuel system and what the specs...
Read full bulletin
should be.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides information on availability of Diesel Fuel additives.
This Preliminary Information communication provides information to the technician about vehicles that may have a bump...
Read full bulletin
feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides information on availability of Diesel Fuel additives.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information on availability of Diesel Fuel additives.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in...
Read full bulletin
performance in regards to the customers concerns.
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the...
Read full bulletin
cause of excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
This technical bulletin provides a procedure to replace the fuel tank and internal parts if found expanding and...
Read full bulletin
contacting the drive shaft.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This Informational Bulletin provides information on availability of Diesel Fuel additives.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
THis informational bulletin advises the tech of a possible plugged fuel breather vent and how to add a vent breather...
Read full bulletin
line to correct the customers concern.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the...
Read full bulletin
part and ordering it from the EPC.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the...
Read full bulletin
fuel system caused by a failed part.
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust...
Read full bulletin
Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
This Preliminary information communicates to dealer technicians to refer to service update bulletinN182179090 for 2018...
Read full bulletin
model vehicles and to use labor operation4029959 Emissions - Customer Concern Not Duplicated (CCND) for 2017 model year vehicles with DTC P140B setting.
This Preliminary information communicates to dealer technicians to refer to service update bulletinN182179090 for 2018...
Read full bulletin
model vehicles and to use labor operation4029959 Emissions - Customer Concern Not Duplicated (CCND) for 2017 model year vehicles withDTC P140B setting.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
Transmission
44 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to...
Read full bulletin
transmission installation.
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the...
Read full bulletin
t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or...
Read full bulletin
transmission leaking ATF causing the customers concern.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare...
Read full bulletin
after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if...
Read full bulletin
no problem was found, to replace the tbv.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC)...
Read full bulletin
guidelines are temporarily not available at times but the RVC will remain on during the concern. Additionally, no related DTCs will be found if this bulletin applies. One example of when this concern may be observed is if a customer quickly starts the car and immediately places the shifter in Reverse while the infotainment system is still in the initial boot up process. Cause This is a result of the RVC image being provided via an alternate robust RVC feed from the Video Bypass Module (NGI systems) or from the radio (BYOM2 and Info 3.0 systems). This alternate robust RVC feed is provided in the event that the primary RVC feed is not available for any reason just to ensure that the RVC image is always present when in reverse. Correction If this concern is experienced and no related codes are present, DO NOT replace any parts as it is normal for the RVC guidelines not to be present when the RVC image being displayed is from the alternate robust RVC feed. If this occurs after quickly starting the vehicle and immediately placing the shifter in Drive, the RVC guidelines can be displayed again in most cases if they are really needed by safely coming to a stop, placing the transmission in Park for a moment, and then shifting to Reverse again.
This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start...
Read full bulletin
up conditions when the clutch packs are full of residual oil.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing...
Read full bulletin
each scenario and documenting findings. This technical bulletin provides a procedure to install dust deflectors when replacing wheel bearings on vehicles no matter what the concern is of the vehicle. This technical bulletin provides a procedure to reprogram the TRCM to correct the customers concern of the Service Transmission and MIL on. This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the front camera module.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or...
Read full bulletin
shudder during a light throttle acceleration between 48 and 104 KM/H (30 and 65 MPH) at a steady state.
This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair...
Read full bulletin
steering that feels loose or has excessive play. This concern could be caused by the Pitman Shaft Over-Center Preload Adjustment becoming misadjusted. Technician will need to replace the steering gear pitman arm shaft with an updated design.
THIS TECHNICAL BULLETIN PROVIDES THE PROCEDURES TO COMPLETE A TRANSSMISSION ADAPTIVE LEARN ON ALL THE DIFFERENT TYPES OF...
Read full bulletin
VEHICLES AND TRANSMISSIONS BASED ON RPO OPTIONS TO CORRECT A CONDITION OF HARSH SHIFTS ON HARD ACCELLERATIONS.
Body & Paint
36 bulletinsThis PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame...
Read full bulletin
Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.
This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame...
Read full bulletin
Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information on Paintless Dent Repair Process.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and...
Read full bulletin
that it is considered a normal condition.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This technical bulletin provides repair information to correct a customer concern of hearing excessive wind noise from...
Read full bulletin
front side door glass area.
This informational bulletin provides information for assisting the customer in setting the position for the memory...
Read full bulletin
mirror and the reverse tilt
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
Tires & Wheels
33 bulletinsThis Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This informational bulletin provides information on Wheel Balancer Mounting Instructions.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This service bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to...
Read full bulletin
prime the pump.
The complete Communication ID is: RFI20210526_939-187 and was communicated to customers on May 26, 2021.
Read full bulletin
The Communication ID field did not permit me to enter the complete Communication ID as it is in our internal system. This product is a steel wheel. The customer communication requested return of unsold inventory to inspect the wheel for material dimension. If the material fails to meet the manufacturing specification, the wheel may not perform as expected. If the wheels are not returned, then warranty rate may increase. This product affects the following vehicles: 2011-2019 Chevrolet Silverado 2500HD & 3500HD, 2011-2019 GMC Sierra 2500HD & Sierra 3500HD.
This informational bulletin provides information on Wheel Balancer Mounting Instructions.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks...
Read full bulletin
and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for...
Read full bulletin
GM Vehicles.
This SKU is a Tire Hoist Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect for the shape of the centerpiece of the tire hoist being round when it should be square. If the centerpiece is the incorrect shape then the tire hoist cannot be operated with the OE tools, and the end user would therefore not be able to lower the spare tire with the vehicles original tools.
This informational bulletin provides information for 22" accessory wheel/tire usages.
This Preliminary Information communication provides information to the technician on how to diagnose vehicles with...
Read full bulletin
various noises associated with four wheel drive operation. Before beginning any diagnosis it is imperative to review the Symptoms - Transfer Case in Service Information and perform the necessary inspections. In all cases the complaint vehicle should be compared to another like vehicle before beginning any repairs.
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will...
Read full bulletin
replace it via the website provided.
This informational bulletin provides information on the temporary tire flat spotting condition.
This Preliminary Information communication provides information to the technician about vehicles that the enter caps on...
Read full bulletin
chrome or polished aluminum wheels are missing or came off while driving. Technician will need to install the center caps by pressing the chrome center cap onto the wheel until an audible “click” is heard.
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and...
Read full bulletin
balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT...
Read full bulletin
EQUIPMENT.
Lighting
26 bulletinsThis preliminary information communicates an issue with aftermarket LED headlights causing IPC warning messages and MIL...
Read full bulletin
along with several low speed lan DTCs.
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This technical bulletin provides a procedure to correct the condition of Malfunction Indicator Lamp Illuminated with...
Read full bulletin
DTCs P2463 P2459 P11FB P11D3.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary information communicates to dealers of a known issue with failed map update
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicle's odometer appears...
Read full bulletin
to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ENABLE THE 4G LTE WIFI ON NEWLY DELIVERED VEHICLES FOR SOME VEHICLES...
Read full bulletin
THAT WERE NOT SHIPPED WITH THE FEATURE NOT ENABLED.
Brakes
22 bulletinsThis Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full...
Read full bulletin
Turns.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need...
Read full bulletin
to be replaced if the brake pedal moves or applies on its own at a full turn.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise...
Read full bulletin
from brakes, uneven front brake pad wear.
This technical bulletin provides a procedure for pad replacement due to on premature and/or uneven brake pad wear.
Certain vehicles, may have incorrect language in the Forward Auto Braking (FAB) section of the owner manual which...
Read full bulletin
states, ?If the vehicle has Forward Collision Alert (FCA), it also has FAB which includes Intelligent Brake Assist (IBA)?. This statement is correct for light duty trucks but the heavy duty models only have the Forward Collision Alert. Customer to receive an owner manual insert. Dealers are to print and install the owner manual insert on unsold vehicles.
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need...
Read full bulletin
to be replaced if the brake pedal moves or applies on its own at a full turn.
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or...
Read full bulletin
Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
This Preliminary Information communication provides information to the technician about vehicles that have a Shudder,...
Read full bulletin
bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Technician will need to measure the actual truck and trailer weights, with the trailer loaded to the point that exhibits the condition. If any weight parameter is exceeded such as the Front Gross Axle Weight Rating, Rear Gross Axle Weight Rating, Gross Vehicle Weight Rating, or Gross Combined Weight Rating the load must be reduced before investigating further. If evaluation of the trailer’s brakes indicates trailer brake capability is adequate, adjust brake controller per the Trailer Gain Adjustment Procedure described in the Driving and Operating section of the Owner’s Manual and evaluate truck and trailer combination for braking shudder.
This Preliminary Information communication provides information to the technician about vehicles that have Trailer...
Read full bulletin
connection not recognized or “Check Trailer wiring” or “Service Trailer Brake” message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the battery and Trailer Brake Power Module connector for corroded terminals and replace as necessary.
Infotainment
17 bulletinsThis service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions...
Read full bulletin
equipped with IOB Radio.
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a...
Read full bulletin
vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
This technical bulletin provides repair information to correct a customer concern of infotainment screen appearing too...
Read full bulletin
bright at night.
This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at...
Read full bulletin
Times After Being Turned Off in Settings and no parts should be replaced due to this condition.
This technical bulletin provides a procedure to replace the radio for vehicles with the condition of Intermittent Pop...
Read full bulletin
Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.
This Technical bulletin provides information on new software to correct the rear camera display being too bright.
N172118130 Stop Delivery population revision.
Read full bulletin
On September 1, 2017, GM ordered a stop delivery of certain vehicles in new vehicle inventory. Additional vehicles have been added and some vehicles have been removed from this stop delivery order. The revised list provides the Vehicle Identification Number (VIN) of all involved vehicles in dealer new inventory. Important: This revision 03 was necessary because some vehicles were discovered in the list that should have been transferred to the population of SUB 17357. The involved vehicles have now been transferred to SUB 17357. In addition to the attached revised list, you may reference the Investigate Vehicle History (IVH) screen in the GWM system.Until further instructions are received, involved vehicles that are in dealers? possession (new vehicle inventory) must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration purposes or any other dealer use. Instructions for releasing the involved vehicles from this stop delivery will be provided in the near future.
This Preliminary information communicates repair information for therear vision camera or surround vision camera image...
Read full bulletin
being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not...
Read full bulletin
function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
This technical bulletin provides a procedure to replace the media player for conditions of Rear Seat Entertainment (RSE)...
Read full bulletin
Audio and Video Out of Sync When Playing a Movie due to an internal calibration concern.
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack...
Read full bulletin
for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
This Technical bulletin provides information on new software to correct the rear camera display being too bright.
This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or...
Read full bulletin
Apple Carplay.
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar.
Read full bulletin
Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
This Preliminary Information communication advises the technician that vehicles with front seat Regular Production...
Read full bulletin
Option Codes A52, AZ3, or B3F may comment about low treble, or excessive bass from the front door speakers. This is a normal design characteristic for this seat configuration. These vehicles lack a subwoofer.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO...
Read full bulletin
VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
Air Bags & Safety
8 bulletinsThis Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
This service bulletin provides information on availability for a seat belt extender.
The drivers and front passengers seat belt retractors in certain 2017 model year Chevrolet Silverado Heavy Duty (2500...
Read full bulletin
and 3500 Series) and GMC Sierra Heavy Duty (2500 and 3500 Series) vehicles may have been built with different torsion bars than were used in testing the vehicles for the Government 5- Star Safety Ratings listed on the window sticker. While these vehicles comply with all applicable government safety standards, this condition may affect the Government 5-Star Safety Ratings listed on the window sticker. Correction Customers have the choice of whether to have this replacement performed. If the customer chooses to have it completed, dealers are to replace the driver and front passenger-side seat belt retractor assemblies with assemblies containing the correct torsion bar.
The drivers and front passengers seat belt retractors in certain 2017-2018 model year Chevrolet Silverado Heavy Duty...
Read full bulletin
(2500 and 3500 Series) and GMC Sierra Heavy Duty (2500 and 3500 Series) vehicles may have been built with different torsion bars than were used in testing the vehicles for the Government 5-Star Safety Ratings listed on the window sticker. While these vehicles comply with all applicable government safety standards, this condition may affect the Government 5-Star Safety Ratings listed on the window sticker. Correction Customers have the choice of whether to have this replacement performed. If the customer chooses to have it completed, dealers are to replace the driver and front passenger-side seat belt retractor assemblies with assemblies containing the correct torsion bar.
Customer Satisfaction Program - Certain vehicles that had the front passenger seat cushion frame previously replaced,...
Read full bulletin
may not have had the adjuster stops transferred and are missing on the replacement part. The front passenger seat may be in a position beyond the occupant design travel range.Dealers are to inspect the front passenger seat tracks for the presence of both adjuster stops and install missing adjuster stops if necessary.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS...
Read full bulletin
REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY...
Read full bulletin
SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET.
HVAC & Climate
8 bulletinsThis service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
Block Heater Restore
This technical bulletin provides a procedure to install a pice of foam between the heater core pipes to correct the...
Read full bulletin
customers concern.
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative...
Read full bulletin
and/or Insufficient Cooling due to the seals going bad within the part.
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative...
Read full bulletin
and/or Insufficient Cooling due to the seals going bad within the part.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
Steering
7 bulletinsThis service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or...
Read full bulletin
fluid leak concern that is caused during extremely low temperatures.
This informational bulletin provides information on Steering Bump or Clunk Noise on Rough Roads or Potholes.
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or...
Read full bulletin
fluid leak concern that is caused during extremely low temperatures.
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that...
Read full bulletin
experience a steering hose leak.
This Preliminary Information communication provides information to the technician about vehicles that show a "Take...
Read full bulletin
Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise...
Read full bulletin
or fluid leak concern that is caused during extremely low temperatures.
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.
Suspension
6 bulletinsThis service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise...
Read full bulletin
from Rear Leaf Springs.
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise...
Read full bulletin
from Rear Leaf Springs.
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise...
Read full bulletin
from Rear Leaf Springs.
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak...
Read full bulletin
noise from the metals making contact.
This technical bulletin provides a procedure for retorque the lead springs.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR...
Read full bulletin
VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.
Software & Calibration
6 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This informational bulletin explains to the technician how to validate software calibrations have been tampered with by...
Read full bulletin
means of using aftermarket mods.
This Preliminary information communicates to the dealer technicians to refer to campaign 17337 for calibration updates...
Read full bulletin
for P20EE.
Hybrid & EV
2 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.