2001 GMC Sierra 2500 TSBs

*JG

*YH

*TT

*TT

*TT

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

location.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

engine is started while diagnosing for noise from the engine or transmission.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.

service engine replacement.

Due to Aftermarket Power-Up Devices vs Non Overpower Engine Non-Function of Pistons, Cylinders, Valvetrain Components, DTC P003A or P111D Set

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

GASKET SEALING SURFACES.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE

4.3, 4.8, 5.3, 5.7 AND 6.0 ENGINES COUPLED WITH THE 4L60E OR 4L65E MAY EXPERIENCE A CONDITION OF HESITATES, MISSES OR LOSS OF POWER UNDER ACCELERATION. THE VEHICLE MAY OPERATE AS IF IT IS IN REDUCED POWER MODE. *PE

P0757, P0894, HARSH OR DELAYED SHIFTS, SLIPS, NO DRIVE, NO REVERSE. *PE UPDATED 6/11/10. *PE

MODELS P32/P42 1994-1999 INCLUDED. *TT

It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."

it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

AUXILIARY BATTERY FEED MAY CAUSE FUSIBLE LINK TO MELT AND OPEN CIRCUIT TO PREVENT DAMAGE OR FIRE IN WIRING HARNESS, DUE TO ELECTRICAL OVER LOAD. *PE

*TT

*TT

Allegation Resolution (PAR) claim.

Allegation Resolution (PAR) claim.

Only).

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

*TT

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

Only).

Only).

Spin-On Oil Filters.

Only).

and Canada.

Spin-On Oil Filters.

Spin-On Oil Filters.

Spin-On Oil Filters.

Spin-On Oil Filters.

*SLC

PARK / NEUTRAL POSITION SWITCH, USUALLY WHEN TRYING TO REMOVE THE SWITCH DURING TRANSMISSION SERVICE. *TT

*TT

TRANSMISSION MAY EXHIBIT A VIBRATION (LAUNCH SHUDDER) DURING ACCELERATION FROM 0-40 KM/H (0-25).

The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.

P0701, P1709, P1711, P1713, P0841, P0843, P0847, P0870, P0872, AND P0875. *KB

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

additive.

The customer communication requested return of unsold inventory to inspect for damage to the braided hose and crimps. Damaged braided hoses and poor crimps can lead to immediate leaking. This issue manifests immediately if present, so would drive replacement and therefore impact the end user in time to complete installation.

using the evaporative emission cart smoke machine and ultrasonic leak detectortools.

*TT

repairs requiring balance and Road Force measurement.

repairs requiring balance and Road Force measurement.

used to install wheels onto vehicles

used to install wheels onto vehicles

Turns.

to be replaced if the brake pedal moves or applies on its own at a full turn.

to be replaced if the brake pedal moves or applies on its own at a full turn.

Replacement Guidelines.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

The customer communication requested return of unsold inventory to inspect for incorrect UPC. Incorrect UPC could lead to a discrepency of inventory at the store. Incorrect UPC would have no impact to the end user as it is a box labeling issue and doesn't impact the part itself.

Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.

Fog/Driving Lamp Damage.

Accessories.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

noise from the metals making contact.

The customer communication requested return of unsold inventory to inspect for the spline size. If the spline size is incorrect it will not have a tight fit with the mating component, and would lead to detectable play and/or noise when steering.

*SC