2026 Genesis GV80 TSBs

Technical Service Bulletin (TSB) 26-01-003G-1 provides instructions to remove the old garnish and install new parts.

This bulletin provides instructions to remove the old garnish and install new parts.

Technical Service Bulletin (TSB) 26-01-003G provides instructions to remove the old garnish and install new parts.

This bulletin provides instructions to remove the old garnish and install new parts.

This bulletin provides instructions to remove the old garnish and install new parts.

instrument cluster due to Recall 031G being performed with the incorrect software version.

instrument cluster due to Recall 031G being performed with the incorrect software version. This bulletin provides instructions to update the AVN system with the latest software to correct this condition.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

This may be due to an occasional disconnection on Verizon's communication network. Technical Service Bulletin (TSB) 26-01-035G provides instructions to verify Connected Car Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Connected Car Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

repeatedly waking up vehicle control modules. This condition may result in increased 12-volt battery drain and potential battery discharge. This bulletin provides instructions to update the Ultra-Wide Band (UWB) and Body Domain Controller (BDC) software to improve module wake-up logic and reduce unnecessary control module activation associated with the Digital Key 2 Premium passive entry feature.

This bulletin describes the procedure to inspect the vehicle for the hum or whine noise and, if necessary, to tighten the rear differential lock nut to specification. If the hum or whine noise remains after tightening the lock nut, then this bulletin provides instructions to replace the rear differential or other driveline components as necessary.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.