2024 Genesis GV70 Electrified TSBs

coming from the battery system assembly (BSA) lower cover. This may be caused by the lower cover becoming loose around the center mounting bolts. Follow the procedure in this bulletin to replace the mounting bolts and install cup washers with each bolt to hold the cover in place and resolve the noise on affected vehicles.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in Technical Service Bulletin (TSB) 26-EV-004G to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement. Please note that any vehicles under 15 years/180,000 miles are covered by this TSB, even if vehicle is within High Voltage Warranty of 10 years/120,000 miles.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in this bulletin to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement.

This bulletin provides instructions to perform two software updates for the Power Tailgate (PTG) module to resolve this condition.

may exhibit a condition while driving where the 12V battery voltage drops below the operational voltage and the Vehicle Control Unit (VCU) places the vehicle in Limp Home mode. The VCU software in this bulletin updates the maximum vehicle speeds for various levels of 12V battery voltage when the vehicle enters Limp Home mode.

require an Integrated Charge Control Unit (ICCU) replacement, such as required for DTC P1A9096 DC to DC related charging concern or for inoperative AC charging. The ICCU fuse accessible from a rear side panel of the EV Battery, should NEVER be replaced by itself prior to receiving an ICCU replacement part. The ICCU fuse should be replaced at the same time as replacing the ICCU part. o The ICCU fuse function is to protect the EV Battery from a damaged ICCU. o DTC P1B77 Power Relay Assy (PRA) damage in the EV Battery can occur when an ICCU fuse is first replaced without also replacing the ICCU together. o Vehicles with P1B77 require Techline approval for field staff involved EV Battery repair and can result in significant additional delay for customers. o Wait to receive ICCU replacement part first before also replacing the ICCU fuse on the rear side of the EV battery. This bulletin also covers how to handle a situation when the nut(s) at the rear of the ICCU fuse falls back into the battery.

service part from the head lamp assembly for certain G70 (IK), GV70 (JK1), GV70 Electrified (JK1a EV), and GV80 (JX1) vehicles. For G70 (IK) vehicles, the ILCU is called LED Drive Module (LDM). In cases where the head lamp assembly needs replacement due to exterior damage such as a cracked lens, broken housing, etc., it is recommended to replace the head lamp sub-assembly only (not the entire head lamp assembly) and reuse the existing ILCU or LDM if no problem is found with it.

This battery diagnosis function displays the various battery-related faults such as: Internal short circuit Battery deterioration Malfunction of electronic parts Insufficient battery charge Normal battery Charging defect Battery diagnosis uses the battery sensor history saved for the last 30 days and ICU diagnostic communication to track battery state of charge (SOC) and current parasitic draw history.

have a condition where low 12V auxiliary battery charging occurs due to an ICCU (Integrated Charge Control Unit) fault and may set the following DTC P1A9096 DC/DC Converter Input Voltage Sensor Fault. When a fault occurs, the vehicle may enter a reduced power mode while various warning lights, an audible chime will sound, and large messaging in the vehicles instrument cluster will appear and instruct the driver to stop the vehicle. The Service Procedure flow to be followed is outlined by the flowchart on Page-3. The ICCU system is to be checked by GDS for DTC P1A9096 and depending on the result, will involve either an ICCU software update, or ICCU and fuse replacement.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

navigation, voice recognition, and Bluetooth functionality. In some cases, the home screen may display applications not intended for the U.S. market. This TSB provides the procedure to update the Premium Gen6 Navigation software to address these conditions.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater and updated by USB. The NAU website is https://update.genesis.com/US/EN/navigationUpdate. For certain models equipped with a relevant Genesis Connected Services (GCS) package, the software may be downloaded and applied via OTA update.

This may be due to the shield width of the coaxial cable being too wide, causing a loose connection. Follow the procedures in this bulletin to adjust the width of the shield using a supplied shield adjustment jig.

have a condition of the power down warning light (turtle symbol) with "Power is limited" displayed in the cluster, and possible DTC P0A2F. If you are servicing a vehicle with either of these conditions, follow this bulletin to inspect the EOP.

Follow the procedure in this bulletin to inspect and, if necessary, replace the floor console assembly.

charging with a 240V AC (Level 2) charger where the vehicle experiences an interrupted charging session or a lower charging speed. This occurs to prevent potential damage to the charging cable connection. Follow the procedure in this TSB to update the software logic for the Vehicle Charging Management System (VCMS), which initiates a self-restart that allows the vehicle charging to return to full capacity once stabilized.

may experience an incomplete OTA update. Follow the procedures in this bulletin to check whether the OTA update completed and, if not, update the AVN 6th Gen system using the applicable supplied USB drive(s).

in this TSB to replace any missing/damaged insulation cap(s) on certain 2023-24MY GV60 (JW1 EV), G80 Electrified (RG3 EV) and GV70 Electrified (JK1a EV) vehicles. The charging insulation caps are important to ensure proper charger connector orientation and fit to the vehicle charge port.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

Follow the procedure in this TSB to inspect the source of the noise and, if necessary, replace the Steering Shaft Dust Cover.

Follow the information in this bulletin for replacing the phone call button on the steering wheel.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

Electrified (JK1A EV) vehicles to reduce excessive wind noise conditions. This bulletin only applies if the excessive wind noise condition has been isolated to the panoramic sunroof.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.

This bulletin provides a guide to inspect and replace the horns.

This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.

o Revised logic to enable brake light actuation during regenerative braking at certain deceleration speeds and during i-Pedal mode driving without the need to press the brake pedal i-Pedal mode operation logic update. Revised i-Pedal operation logic. 12V battery saver logic update allows charging from EV Battery as low as 10% battery SOC (State of Charge) when vehicle is parked.