2024 Genesis GV60 TSBs

coming from the battery system assembly (BSA) lower cover. This may be caused by the lower cover becoming loose around the center mounting bolts. Follow the procedure in this bulletin to replace the mounting bolts and install cup washers with each bolt to hold the cover in place and resolve the noise on affected vehicles.

Genesis G80 Electrified vehicles may require replacement of the Integrated Charging Control Unit (ICCU) and ICCU Fuse. At Genesis, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, Genesis is extending the warranty coverage for the ICCU and ICCU Fuse Replacement under this condition to 15 years or 180,000 miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in Technical Service Bulletin (TSB) 26-EV-004G to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement. Please note that any vehicles under 15 years/180,000 miles are covered by this TSB, even if vehicle is within High Voltage Warranty of 10 years/120,000 miles.

years/180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

180,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the flowchart in this bulletin to check for an active or stored occurrence of any Diagnostic Trouble Code (DTC) that requires replacement of the ICCU and replace the ICCU and ICCU fuse if necessary. Some vehicles may have an active DTC that requires ICCU replacement.

may exhibit a condition while driving where the 12V battery voltage drops below the operational voltage and the Vehicle Control Unit (VCU) places the vehicle in Limp Home mode. The VCU software in this bulletin updates the maximum vehicle speeds for various levels of 12V battery voltage when the vehicle enters Limp Home mode.

The Battery Management System (BMS) software logic could cause an HV battery cell voltage to be misread under specific conditions resulting in a false-positive DTC P1AA900, MIL on, and 80% maximum HV battery charge limit. There is no other effect on the vehicle and all systems remain operational. Regardless of whether the vehicle has an active DTC P1AA900 or not, follow the procedure in this TSB to update the software for the Battery Management System (BMS).

have a condition where low 12V auxiliary battery charging occurs due to an ICCU (Integrated Charge Control Unit) fault and may set the following DTC P1A9096 DC/DC Converter Input Voltage Sensor Fault. When a fault occurs, the vehicle may enter a reduced power mode while various warning lights, an audible chime will sound, and large messaging in the vehicles instrument cluster will appear, instructing the driver to stop the vehicle. The vehicle will be inspected for a DTC P1A9096 and may require either an ICCU software update or ICCU replacement and fuse replacement.

auxiliary battery charging occurs due to an ICCU (Integrated Charge Control Unit) fault and may set the following DTC P1A9096 DC/DC Converter Input Voltage Sensor Fault. When a fault occurs, the vehicle may enter a reduced power mode while various warning lights, an audible chime will sound, and large messaging in the vehicles instrument cluster will appear and instruct the driver to stop the vehicle. The Service Procedure flow to be followed is outlined by the flowchart on Page-3. The ICCU system is to be checked by GDS for DTC P1A9096 and depending on the result, will involve either an ICCU software update, or ICCU and fuse replacement.

auxiliary battery charging occurs due to an ICCU (Integrated Charge Control Unit) fault and may set the following DTC P1A9096 DC/DC Converter Input Voltage Sensor Fault. When a fault occurs, the vehicle may enter a reduced power mode while various warning lights, an audible chime will sound, and large messaging in the vehicles instrument cluster will appear, instructing the driver to stop the vehicle. The vehicle will be inspected for a DTC P1A9096 and may require either an ICCU software update or ICCU replacement and fuse replacement.

This may be due to an occasional disconnection on Verizon's communication network. Technical Service Bulletin (TSB) 26-01-035G provides instructions to verify Connected Car Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Connected Car Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Connected Car Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to reset the Connected Car Data Communication Unit (DCU) in Dealer Mode to resolve the connection.

securing pads on the back of the rear seat. This bulletin provides instructions to replace the cargo mat with a new part.

o Revised logic to enable brake light actuation during regenerative braking at certain deceleration speeds and during i-Pedal mode driving without the need to press the brake pedal i-Pedal mode operation logic update. Revised i-Pedal operation logic. 12V battery saver logic update allows charging from EV Battery as low as 10% battery SOC (State of Charge) when vehicle is parked.

o Revised logic to enable brake light actuation during regenerative braking at certain deceleration speeds and during i-Pedal mode driving without the need to press the brake pedal i-Pedal mode operation logic update. Revised i-Pedal operation logic. 12V battery saver logic update allows

i-Pedal mode operation logic update. 12V battery saver logic update allows charging from EV Battery as low as 10% SOC when parked.

to an internal logic error that prevents the updates from being completed properly. This bulletin provides instructions to perform a Data Connectivity Unit (DCU) software update to correct this condition.

to an internal logic error that prevents the updates from being completed properly.

pin caps) which may lead to damage to the charge port if not replaced. This bulletin provides instructions to replace the DC pin cap(s).

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater and updated by USB. The NAU website is https://update.genesis.com/US/EN/navigationUpdate. For certain models equipped with a relevant Genesis Connected Services (GCS) package, the software may be downloaded and applied via OTA update.

This bulletin provides instructions to install washers to the side guide bumpers on the tailgate side panel or body panel.

vehicles that experience a rattle noise from the tailgate area while driving.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

to an internal logic error that prevents the updates from being completed properly.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This bulletin provides a guide to inspect and replace the horns.

This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.

This bulletin provides the procedure to update the software of the SWRC system on these vehicles to improve the switch operation.