2018 Genesis G90 TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

replace the related solenoid and E-module or park position switch.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Genesis G80 (DH) and Genesis G90 (HI) vehicles equipped with Lambda 3.3T / 3.8L GDI engines.

Genesis G80 (DH) and Genesis G90 (HI) vehicles equipped with Lambda 3.3T / 3.8L GDI engines.

certain 2018MY G80 (DH) and G90 (HI) vehicles equipped with Lambda engines.

cap may have the incorrect text for engine oil viscosity printed on top.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

capacity information indicated on tire placards when the vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of the Gross Vehicle Weight Rating or 45.4kg (100 pounds). If the total added weight exceeds the lesser of the limit, a label (See Figure 1) must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

replace the related solenoid and E-module or park position switch.

some vehicles which may exhibit a coolant leak between the ATF connector and engine side heater pipe.

replace the E-module.

which may exhibit a coolant leak between the ATF connector and engine side heater pipe.

replace the E-module.

Perform this update if a vehicle is in for service for an intermittent no start concern.

replace the related solenoid and E-module or park position switch.

replace the E-module.

replace the related solenoid and E-module or park position switch.

Drain, (2) Genesis Connected Services (GCS) Activation Issues, (3) Genesis Connected Services Remote Service Failures, (4) Genesis Connected Services Point of Interest Failures. Follow the instructions in this TSB to update the AVN.

Drain, (2) Genesis Connected Services (GCS) Activation Issues, (3) Genesis Connected Services Remote Service Failures, (4) Genesis Connected Services Point of Interest Failures. Follow the instructions in this TSB to update the AVN.

This bulletin provides information on replacing the electric thermostat. No drivability issues are associated with this condition.

This bulletin provides information on replacing the electric thermostat. No drivability issues are associated with this condition.

This bulletin provides information on replacing the electric thermostat. No drivability issues are associated with this condition.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

with Blue Link SOC reporting ability.

This bulletin provides a guide to inspect and replace the horns.

This bulletin describes the procedure to install an e-ring clip to the tilt pipe housing on the front seat.

recommended safe chemical products.

This bulletin describes the procedure to install an e-ring clip to the tilt pipe housing on the front seat.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

How to program smart key FOB and card key. How to program additional key FOB when applicable.

(transmission clutch slip in gear above limit) listed on Page 2.

OEM (new) and remanufactured automatic transmissions:

OEM (new) and remanufactured automatic transmissions:

from Reverse to Drive or Drive to Reverse. Replace the electronic shifter with a new shifter that has a production date of 6/2/17 or newer to resolve this condition.

slipping more than 200 rpm in gear).

This procedure is necessary to reduce the TCM learning time and improve the shift quality.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

diagnosing and conducting alignment-related repairs for all models and model years.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

vehicles are equipped with the Service Interval Reminder Feature. Follow the information outlined in this bulletin to enable and set the Service Interval Reminder Feature on the applicable models listed below.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

Genesis G90 with LED Headlights.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

and operating difficulties with the home garage system. This bulletin provides information related to some of the possible symptoms.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

exhibiting a noise from the rear brakes.

This bulletin provides information of how to diagnose the no charging condition.

This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.