2025 Genesis G70 TSBs

systems not loading after an Over the Air (OTA) software update due to an error in the software update logic.

systems not loading after an Over the Air (OTA) software update due to an error in the software update logic. This bulletin provides instructions to use a provided USB stick to perform a manual software update to correct this condition.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater and updated by USB. The NAU website is https://update.genesis.com/US/EN/navigationUpdate. For certain models equipped with a relevant Genesis Connected Services (GCS) package, the software may be downloaded and applied via OTA update.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

The inspection and repair procedure involves confirming if the garnishes have separated and if necessary, removing the garnish and replacing with new parts.

The inspection and repair procedure involves confirming if the garnishes have separated and if necessary, removing the garnish and replacing with new parts.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.

This may be due to an irregular disconnection on Verizon's communication network.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.

display warning messages on the instrument cluster, resulting in the PDW sensor(s) failing to detect nearby objects or triggering multiple false alarms. This condition may be a result of external damage to the PDW sensor membrane or sensor cover from rock chips or road debris, a collision, or previous vehicle repairs or modifications.

This may occur when the parts housing the sensor become loose, causing the sensor to falsely detect objects. There is no functional effect on the vehicle other than the false notification. This bulletin provides the procedure to inspect the vehicle and apply repair(s) as needed.

This condition may affect braking smoothness or generate minor noise. This bulletin provides instructions to perform brake disc burnishing or machining on the affected front and/or rear brakes as necessary, to restore proper braking performance.

This condition may affect braking smoothness or generate minor noise.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.

Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This bulletin provides instructions to inspect the A/C system for leaks and replace the evaporator core, if necessary.

This bulletin contains instructions on replacing the Rear Corner Radar units (LH/RH), performing radar calibration, and variant coding.

This bulletin provides a guide to inspect and replace the horns.

This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.