2020 Freightliner Coronado TSBs

The following guidelines are for cleaning and disinfecting commonly touched surfaces on the inside and outside of a vehicle. For best results, follow cleaning and disinfecting procedures fully and consistently. Ensure there is adequate ventilation when using chemicals. NOTICE: Wipe down fragile components carefully to avoid damaging the vehicle.

managers.

This version replaces the version dated 5/1/14 and adds New Cascadia.

DTNA Workshop Manuals, which states that there are very few cases in which welding a heat-treated frame rail is allowed. Therefore, before welding anything on a frame rail, contact the applicable regional service representative for approval.

managers

The One Stop Supplier Extended Program streamlines the claim filing process because with One Stop Supplier Extended, the service network will file claims for some supplier-supported coverages in OWL. Revisions are in blue.

The One Stop Supplier Extended Program streamlines the claim filing process because with One Stop Supplier Extended, the service network will file claims for some supplier-supported extended coverages in OWL.

Identifies and addresses discrepancies from the sales order.

Warranty (Parts Warranty).

This bulletin replaces the version dated 11/11/2019. Figure 3 has been updated with a new hardware part number. A procedure was added to the data download process.

This bulletin replaces the version dated 5/31/2017. Information is added about the BCT-460DTNA PowerNet Assessment Tool. When troubleshooting Powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter is the only Daimler-approved tool for troubleshooting vehicle Powernet issues.

Use the guidelines in this bulletin to determine if a damaged electrical harness should be repaired or replaced.

Older modules will not be compatible with newer module.

Occasionally we see trucks come in with fuel leaking from the high pressure fuel pump weep hole. This is NOT a defect in the pump and further diagnostics need to be performed to find the root cause.

Some engine component failures can cause metallic debris to circulate throughout the engine lubrication system. Although the oil filter will capture most of this debris, some debris may enter the clean side of the lubrication system during oil filter bypass. Detroit has created a lubrication system cleaning and flushing procedure to address this problem.

Parts Information.

Revision removed steps instructing removal and installation of wheels. Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed.

Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed.

With the start of production on March 2, 2020, the fasteners used to assemble the non-Airliner rear suspension (bogie) crossmember have changed. The rear suspension bogie crossmember gussets to the C-channel will be assembled with 5/8 - 18 fasteners. This change includes a revision to a higher friction nut that requires an increase in tightening torque. The new higher friction nut can be identified by its green color.

This service bulletin replaces the version dated 05/01/2016. This bulletin is updated to include the parts list. Some vehicles may exhibit a lean (right or left) due to weight difference on the front suspension. While this does not affect the operation of the vehicle, it may be visually unpleasing to many customers. To correct this condition, replace the existing front axle spacer on the low side of the vehicle with a thicker one.

available for download from the Detroit Diesel server.

available for download from the Detroit Diesel server.

To maintain access to the Detroit server, all DiagnosticLink computers must be updated with the current version of DiagnosticLink software. all DiagnosticLink 8.08 installed versions will be disabled as of Tuesday, January 28, 2020.

60-day expiration, starting on the release day of the bulletin. The intent of a SIB is to notify the service network of a major change to one or more service procedures. Do not save SIBs nor reference them for repairs, as they are uncontrolled and never updated.

distance for paint finish standards.

Though the backup light harness is long enough to connect to the backup light switch, it may be short enough that the wire seals in the connector can be stressed. Moisture entering through the seals can cause corrosion, resulting in a bad connection and/or failure of the switch. As a result, backup lights and, if equipped, the backup alarm, may not function when the vehicle is shifted into reverse.

Freightliner 108SD/114SD, Coronado, New Cascadia, and Business Class M2 vehicles and Western Star 4700 and 4900 vehicles equipped with a certain tire rating have the wrong Component GWR label. DTNA is requesting the current Component GWR label be replaced with the correct label.