2015 Ford Transit Connect TSBs

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

programmed for the European market instead of the North American market

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

the taxi spot lights to the main body harness. Service Part Number GU2Z-14S411-JA.

WHEN INSTALLING THE NEW ROOF SHADE THE WIRE HARNESS CONNECTOR FOR THE ROOF SHADE MODULE MAY NEED TO BE EXTENDED IN ORDER TO REACH THE NEW MODULE. FOLLOW THE RECOMMENDED SPLICING METHOD FOR EXTENDING THE HARNESS IN THE ON-LINE WIRING DIAGRAMS SECTION 5-1, CONNECTOR REPAIR PROCEDURES.

THE CORNERING LAMPS SHARE THE SAME BULB AS THE FOG LAMPS AND ILLUMINATE WHEN THE VEHICLE SPEED IS LESS THAN 25 MPH AND THE BODY CONTROL MODULE (BCM) RECEIVES A REQUEST FOR A TURN SIGNAL OR THE STEERING WHEEL IS TURNED GREATER THAN 35 DEGREES FROM CENTER. BEFORE DIAGNOSING A RIGHT OR LEFT FOG LAMP THAT MAY SEEM TO BE STUCK ON, TURN THE STEERING WHEEL BACK TO CENTER. IF THE LAMP GOES OFF, THE VEHICLE IS EQUIPPED WITH CORNERING LAMPS AND ARE WORKING AS DESIGNED. REFER TO THE WORKSHOP MANUAL SECTION 417-01 EXTERIOR LIGHTING.

control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market, resulting in the following symptoms: The radio band cannot be changed from FM1 (the tuner may change to AM but the display continues to show FM1). Satellite radio cannot be accessed. The Europe-specific park distance control feature is enabled, and displays on the FCDIM when the forward vehicle speed drops below 6 mph (10 kph).

vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market, resulting in the following symptoms: h The radio band cannot be changed from FM1 (the tuner may change to AM but the display continues to show FM1). h Satellite radio cannot be accessed. h The Europe-specific park distance control feature is enabled, and displays on the FCDIM when the forward vehicle speed drops below 6 mph (10 kph). Additionally, on some of the affected vehicles that are equipped with the rear camera zoom feature, the body control module (BCM) may be misconfigured, causing the rear camera zoom feature to be inoperative

MODEL 2014-15 TRANSIT CONNECT. *PE

FROM BODY CONTROL MODULE (BCM) FOR TURN SIGNAL WILL STAY ON WHEN STEERING WHEEL IS CENTERED. MODEL 2014-15 TRANSIT CONNECT. *PE

THESE VEHICLES HAVE THE LATEST LEVEL SYNC SOFTWARE. *LJ

Converter Replacement, If Required After Dealer Evaluation

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

(GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.

IF NORMAL BATTERY DRAIN DIAGNOSIS LEADS TO NO ISSUES, IT MAY BE CAUSED BY THE APPROACH LIGHTS ILLUMINATING EVERY TIME THE BODY CONTROL MODULE (BCM) RECEIVES A LOCK/UNLOCK SIGNAL OR OPENING ANY DOOR. IF THE DOOR REMAINS OPEN, THE LIGHTS WILL REMAIN ILLUMINATED FOR UP TO 10 MINUTES. IF THE VEHICLE WAS BUILT ON OR BEFORE 11-DEC-2016, REPROGRAM THE BCM TO THE LATEST CALIBRATION USING IDS RELEASE 103.05 AND HIGHER. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFT.COM. FOR ALL VEHICLES, ACCESS THE BCM CONFIGURATION PARAMETERS. SELECT MODULE PROGRAMMING, PROGRAMMABLE PARAMETERS, PERSONALITY, APPROACH LIGHT. CHOOSE DISABLED AND FOLLOW THE SCREEN PROMPTS TO COMPLETION. USE CAUSAL PART 14A068 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

MIL WITH VARIOUS DRIVABILITY ISSUES AND ONE OR MORE OF THE FOLLOWING DTCS: P0010, P0103, P0104, P0122, P0131, P0135, P0137, P0141, P0201-P0204, P0217, P0222, P0223, P025A, P0300, P0301-P0304, P0316, P0351-P0354, P0400, P0403, P0443, P1285, P1289, P128A, P1299, P2101, P2107, P2111, P2112, P2122, P2127 AND/OR U0109. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

P0074 AND/OR U0422 ISSUE Some 2014-2016 Transit Connect vehicles equipped with 2.5L engine may exhibit an intermittent condition in which the ambient air temperature (AAT) display in the instrument panel cluster (IPC) is inaccurate and/or the A/C is inoperative. The inoperative A/C may be caused by the AAT reading below -1.1 C (30 F) the actual ambient temperature is above -1.1 C (30 F) with diagnostic trouble codes (DTCs) P0073, P0074 and/or U0422.

Not Covered in Safety Recall: 20S15 or 23S36 Door Latch Replacement and Inspection

portions of the windshield may have inadequately adhered to the vehicle. Affected vehicles could experience increased wind noise, water leaks, or looseness of the windshield glass

Follow the Service Procedure steps to correct the condition.

Some 2014-2016 Transit Connect vehicles may exhibit a condition in which the panoramic roof panel blind moves and stops 150 mm (6 inches) from the full open position or does not move at all. The blind may be buckled and/or stuck. 1. Is the panoramic roof panel blind inoperative, buckled and/or stuck? a. Yes - proceed to Step 2. b. No - this article does not apply. Refer to Workshop Manual (WSM), Section 501-05 for normal diagnosis. 2. Replace the panoramic roof panel blind assembly. Refer to WSM, Section 501-05.

EXHIBIT SMALL SCRATCHES ON THE SLIDING DOOR BODY PANEL OR EITHER DOOR. *LJ

PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

*LJ

Replacement If Required After Dealer Evaluation

second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.

SEE DOCUMENT SEARCH BUTTON LETTER. BULLETIN INFORMATION INVOLVING 2014-2015 TRANSIT CONNECT WAGONS THIRD ROW SEAT REMOVAL. *LJ

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.

P0073, P0074, and/or U0422

This may be due to an excessive gap in the heating, ventilation, and air conditioning (HVAC) case allowing water to drip from the case when the air conditioning (A/C) is operating. To correct the condition, follow the Service Procedure steps to reseal the HVAC case.

This may be due to an excessive gap in the heating, ventilation, and air conditioning (HVAC) case allowing water to drip from the case when the air conditioning (A/C) is operating. To correct the condition, follow the Service Procedure steps to reseal the HVAC case.

*LJ

25N15 - PAUSED effective July 15, 2026 AWARENESS COMMUNICATION Monitor FSA Landing Page in PTS for further details - Certain 2015-2019 Model Year Multiple Vehicle Lines - Rear View Camera Inspection For One-Time Replacement

Inspection For One-Time Replacement

second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable in need of adjustment. Follow the Service Procedure steps to correct the condition.

FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

THIS CONCERN IS UNDER INVESTIGATION. DO NOT REPLACE THE HEADLAMP ASSEMBLY. TO SERVICE, USE PIGTAIL KIT 8U2Z-14S411-GA. DO NOT SHORTEN THE WIRES ON THE PIGTAIL KIT, SO THEY CAN ACT AS A HEAT SINK TO DRAW HEAT AWAY FROM THE BULB. A NEW PART AND PROCEDURE IS BEING DEVELOPED. MONITOR OASIS FOR UPDATES.

Some 2013-2022 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.

Some 2013-2018 Transit Connect vehicles built on 1-Jan-2013 and through 5-Jan-2018 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat. Follow the Service Procedure steps to correct the condition.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB  SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB  SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.