2021 Ford Mustang TSBs

Reason For Update: Change the part number for the transmission fluid heat exchanger bolt (Expedition/Navigator) as well as change the claim/package quantities for HL3Z-7B442-F and HL3Z-7B164-C. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to PCM software and/or axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to PCM software and/or axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order to document any additional repairs

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to PCM software and/or axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order to document any additional rep

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to PCM software and/or axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order to document any additional re

Updated Part List with 3 superseded part numbers. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to PCM software and/or axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect, replace other transmission components and flush transmission fluid cooler only as necessary

Reason for update: update the Part List and Service Procedure Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order to document any additional

noise at idle and/or while driving.

equipped with a 10R80 transmission (excluding hybrid) may exhibit harsh/delayed engagements and/or harsh/delayed shifts, an illuminated MIL with DTC P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the PCM or TCM. This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. To correct the condition, follow the Service Procedure to verify hydraulic circuit leakage and replace the CDF clutch cylinder (7H351) if necessary.

that may be perceived as an engine misfire during throttle tip-in between 35-45 mph (56-72 km/h) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation is a characteristic of the vehicle and can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition. If no DTC is set, inform the customer that the vehicle is operating as designed. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B.

with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12 for installation.

with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12D for installation.

This may be due to the Integrated Diagnostic System (IDS) software level. To correct this condition, make sure the IDS software is at R130.04 or newer when configuring the BCM. If the state of charge (SOC) is less than 50%, charge the battery by attaching the battery charger's negative clamp to the engine or chassis ground and not the negative battery terminal. Refer to Workshop Manual (WSM), Section 414-01.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System  General Information > Diagnosis and Testing > Engine > PPT F > Step F2.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.

Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2023 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the keep alive memory in the PCM/TCM or the transmission main control valve body. To correct the condition, follow the Service Procedure to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.

removal and replacement of the inner tie rods and bellows boots is required. To assist engineering with root cause analysis of failed steering gears, include these parts in the same package when returning warranty replacement steering gears. Make sure to avoid damage to the bellows boots or inner tie rods during removal. The steering gear should also be packaged in the original box with all protective insulators in place to properly protect it during shipping.

(DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, and/or P0308 stored in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

that may be perceived as an engine misfire during throttle tip-in between 35-45 mph (56-72 km/h) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation is a characteristic of the vehicle and can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition and no repair attempts should be made. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B.

that may be perceived as an engine misfire during throttle tip-in between 35-45 MPH (56-72 KPH) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) and driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B.

panel cluster (IPC) with diagnostic trouble codes (DTCs) C1034, C2005, C2006, C2007 and/or C2008 stored in the anti-lock brake system (ABS) module and/or a parking brake that sticks after being applied. This may be due to internal binding of the piston within the parking brake caliper. To correct the condition, follow the Service Procedure to replace the parking brake caliper(s).

automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to enter only the 13-digit solenoid body strategy when downloading transmission strategy.

illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0300 and/or P0316 in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

when accelerating from a stop, with a powertrain malfunction (wrench) indicator and DTCs P1601/P061A while using SelectShift. This may be due to powertrain control module (PCM) calibration. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle but not to use SelectShift. Engineering is currently working on a solution for this condition that is expected in June 2022. Replacement or reprogramming of the PCM will not resolve this condition at this time. Schedule a follow-up appointment for repair in June 2022. Once the update becomes available, contact the customer and confirm the service appointment. Monitor OASIS for updates.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12D for installation.

when accelerating from a stop, with a powertrain malfunction (wrench) indicator and DTCs P1601/P061A while using SelectShift. This may be due to powertrain control module (PCM) calibration. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle but not to use SelectShift. Engineering is currently working on a solution for this condition that is expected in April 2022. Replacement or reprogramming of the PCM will not resolve this condition at this time. Schedule a follow-up appointment for repair in April 2022. Once the update becomes available, contact the customer and confirm the service appointment. Monitor OASIS for updates.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to obtain a new main control valve body with a new strategy number.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.

24-Sep-2021 may exhibit an illuminated MIL and diagnostic trouble codes (DTC) P0300 and/or P0316 in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.

phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.

rough running drivability concern with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0351, P0352, P0353 and/or P0354 stored in the powertrain control module (PCM). This may be due to a software parameter within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.

In addition to following normal Workshop Manual (WSM) diagnostics, inspect C105, an inline connector next to the right side valve cover, for signs of pushed out terminals, terminal damage, or harness damage. If any pushed out terminals, terminal damage, or harness damage is found, repair as necessary.

App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.

In all of the affected vehicles, a High Voltage Battery Module (HVBM) was previously replaced using an incorrect Thermal Interface Material (TIM) template. A HVBM that has been serviced using the incorrect TIM template may cause the cells to operate at a temperature higher than design intent, resulting in reduced cell performance and, over time, a progressive reduction in vehicle range that may become noticeable to the driver. This may also result in a malfunction indicator light, DTC code and battery power limiting.

toggle button in the Connectivity setting menu grayed out with an inability to switch it off.

the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.

concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software

using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.

using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.

Quality Improvements include- The customer is instructed to exit the vehicle when a battery hazard is detected

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

Some 2021-2022 Mustang Mach-E (non-GT) vehicles equipped with all-wheel drive (AWD) may exhibit a whine noise from the front drive unit when driving steady at speeds between 30-40 mph (48-64 km/h) without diagnostic trouble codes (DTCs) present. This may be due to software parameters. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM).

"track day" cars some of which may be used on both track and highway. SB 23-01 adresses proper installation torque of cap bolt fasteners attaching SPL's aftermarket lower control arms, recurring inspection and confirmation of torque setting and removal and replacement of damaged or under torqued fasteners to reduce risk of premature failure and accident. SB-23-01 was mailed, emailed and posted on SPL website to known resellers, race teams and users of the affected parts and is being submitted here as required by part 579.5. Vehicle Applications include: BMW series 1,2,3,& 4, 2008-2023; Chevrolet Camaro 26-2023, Cadillac ATS, CTS 2016-2019; Ford Mustang 2015-2023; Toyota Supra 2020-2023.

Suspension Fault message displayed in the IPC with diagnostic trouble code (DTC) B14C1:64 with no vehicle symptoms. This may be due to software within the vehicle dynamics module (VDM). To correct the condition, reprogram the VDM using the latest software level of the appropriate Ford diagnostic scan tool.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.

BlueCruise Prep Kit) BlueCruise Module Programming REASON FOR THIS SUPPLEMENT Program Terms: This program has been extended until December 31, 2023. Service Action: Clarifications regarding Technical Information and Blue Zone. Owner Notification Mailing Schedule: updated mail date for revised owner letter. Owner Refunds: adding refunds for software installation done after program expiration. Technical Information: Added steps and clarifications.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

to ensure that customers are getting the best heating performance on their vehicles while driving at highway speeds. These updates will improve the heating capability and the defrost and defog performance when exterior temperatures are at or below -15C/5F

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

control module (PCM) communication condition if the oil level is approximately 1 or more quarts low and the oil life is at or less than 20%. This may be due to various parameters within the PCM. To correct the condition, follow the Service Procedure to reset and reprogram the PCM.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.

Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.

The max fill line may be disregarded, only the min line is relevant. Do not attempt to remove coolant from the high voltage battery coolant expansion tank if the coolant level is above the max fill line.

Assembly Reimbursement

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

engagement Delayed engagement Harsh shift Delayed shift"

rear transmission fluid cooler tubes and transmission case.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

Built On Or Before 15-Aug-2022

(7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.

rear wheel hub when accelerating, applying brakes, or when shifting between drive/reverse (torque reversals). This condition may be caused by stick/slip between the hub and halfshaft interface during the torque reversals creating the ting, pop, clunk, or click noise. To correct the condition, refer to the Workshop Manual (WSM) to replace the halfshaft and hub assembly of the suspected side(s).

noise from the rear wheel hub when accelerating, applying brakes, or when shifting between drive/reverse (torque reversals). This condition may be caused by stick/slip between the hub and halfshaft interface during the torque reversals creating the ting, pop, clunk, or click noise. To correct the condition, refer to the Workshop Manual (WSM) to replace the halfshaft and hub assembly of the suspected side.

of power when accelerating from a stop, with a powertrain malfunction (wrench) indicator and diagnostic trouble codes (DTCs) P1601 and/or P061A stored in the powertrain control module (PCM) while using SelectShift. This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.

an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P175C, P175D, P175E, P0844, P0849 and/or P0874 set in the transmission control module (TCM). This may be due to the software in the TCM. To correct the condition, follow the Service Procedure steps to check the transmission fluid pressure sensor and reprogram the PCM/TCM.

transmission cooler tubes attached to the transmission case. This may be due to the retaining bolts being cross threaded causing the seals to leak and/or crack the lines. If the threads in the transmission case that the cooler tube retaining bolts go into are damaged, it is not necessary to replace the transmission. These threads can be repaired. To correct the condition, follow the Service Procedure to repair these threads and replace the tubes.

cooler tubes attached to the transmission case. If the threads in the transmission case that the cooler tube retaining bolts go into are damaged, it is not necessary to replace the transmission. These threads can be repaired. To correct the condition, follow the Service Procedure to repair these threads.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Some of the vehicles listed in the Model statement above may exhibit a sagging headliner or a gap where the headliner meets the upper door weatherstrip.

Some 2018-2024 Mustang coupe vehicles may exhibit a sagging headliner or gap where the headliner meets the upper door weatherstrip. This may be due to an outward bent door frame moulding not allowing the weatherstrip to overlap the headliner properly. To correct this condition, follow the Service Procedure to replace the door frame moulding.

Letter

This may be due to a detached A-pillar body seal. Follow the service procedure to repair the vehicle.

the differential cooler line fittings. This may be due to a seal within the fittings. To correct the condition, follow the service procedure to replace both rear differential cooler line fittings.

This may be due to an outward bent door frame moulding not allowing the weatherstrip to overlap the headliner properly. To correct this condition, follow the Service Procedure to replace the door frame moulding.

The crack is a cosmetic condition, not a structural concern. This may be due to a variation in production of the hood. To correct the condition, follow the Service Procedure to repair the hood crack.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

Quality Improvements include: - Improved robustness in alignment of turtle light display to reduced power event. - Improved AC Charge process reporting accuracy - Improves HV Battery Charging experience. - Robustness actions for DC Fast Charge: charging and diagnostics. - Improvements to On Demand Preconditioning. - The customer is instructed to exit the vehicle when a battery hazard is detected. - Adds torque to front drive unit to help whine at 30- 70 mph coast condition - Corrects software issue relating to charging which may occur after the BCCM receives an Over The Air (OTA) update. - Corrects ABS cal files

Assistance Not Available message and diagnostic trouble code (DTC) B1578:78 stored in the image processing module A (IPMA) that cannot be cleared. This may be due to the IPMA software. To correct this condition, follow the Service Procedure to reprogram the IPMA to the latest level.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * "Exhaust Mode Selection Not Available" messages * Illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system.

These may include Exhaust Mode Selection Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator.

These may include Drive Mode Not Available or Exhaust Mode Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator .

Some 2018-2022 Mustang vehicles may exhibit various concerns with the active exhaust system. These may include Drive Mode Not Available or Exhaust Mode Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator .

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

level part is available (DS7Z-9904132-A). It is not necessary to replace the sun visor assembly if only the clip is damaged.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

shipped to dealers without a front splitter. The front splitter is a loose shipped item that should be installed during the pre-delivery inspection (PDI) process. For more information, access the following dealership communication located on FMCDealer.com by copying and pasting the following link into a web browser https://www.fmcdealer.dealerconnection.com/content/fmcdealer/en/us/edc/2021/qafmm1p5321.html. The communication can also be found by navigating to the dealer communications page on FMCDealer.com. On the 'Dealer Communication' page, select 'May 2021' in the Month/Year category. Scroll down to 'May 3, 2021' and click on the link 'Q&A: 2021 Ford Mustang Mach 1 Part'.

The blue status indicator light on the charger control box may not illuminate, may turn on and off intermittently, or may illuminate amber. This may be due to the connector which runs between the household outlet and the charger control box not being fully seated into the charger control box. Ensure that this connector is fully inserted into the charger control box. When the connector is properly inserted, the flange on the connector will be flush with the casing of the charger control box. If the flange of the connector protrudes out from the charger control box, the connector is not fully seated into the charger control box.

direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.

This may be due to an incorrectly installed upper spring seat which is part of the front strut assembly. To correct this condition, remove the suspect strut(s) from the vehicle and inspect the upper spring seat for damage and/or incorrect installation and repair as necessary. Refer to Workshop Manual, Section 204-01. For claiming, use casual part 18124 and the applicable labor operations of Section 03 of the Service Labor Time Standards (SLTS) Manual.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

affected vehicles, a front door latch may open to the secondary latched position while driving. While the door is in the secondary latched position the driver will notice wind noise from the door and a door ajar warning will appear on the instrument cluster. This concern does not result in a fully opened door while driving. The occupant can open the door normally using the door handle.