2017 Ford Mustang TSBs

seat belt retractors and return them to Ford for further analysis. Inspecting your vehicle will help Ford carry out this research.

Ford is voluntarily conducting this program to evaluate the field performance and functionality of the obtained front seat belt retractor assemblies. Parts obtained from the program must be returned to Ford for evaluation.

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System  General Information > Diagnosis and Testing > Engine > PPT F > Step F2.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

removal and replacement of the inner tie rods and bellows boots is required. To assist engineering with root cause analysis of failed steering gears, include these parts in the same package when returning warranty replacement steering gears. Make sure to avoid damage to the bellows boots or inner tie rods during removal. The steering gear should also be packaged in the original box with all protective insulators in place to properly protect it during shipping.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.

tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.

This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

This may be due to the valve covers warping due to excessive heat. To correct the condition, follow the Service Procedure steps to add fasteners to both valve covers.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

This may be due to the number of fasteners used to hold the valve cover onto the cylinder head. To correct the condition, follow the Service Procedure steps to add fasteners to both valve covers.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

(DTC) P0300 through P0308 present. A noticeable misfire may or may not accompany these DTCs. If normal diagnostics do not lead to a root cause for this concern, remove the intake manifold from the vehicle and verify the intake manifold runner control (IMRC) plates move when the IMRC actuators are moved by hand. These plates are visible through the outlet ports of the intake manifold. If the IMRC plates do not move when the IMRC actuators are moved by hand, the intake manifold should be replaced. For claiming, use causal part 9424 and applicable labor operations in Section 9 of the Service Labor Time Standards (SLTS) Manual.

If the leak appears to be originating from the oil cooler, be aware that the leak may actually be originating from the oil filter adapter, and oil may run down the oil cooler tubes and drip off of the cooler, making it appear that the leak is originating from the oil cooler. If the true source of the leak is caused by a damaged O-ring where the oil cooler tubes meet the oil filter adapter, be aware that these O-rings are now available as a separate service part from the oil cooler tubes. Replacement O-rings can be ordered using part number FR3Z-00815-A. For claiming, use causal part 6B850 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.

This may be due to the engine oil pressure sensor. Follow the Service Procedure steps to correct the condition.

This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages  SYNC.

each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.

To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.

MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.

OPERATION AT LIGHT LOADS AND SPEEDS FROM IDLE - 3000 RPM. THE NOISE WILL BE MOST NOTICEABLE DURING LIGHT ACCELERATION IN THE 1500-3000 RPM RANGE AND MAY ALSO BE NOTICEABLE IN THE 800-1200 RPM RANGE WITH NEUTRAL THROTTLE BLIPS. THIS SOUND IS CAUSED BY THE PISTON MOTION IN THE CYLINDER BORE. THIS IS AN INHERENT CHARACTERISTIC OF THE FORGED ALUMINUM PISTONS UTILIZED IN THIS HIGH PERFORMANCE ENGINE. ONCE THE ENGINE REACHES OPERATING TEMPERATURE THE NOISE WILL DIMINISH, ALTHOUGH IT MAY STILL BE NOTICEABLE EVEN WHEN FULLY WARM. THERE ARE NO DURABILITY CONCERNS WITH THIS SOUND.

WITH DTCS P0456, P1450 AND/OR P144C. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

INSTRUMENT PANEL CLUSTER MESSAGE CENTER ALONG WITH DTC C103E:00 WHEN DRIVING WITH THE SPACER BLOCKS REMOVED AND LESS THAN 160 KM (100 MILES) ON THE ODOMETER. CHECK THE VEHICLE DYNAMICS MODULE (VDM) FOR THE LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS). MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. RAISE THE VEHICLE ON A HOIST, REFER TO WORKSHOP MANUAL (WSM), SECTION 100-02. SUSPENSION MUST BE UNLOADED WITH THE WHEEL/TIRE ASSEMBLIES HANGING DOWN. PERFORM THE RIDE HEIGHT SENSOR CALIBRATION ROUTINE. FOLLOW THE INSTRUCTIONS IN THE IDS SCAN TOOL.

POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

"track day" cars some of which may be used on both track and highway. SB 23-01 adresses proper installation torque of cap bolt fasteners attaching SPL's aftermarket lower control arms, recurring inspection and confirmation of torque setting and removal and replacement of damaged or under torqued fasteners to reduce risk of premature failure and accident. SB-23-01 was mailed, emailed and posted on SPL website to known resellers, race teams and users of the affected parts and is being submitted here as required by part 579.5. Vehicle Applications include: BMW series 1,2,3,& 4, 2008-2023; Chevrolet Camaro 26-2023, Cadillac ATS, CTS 2016-2019; Ford Mustang 2015-2023; Toyota Supra 2020-2023.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. To resolve the condition, follow the Service Procedure steps to inspect and repair the wiring harness.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. Follow the Service Procedure steps to correct the condition.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

This may be due to the way in which the front controls interface module (FCIM) software regulates the interior temperature. Follow the Service Procedure steps to correct the condition.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

This may be due to the way in which the front controls interface module (FCIM) software regulates the interior temperature. Follow the Service Procedure steps to correct the condition.

(DTC) B1252:13 stored in the accessory protocol interface module (APIM.) This may be due to a loose connection or damage present on the cable which connects the APIM to the media hub. Follow normal Workshop Manual (WSM) diagnosis to correct this condition, while paying close attention to any damage or loose connections which may be present on this cable.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

OR A SYSTEM LOCK UP WHEN THE PHONE IS CONNECTED. APPLINK MAYBE INOPERATIVE, OR THE SYSTEM MAY PERFORM RANDOM REBOOTS DURING AN IGNITION CYCLE WITH THE PHONE CONNECTED. DETERMINE IF THE CUSTOMER HAS AN ANDROID PHONE WITH THE BASEBALL APPLICATION MLB.COM AT BAT INSTALLED. IF THE CUSTOMER DOES NOT HAVE THIS APPLICATION LOADED THEN PROCEED TO THE WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. IF THE CUSTOMER DOES HAVE THIS APPLICATION LOADED VERIFY IF THE VERSION IS 5.1.3 OR LOWER ON THE ANDROID PHONE. IF THE ANDROID PHONE WITH MLB.COM AT BAT HAS VERSION 5.1.3 OR LOWER PLEASE RECOMMEND THAT THEY UPDATE THEIR APP TO VERSION 5.2 OR HIGHER AND RETEST FOR THE CUSTOMER SYMPTOM. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.

may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.

SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages  SYNC.

ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB  SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB  SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.

If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.

P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

If a low refrigerant charge is confirmed and there are no other obvious signs of a refrigerant leak, suspect the evaporator to be the source of the leak.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

Before replacement of exhaust system components for this issue, align the exhaust system following the workshop manual (WSM) procedure found in section 309-00, Muffler and Tailpipe removal and installation. The WSM procedure has been revised with updated steps to resolve these issues.

P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

THIS PART WAS NOT INITIALLY RELEASED FOR SERVICE. THIS PART IS NOW AVAILABLE FOR SERVICE AND WORKSHOP MANUAL PROCEDURES ARE NOW AVAILABLE IN SECTION 309-00D. THE SERVICE PART NO. IS FR3Z-5K245-A.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.

transmission may exhibit a clunk or ping noise from the driveshaft when shifting from reverse to drive or drive to reverse. A revised driveshaft which has enhanced NVH characteristics has been released. For claiming, use causal part 4R602 and applicable labor operations in section 04 of the service labor time standards (SLTS) manual.

This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.

This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, replace the output shaft flange.

This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. Follow the Service Procedure steps to correct the condition.

This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.

This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 'C to 5 'C (23 'F to 41 'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.

CRANK CONDITION DUE TO THE CLUTCH PEDAL POSITION (CPP) SWITCH BEING DAMAGED. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

Letter

This may be due to a detached A-pillar body seal. Follow the service procedure to repair the vehicle.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

bumper cover meets the rear quarter panels on either side of the vehicle. This may be due to the method used to fasten the rear bumper cover to the vehicle. Follow the Service Procedure steps to correct the condition.

near the rear glass due to broken tension rod clips. Follow the Service Procedure steps to correct the condition.

RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

This may be due to the mating surface between the seat frame and floor pans. To correct this condition, follow the Service Procedure to clean the mating surface.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

FRONT SPLITTER ON THE GT350R MODELS DURING PRE-DELIVERY INSPECTION (PDI). INSTALLATION INSTRUCTIONS CAN BE FOUND ON THE PROFESSIONAL TECHNICIAN SOCIETY (PTS) WEBSITE UNDER THE PDI TAB FOR EACH OF THE MODELS. THERE IS ALSO A LINK WITHIN THE INSTRUCTIONS FOR EACH OF THE VEHICLES TO A VIDEO DEPICTING THE INSTALLATION. FAILURE TO PROPERLY INSTALL THE SPLITTER COULD RESULT IN DAMAGE TO THE SPLITTER OR OTHER COMPONENTS DURING OPERATION OF THE VEHICLE.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

The vehicles should not have the brake rotors machined when servicing the brake system. Replacement of brake rotors is the only acceptable service of brake rotors on GT350 and GT350R vehicles. GT350 and GT350R vehicles are equipped with a brake system designed for high speed and superior fade resistance. Occasional brake squeal and elevated levels of brake dust may occur. This is normal and does not affect brake system performance. Refer to the Workshop Manual (WSM) Section 206-00 and the Mustang Owner's Manual and the Shelby GT350 Owner's Manual Supplement for further information.

This condition is most apparent at the front outer corners of the lower seat cushion. This may be due to the seat cover coming loose. This can be corrected by tucking the corners of the seat cushion underneath the seat cover. Any loose seat cover material can also be tucked under the cover. Replacement of the seat cushion cover is not necessary to correct this condition.

This may be due to improper removal and installation of the drive pinion flange. It is critical to reinstall the drive pinion flange in the same orientation on the drive pinion stem as it was before it was removed. Mark the drive pinion flange and the drive pinion stem before removing the flange to make sure that it is reinstalled on the stem in the same orientation as it was before removal. Refer to Workshop Manual (WSM), Section 205-02.

surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position. If the tonneau covers have been installed on the vehicle, and the wear/damage is located in the area where the tonneau covers overlap the convertible top, replace the convertible top material. Refer to WSM, Section 501-18. Discard the original tonneau covers, and supply the customer with new tonneau covers, part numbers FR3Z-7631004-CB and FR3Z-7631005-CB. For claiming, use causal part 7631004 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.

surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position. If the tonneau covers have been installed on the vehicle, and the wear/damage is located in the area where the tonneau covers overlap the convertible top, replace the convertible top material. Refer to WSM, Section 501-18. Discard the original tonneau covers, and supply the customer with new tonneau covers, part numbers FR3Z-7631004-CB and FR3Z-7631005-CB. For claiming, use causal part 7631004 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.

affected vehicles, a front door latch may open to the secondary latched position while driving. While the door is in the secondary latched position the driver will notice wind noise from the door and a door ajar warning will appear on the instrument cluster. This concern does not result in a fully opened door while driving. The occupant can open the door normally using the door handle.

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

which appear to have worn treads even when the tires are new or have low miles. This may be due to the fact that these tires come from the factory with a tread design which has shallower tread depth than most tires. There are also fewer grooves molded into the surface of the tire, with some areas of the tire showing no tread at all. Before condemning these tires as excessively worn, ensure that you are familiar with how these tires appear when new.

(50-70MPH) AND IS PERCEIVED AS A TREMOR IN THE FLOOR PAN, SEAT TRACK, OR STEERING WHEEL AND MAY BE HEARD AS A RUMBLE, HUM, OR BOOM. BEFORE REPLACEMENT OF ANY PARTS BE SURE TO VERIFY THE CONCERN WITH A ROAD TEST AND VISUALLY INSPECT THE DRIVESHAFT FOR DAMAGE, UNDERCOATING, INCORRECTLY SEATED UNIVERSAL JOINTS, ROTATE THE DRIVESHAFT BY HAND TO FEEL FOR ANY BINDING OR END PLAY IN THE UNIVERSAL JOINTS. IF NO CONCERN IS FOUND CHECK AND CORRECT ANY TIRE BALANCE ISSUES USING LOADED HUNTER ROAD FORCE METHOD. IF A CONCERN IS STILL PRESENT BALANCE THE DRIVESHAFT USING THE MASTERTECH SERIES MTS 4000 DRIVELINE BALANCE AND NVH ANALYZER. REFER TO WORKSHOP MANUAL SECTIONS 100-04,200-04A AND 205-01. USE LABOR OPERATION 1007D AND ANY APPROPRIATE COMBINATIONS.