2025 Ford Mustang Mach E TSBs

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 10654C, 12651D and 12651D4.

Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Module slider in the event a bind condition occurs allowing park to be engaged."

These warnings occur due to external charging station failures rather than internal module issues.

feature code HTHAH) built on or after 23-Jun-2023 may exhibit a condition where the displayed high voltage (HV) battery state of charge (SOC) percentage has a sudden reduction greater than 10% while driving. At low SOC, this may also result in a reduction of vehicle power with a turtle light displayed in the cluster. This concern may occur if the vehicle has not been charged to 100% for an extended period of time as this leads to an inaccurate displayed SOC. Advise customers to charge their vehicle to 100% at least once per month to reset the SOC measurement or more often if the condition persists. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

with diagnostic trouble code (DTC) U3000:49 with a status byte of 8F stored in the camera module-rear (CMR). This may be due to the CMR software level. NOTE: The driver status monitor camera module may also be called camera module-rear.

diagnostic trouble code (DTC) P0B24 stored in the battery energy control module (BECM). This may be due to the BECM software level. ****Additional Model Information: equipped with extended range battery*****

control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.

the frunk for possible contact with the radiator outlet overflow cooling line clamp. If the harness is found to be too close or is touching the overflow cooling line clamp, a retaining clip is to be installed to reposition the wiring harness

battery with minor feature code HTHAH may exhibit an illuminated powertrain malfunction indicator (wrench) lamp with the DTC P0C28 stored in the SOBDMC

codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occurring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure in the GWM tool box, not in the toolbox of the module with the DTC's, to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific vehicle identification number (VIN), refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.

codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occuring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific VIN, refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.

Reason for update: * Update the Service Procedure to: - Remove Step related connecting a battery charger - Add Step 7 and Step 29 along with Figure 4 to include mass damper remove and install. * Update the Parts list: - Updated to include rear electric drive assembly studded bolts and nuts to secure the mass damper. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Stuck in park * "Service Vehicle Soon" message in the instrument panel cluster (IPC) * Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E6:71 stored in the secondary on-board diagnostic control module C (SOBDMC) This may be due to high ground resistance of the park pawl motor.

feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026. If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number VIN required) and fill out the form. Do not use the "Report A Problem" link to submit a report for

feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026.<br /><br /> If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number VIN required) and fill out the form. Do not use the "Report A Problem" link to submit

distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q3 of 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS

flashing light on the air conditioning (A/C) button with a lack of heat and/or A/C with diagnostic trouble code (DTC) B1717:06 stored in the heat pump valve control module (HPVCM). This may be due to the software in the HPVCM. To correct the condition, reprogram the HPVCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the DTC remains this may be due to the "Heat Pump Vacuum Lock Release Sequence" application performance in the Ford Diagnosis and Repair System (FDRS). The "Heat Pump Vacuum Lock Release Sequence" application has been updated in FDRS to operate properly. For claiming, use causal part 14H266 and labor operations 12651D and 12651D4.

exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.

wireless Apple CarPlay or wireless Android Auto. This may be due to wireless interference. To isolate the wireless interference as a possible cause, turn off the wireless projection application in SYNC Connectivity settings in the vehicle's center touch screen and connect the phone through universal serial bus (USB) cable. If the call quality issue through Apple CarPlay or Android Auto is addressed, this confirms that wireless projection was the cause. Engineering is aware of this condition and working on a software solution expected at the end of Q4 2026. As a temporary solution, customers can connect their phones with a USB cable. Reprogramming or replacement of any modules will not correct the condition. Use the "Submit Global Concern Report (GCR)" link at the upper right of the OASIS report to submit a vehicle concern report if the wireless projection is found to be the cause of the condition.

in park * "Service Vehicle Soon" message in the instrument panel cluster (IPC) * Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E6:71 stored in the secondary on-board diagnostic control module C (SOBDMC) This may be due to high ground resistance of the park pawl motor.

distorted or blurry 360 degree camera image in the center display screen, but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q2 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

blurry 360 degree camera image in the center display screen but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected by the end of 2025. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

control symptoms with diagnostic trouble code (DTC) B1717:06 in the heat pump valve control module (HPVCM). Workshop Manual (WSM), Section 412-00 Climate Control System - General Information > Diagnosis and Testing > Pinpoint Test AW has been updated to address this condition. Refer to the revised WSM section for normal diagnosis.

The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.

Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.

This may be due to an alignment issue with the hood. The most common adjustments to improve closing efforts involve the hood front up and down alignment and the bump stop rubbers. Refer to Workshop Manual, Section 501-03 Body Closures > General Procedures > Hood Alignment for procedures on proper adjustments that can improve front luggage compartment hood closing efforts.

commanded from the exterior of the vehicle following a future over-the-air update. This is not addressing any existing condition in the field."

commanded from the exterior of the vehicle following a future over-the-air update. This is not addressing any existing condition in the field."

Reason for update: Add 2022-2025 Transit vehicles. Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display screen after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

customers use the monostable shifter."

(DTC) C1013:92 stored in the anti-lock brake system (ABS) module. This may be due to brake pads being out of specification for compressibility, which can alter the brake system's pressure-volume and falsely indicate an internal hydraulic failure. The pinpoint test for C1013:92 in the Workshop Manual (WSM), Section 206-09 has been updated to include a preliminary inspection and a brake pad swap to determine if an out of specification set of brake pads are the root cause.

defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a

defrost features will not turn on after a remote start is performed through the FordPass application or the key fob.

This may be due to a deformed speaker cone.

the instrument panel cluster (IPC). This may be due to the software in the IPC.