2024 Ford Mustang Mach E TSBs

This may be due to the body control module (BCM) software. To correct the condition, download and run the "BCM - Programmable Module Installation (PMI)" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. If the condition persists after PMI, refer to Workshop Manual (WSM), Section 417-01 for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and BCM.

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

in the power steering control module (PSCM) after a self test is performed with the Ford Diagnosis and Repair System (FDRS) scan tool. If the vehicle does not exhibit any observable symptoms such as lack of/reduced power steering assist, disabling of power steering assist features and/or power steering assist fault messages displayed on the instrument panel cluster (IPC), this DTC should be ignored. No further service action is required.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Module slider in the event a bind condition occurs allowing park to be engaged."

These warnings occur due to external charging station failures rather than internal module issues.

with phone-as-a-key may exhibit various phone-as-a-key concerns with diagnostic trouble codes (DTC) U200D:15, U200E:15, U200F:15, B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 stored in the remote function actuator (RFA) module. If any of these DTCs are detected during diagnostics, clear the DTCs, reprogram the RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 DTCs return in the RFA after a self-test, follow normal Workshop Manual (WSM) diagnostics in Section 419-01. Repair as necessary outside of this article. For claiming, use causal part 14G617 and labor operations 12651D and 12651D4.

feature code HTHAH) built on or after 23-Jun-2023 may exhibit a condition where the displayed high voltage (HV) battery state of charge (SOC) percentage has a sudden reduction greater than 10% while driving. At low SOC, this may also result in a reduction of vehicle power with a turtle light displayed in the cluster. This concern may occur if the vehicle has not been charged to 100% for an extended period of time as this leads to an inaccurate displayed SOC. Advise customers to charge their vehicle to 100% at least once per month to reset the SOC measurement or more often if the condition persists. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.

with diagnostic trouble code (DTC) U3000:49 with a status byte of 8F stored in the camera module-rear (CMR). This may be due to the CMR software level. NOTE: The driver status monitor camera module may also be called camera module-rear.

module to get stuck in bootloader"

Ford and Lincoln vehicles equipped with a B&O audio system may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). This may be due to software in the digital signal processing (DSP) module. To correct this condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.

control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.

battery with minor feature code HTHAH may exhibit an illuminated powertrain malfunction indicator (wrench) lamp with the DTC P0C28 stored in the SOBDMC

properly goes to sleep "

malfunction (wrench) indicator with diagnostic trouble code (DTC) P0ADA stored in the battery energy control module (BECM). This may be due to the BECM software level.

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

Audio Control Module (ACM) Software Update

front when using adaptive cruise control (ACC) or BlueCruise. This may be due to the front bumper affecting both corner radar sensor signals.

battery does not charge while using a DC fast charger level 3 and a charge error message displayed on the charger with DTC U049C stored in the BECM.

code (DTC) U3000:49 stored in the camera module rear (CMR).

-Reduces Telematics Control Unit based Key Off Load battery drain. - Map orientation improvement - removes false"IP Configuration Failure" message when wrong WiFi password is entered. - Improves functionality of Stolen Vehicle Services

accessory protocol interface module (APIM) software updates have been performed.

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

- Reduction in Key off load battery drain via Enhanced Central Gateway (ECG) controlled reset. - Reduction in Key off load battery drain due to Bluetooth Low Energy Module (BLEM) software - Addresses potential lock out condition post OTA update."

- Top off the Low Voltage battery prior to OTA update. (EV only) - Enables Public Charging App function above 5 MPH. - Hides ""Update Now"" button on HMI when the vehicle battery health is below threshold. - Corrects ""Bluecruise Maps not up to date"" erroneous message. - Improves Key Off Load battery drain due to SYNC. "

Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).

vehicles, the charge status indicator (CSI) displays in RED (fault) for a short period after the charge plug is unlocked from the charge port during vehicle level 3 (L3) charging. All vehicles are charged correctly and no warning shows in the instrument cluster.

accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.

failure with a message displayed in the Ford Diagnosis and Repair System (FDRS) scan tool indicating Procedure Unsuccessful-Flash Software Failed To Flash. This may be due to the ACM programming routine. To correct this condition, download and click the refresh icon located next to the run icon to update the ACM - Programmable Module Installation (PMI) app. For claiming, use causal part 18C869 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.

an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Quality Improvements include - FordPass will remember last known profile. - Allow customers to exit during OTA update. - Improves BCM response to de-inhibit request when OTA is complete. - Allows vehicle to return to sleep after detecting CAN traffic, for reduced battery drain. - Perimeter alarm duty cycle for horn and light aligned with non -US market requirements. (ECE-116)

stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B.

Reason for update: * Update the Service Procedure to: - Remove Step related connecting a battery charger - Add Step 7 and Step 29 along with Figure 4 to include mass damper remove and install. * Update the Parts list: - Updated to include rear electric drive assembly studded bolts and nuts to secure the mass damper. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Stuck in park * "Service Vehicle Soon" message in the instrument panel cluster (IPC) * Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E6:71 stored in the secondary on-board diagnostic control module C (SOBDMC) This may be due to high ground resistance of the park pawl motor.

feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026. If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number VIN required) and fill out the form. Do not use the "Report A Problem" link to submit a report for

after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.

feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026.<br /><br /> If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number VIN required) and fill out the form. Do not use the "Report A Problem" link to submit

distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q3 of 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS

wireless Apple CarPlay or wireless Android Auto. This may be due to wireless interference. To isolate the wireless interference as a possible cause, turn off the wireless projection application in SYNC Connectivity settings in the vehicle's center touch screen and connect the phone through universal serial bus (USB) cable. If the call quality issue through Apple CarPlay or Android Auto is addressed, this confirms that wireless projection was the cause. Engineering is aware of this condition and working on a software solution expected at the end of Q4 2026. As a temporary solution, customers can connect their phones with a USB cable. Reprogramming or replacement of any modules will not correct the condition. Use the "Submit Global Concern Report (GCR)" link at the upper right of the OASIS report to submit a vehicle concern report if the wireless projection is found to be the cause of the condition.

in park * "Service Vehicle Soon" message in the instrument panel cluster (IPC) * Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E6:71 stored in the secondary on-board diagnostic control module C (SOBDMC) This may be due to high ground resistance of the park pawl motor.

distorted or blurry 360 degree camera image in the center display screen, but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q2 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

remain active and deactivates immediately. This may be due to the audio control module (ACM) configuration. To restore the functionality of this feature, download and run the "ACM - Enable Engine Sound Enhancement and Active Noise Control" application in the Ford Diagnosis and Repair System (FDRS) scan tool. In cases where the ACM is replaced, this routine will run during the "ACM - Programmable Module Installation (PMI)" application. Make sure to follow the FDRS on-screen instructions carefully. For claiming, use causal part 18C869 and labor operation numbers 12651D and 12651D4.

blurry 360 degree camera image in the center display screen but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected by the end of 2025. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

code (DTC) U3000:49 stored in the camera module rear (CMR). This may be due to the software level of the CMR. Inform customers that engineering is currently working on a solution for this condition that is expected in Q3 2025. Monitor Professional Technician System (PTS) for additional information.

Mach-E vehicles when attempting to charge/balance high voltage battery modules (arrays) from remanufactured array kits, the Midtronics xMB tool will not recognize the remanufactured part number.

The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.

Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.

This may be due to an alignment issue with the hood. The most common adjustments to improve closing efforts involve the hood front up and down alignment and the bump stop rubbers. Refer to Workshop Manual, Section 501-03 Body Closures > General Procedures > Hood Alignment for procedures on proper adjustments that can improve front luggage compartment hood closing efforts.

commanded from the exterior of the vehicle following a future over-the-air update."

Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.

following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.

At this time, there is no corresponding owner letter or repair procedure. We are evaluating a potential paint quality concern.

vehicles tire sealant and inflator kit, the system will not provide sealant or air to inflate and seal the tire. The air-only function will operate as expected.

may experience the overhead console sunglass bin cannot be locked in a closed position.

Some 2021-2024 Mustang Mach-E vehicles built on or before 09-Jul-2024 may exhibit a wind noise from the exterior mirrors/A-pillar area when driving between 25 mph-40 mph (32 km/h-64 Km/h). This may be due to poor sealing of the lower mirror foam and the glass top run foam. To correct this condition, follow the Service Procedure to install new lower inner foam and the glass top run foam.

This may be due to a deformed speaker cone.

showing ""Hardware problem"""

system performance/stability/intermittent system reboot * Intermittent wireless Apple CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through Apple CarPlay and Android Auto * Alexa function consistency and stability

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

Reason for update: Add 2022-2025 Transit vehicles. Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display screen after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

on or before 22-May-2025<br /> * 2024 Maverick vehicles built on or after 17-Jan-2024<br /> <br /> Some of the above vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct the condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and labor operation numbers 7001D and 7001D4.

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

AP-time.

- 23 MY Minor quality fixes in Enhanced Central Gateway (ECG) Software, not affecting vehicle operation. - Addresses potential unintended lock out of vehicle after OTA update.

Maverick Vehicles Drivers Side Seat Buckle Replacement

Improves OTA deployment reduce FTDI risk.

(DTC) C1013:92 stored in the anti-lock brake system (ABS) module. This may be due to brake pads being out of specification for compressibility, which can alter the brake system's pressure-volume and falsely indicate an internal hydraulic failure. The pinpoint test for C1013:92 in the Workshop Manual (WSM), Section 206-09 has been updated to include a preliminary inspection and a brake pad swap to determine if an out of specification set of brake pads are the root cause.

charging status indicator fault (red light) after the charge gun is unlocked - Addresses potential false thermal protection Diagnostic Trouble Codes that may cause the Direct Current fast charging to stop"

- 21 MY: Removes erroneous ""Reverse Brake Unavailable"" message.

defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a

defrost features will not turn on after a remote start is performed through the FordPass application or the key fob.

Mustang Mach-E Vehicles Undesired Acceleration Due to Adaptive Cruise Control (ACC) Activation

available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.