2013 Ford Fusion TSBs

Ford is voluntarily conducting this program to evaluate the software currently installed on one or more electronic modules in the affected vehicles.

Some 2013-2016 Escape 2014-2016 Fiesta ST, and 2013-2014 Fusion vehicles equipped with a 1.6L Gasoline Turbocharged Direct Injection (GTDI) engine may exhibit a lack of power concern with malfunction indicator lamp (MIL) illuminated and diagnostic trouble codes (DTCs) P0234, P0245, P0246 and/or P0299 stored in powertrain control module (PCM) MEMORY.

and/or a loss of engine RPM after refueling. Some vehicles may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1450 and/or P0456 stored in powertrain control module (PCM) memory.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.

electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual

Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

and equipped with a TCU may exhibit inoperative remote features via MyFord Mobile app, discharged battery, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU field service actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 104.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

(GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

ENGINE AND BUILT ON 9/1/2012 AND THROUGH 8/1/2013 MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO ENGINE OIL MIGRATING FROM THE VARIABLE VALVE TIMING (VVT) OIL CONTROL SOLENOIDS THROUGH THE ENGINE WIRE HARNESS TO THE CATALYST MONITOR SENSOR (CMS). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

UPDATED WORKSHOP MANUAL (WSM) SECTION 303-03 COOLING SYSTEM

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

CONCERNS INCLUDING: SPEAKER STATIC WITH KEY-OFF, NO AUDIO AFTER VEHICLE IS FIRST STARTED WITH DIAGNOSTIC TROUBLE CODE (DTC) U0184, NO VOLUME CONTROL, OR A STUCK CD WITH NO SLOT BLOCKAGE. PRIOR TO STARTING NORMAL DIAGNOSIS FOR ANY OF THESE CONDITIONS, VERIFY THE ACM IS AT THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE THE APPLICABLE LABOR OPERATION IN SECTION 11 OF THE SLTS MANUAL AND CAUSAL PART 18C869 WHEN CLAIMING THIS REPAIR.

system volume during a reverse park aid chime event. This feature was not implemented for 2013 model year. SERVICE PROCEDURE 1. Is the vehicle equipped with MyFord Touch and a 4.2 inch instrument cluster display? a. Yes - reprogram the instrument panel cluster (IPC) to the latest calibration using Integrated Diagnostic System (IDS) release 99.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. b. No - replace the IPC. Use the chart below for replacement.

2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.

injection (GTDI) engine and built on 9/1/2012 and through 8/1/2013 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2096 (post catalyst fuel trim system too lean bank 1) stored in powertrain control module (PCM) memory. This may be due to engine oil migrating from the variable valve timing (VVT) oil control solenoids through the engine wire harness to the catalyst monitor sensor (CMS).

HESITATION DUE TO POSSIBLE HYDRAULIC CIRCUIT DRAIN. MODEL 2013-16 VARIOUS VEHICLES. *PE

SELECT DOCUMENT SEARCH BUTTON BELOW. FORD FUSION 2013-2015 AND MKZ, 2015 EDGE VEHICLES: SAFETY RECALL SUPPLEMENT FOR 15S14 DATED JULY 10,2015. RECALL INVOLVING STEERING GEAR MOTOR BOLT CORROSION. *LJ UPDATED 10/27/15. *PE

MODEL 2013 FUSION S, SE. *PE

MODEL 2013-2014 FUSION, MKZ. *PE

INTERMITTENTLY AND BODY CONTROL MODULE (BCM) NEEDS REPROGRAMMING TO LATEST CALIBRATION. MODEL 2013-2014 FUSION, MKZ. *PE

POSITION AND HEADLAMPS ARE ON NORMALLY. MODEL 2013-2014 FUSION TITANIUM, MKZ. *PE

CONNECTIVITY AND MALFUNCTION INDICATOR LAMP (MIL) OR WRENCH LIGHT WILL ILLUMINATE. MODEL 2009-2013 FUSION, MILAN, ESCAPE, MARINER. *PE UPDATED 5/7/14. *PE

HEATER AND LAMPS TURN OFF WITHIN NO MORE THAN THREE DRIVE CYCLES AFTER UNPLUGGING ENGINE BLOCK HEATER. MODEL 2013-2014 C-MAX, FUSION, MKZ HYBRID/ENERGI. *PE

POWERTRAIN CONTROL MODULE (PCM), THAT NEEDS TO BE REPROGRAM WITH LATEST CALIBRATION. MODEL 2013 C-MAX, 2014 FUSION. *PE

MODELS 2013 MKZ, C-MAX, FUSION. *PE

TROUBLE CODE P0053/P0054 (HEGO HEATER CODE), MAY BE SET. MODELS 2013 C-MAX, FUSION, MKZ HYBRID/ENERGI. *PE

CAMSHAFT TIMING (VCT) OIL CONTROL SOLENOIDS AND PCV HOSE, WITH MIL LIGHT ON. MODELS 2013 FUSION, ESCAPE. *PE

(PCM) DUE TO COOLANT BYPASS SOLENOID C FAULT, LOCATED REAR OF ENGINE. MODEL 2013 FUSION. *PE

MODELS 2013 FUSION, ESCAPE. *PE

being expanded to include VINs in the state of Texas in an effort to increase the number of parts returned for research.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

Information

vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Ford is voluntarily conducting this program to replace certain airbag modules manufactured by Takata Corporation on vehicles always registered and always residing in Florida. The replacement module being installed contains an inflator that was manufactured by a different supplier (does not contain a Takata inflator) and does not contain ammonium nitrate. The purpose of this program is to obtain field parts for testing and evaluation.

Ford is voluntarily conducting this program to replace certain airbag modules manufactured by Takata Corporation on vehicles always registered and always residing in Florida. The replacement module being installed contains an inflator manufactured by a different supplier (does not contain a Takata inflator) and does not contain ammonium nitrate. The purpose of this program is to obtain field parts for testing and evaluation.

This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

When this occurs, perform Module Reprogramming in IDS. If not prompted to enter as-built data, perform As-Built programming to finish configuring the FCIM. FCIM service stock is transitioning to the 2015 model year level FCIM, and the as-built data on the server has been updated for 2013-2014 model year vehicles to include an extra line of data to accomodate the change. However, some older FCIMs may still be received from service stock. If an older level FCIM is being installed, the PMI may fail and performing Module Reprogramming will correct the concern. Normal PMI procedure will complete on a 2015 FCIM.

If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.

(PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.

with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

THE WINDOW STICKER INDICATES 0-19 MILE RANGE FOR 2013-2016 CMAX/FUSION ENERGI. VARIATION OF EV RANGE MAY NOT INDICATE A BATTERY OR CHARGING CONCERN. EV RANGE IS SIMILAR TO THE DTE DISPLAY ON GASOLINE VEHICLES, EV RANGE WILL VARY WITH DRIVING/OPERATING CONDITIONS. CONDITIONS INCLUDE: EXTREME OUTSIDE TEMPERATURES, TERRAIN, DRIVING STYLE, CITY OR HIGHWAY DRIVING, TIRE PRESSURE, AND USE OF ACCESSORIES. IF THE CUSTOMER REPLACES THE LOW ROLL RESISTANCE TIRES WITH A MORE AGGRESSIVE TREAD THE RANGE WILL SUFFER. USING THE CABIN HEATER AND A/C, WHICH ARE ELECTRIC, WILL ALSO DECREASE EV RANGE. TO TEMPORARILY REMOVE THE IMPACT OF DRIVING/CLIMATE HISTORY, RESET THE LIFETIME SUMMARY OR DRIVING HISTORY BY USING THE SETTINGS MENU ON THE LEFT SIDE OF THE INSTRUMENT CLUSTER, UNDER DISPLAY

(DTC) REGARDING EVAPORATIVE EMISSIONS LEAK DETECTION CONTROL MODULE AND POSSIBLE REPLACEMENT, IF CORROSION IS FOUND. MODEL 2013-15 FUSION, MKZ HYBRID. *PE

MALFUNCTION INDICATOR LAMP WOULD ILLUMINATE DUE TO VARIOUS RESETS OF MODULES. MODEL 2013-16 FUSION, MKZ, 2013-15 C-MAX, 2015 F-150, MKC. *PE

TOUCH) VEHICLES WILL DEFAULT TO ICE BLUE AFTER THE IGNITION SWITCH CYCLE. *PE

MODEL 2013-15 FUSION, MKZ. *PE

INOPERATIVE AFTER BATTERY DISCONNECT OR COMPONENT SERVICE. *TA

MODEL 2013-14 FUSION, MKZ, 2015 MKC. *PE

CODES (DTC) U0401 AND/OR U0402 IN SIDE OBJECT DETECTION (SOD) MODULES NEED TO BE CORRECTED. MODEL 2013-14 FUSION, MKZ. *PE

MALFUNCTION INDICATOR LAMP ILLUMINATING (MIL) AND INFORMATION PROVIDED TO CORRECT THE ISSUE. MODEL 2013 ESCAPE, FUSION. *PE

WHERE VEHICLE EXHIBIT DIAGNOSTIC TROUBLE CODES (DTC) BO0D5:A4 AND B1202:A4. MODEL 2013-14 FUSION. *PE

(PCM) MEMORY AND CAUSES MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE. MODEL 2013 ESCAPE, FUSION, MKZ. *PE

(DTC) P06B8, IN POWERTRAIN CONTROL MODULE, WILL NOT BE CLEARED. MODEL 2013 C-MAX, FUSION, MKZ. *PE

IMPROVED COOLING FAN CIRCUIT DUE TO A LACK OF AIR CONDITIONING, A MALFUNCTIONING INDICATOR LAMP (MIL) AND OVERHEATING. *PE

WHICH LEADS TO CARBON CANISTER SATURATED WITH LIQUID FUEL AND A FUEL ODOR, SLOW FILL, OR HESITATION OR STUMBLE, OCCURS WHILE DRIVING. MODEL 2013 EXPLORER, TAURUS, MKS, FLEX, MKT, FUSION, MKZ, POLICE INTERCEPTOR, AND SEDAN. *PE

MODULE (BECM) WILL NEED REPROGRAMMING TO LATEST CALIBRATION DUE TO STORAGE OF DIAGNOSTIC TROUBLE CODES (DTC) P0ADC, P0AE0 AND/OR P0AE7. MODEL 2013 C-MAX, 2013-2014 FUSION, MKZ. *PE

TO MAINTAIN A CHARGE OR BECOMES DISCHARGED WHEN OPERATED AT MAXIMUM ELECTRICAL LOADS FOR SHORT CYCLE DRIVE. MODELS 2013 C-MAX, FUSION, MKZ. *PE

VEHICLES, OR RECALL FUNCTION FOR MEMORY SEAT MAY BE INOPERATIVE DURING PASSIVE ENTRY. MODELS 2013 MKZ, FUSION. *PE

DRIVABILITY ISSUES SUCH A POSSIBLE INTRUSION OF WATER IN CONNECTORS. MODELS 2013 C-MAX, FUSION/MKZ HYBRID/ENERGI. *PE

CYCLE, OR SLOW NAVIGATION CALCULATIONS, DUE TO AMOUNT OF DATA, WITHIN SIZE OF CONTACT LIST, CREATING PROCESSING PROBLEM FOR MODULE DURING KEY ON CYCLE. MODELS 2011-2013. NO MODEL LISTED. *PE

INTERFACE MODULE (FDIM), TOUCHSCREEN CALIBRATION MUST BE PERFORMED. MODEL YEARS 2011-2013. NO MODELS LISTED. *PE

INFORMATION REGARDING EXTENDED WARRANTY FOR COVERING ACCESSORY PROTOCOL INTERFACE MODULE REGARDLESS OF MILEAGE. MODELS 2011-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, MKZ, F-150, F-SUPER DUTY. *PE

Bushing Inspection and Protective Service Cap Installation

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.

thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.

HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.

exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.

exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.

power, or stall when placed in gear with DTCs P00C6, P0087, P008A, P008B, P018C, or P018D. If normal diagnosis leads to a biased or failed Fuel Low Pressure (FLP) sensor, the sensor is available without the need to order the entire fuel line assembly. The FLP sensor, located on the fuel supply line to the high pressure pump, provides the low side fuel pressure input to the PCM so the Fuel Driver Module can be controlled accordingly. The FLP PID can be viewed in the Datalogger and then compared to a manual pressure gauge per pinpoint test HC in the PCED to validate the sensor is working properly. The Fusion/MKZ catalog has been updated to show the sensor availability.

exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. Follow the Service Procedure steps to correct the condition.

clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.

published that lists either a 2.56 or 2.57 axle ratio. For service and parts ordering purposes, both are the same. The difference in the displayed ratio originates from rounding differences between systems which results in the discrepancy.

15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving, but will not be present when the vehicle is stationary or in Park. Follow the Service Procedure steps to correct the condition.

8/15/2015 MAY EXHIBIT A THUMPING/RUBBING OR GRINDING NOISE COMING FROM THE TRANSMISSION. THE NOISE MAY BE PRESENT IN ALL GEAR RANGES INCLUDING NEUTRAL WHEN THE VEHICLE IS MOVING, BUT WILL NOT BE PRESENT WHEN THE VEHICLE IS STATIONARY OR IN PARK. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

Escape, 2009-2011 Mariner, 2010-2014 Fusion, 2010-2011 Milan, 2012-2014 Edge/Explorer, and 2013-2014 Taurus/MKT/MKZ vehicles built on or before 10/14/2013 and equipped with a 6F35 automatic transmission may exhibit a fluid leak from the left hand (LH) transmission halfshaft seal due to wear on the transmission case bushing.

IS MOVING AND NOT PARK OR STATIONARY. MODEL 2013-C-MAX, FUSION, MKZ. *PE

2009- 2011 MARINER, 2010-2011 MILAN. SOME VEHICLES EQUIPPED WITH 6F35 AUTOMATIC TRANSMISSION MAY EXHIBIT A FLUID LEAK FROM THE LEFT HAND TRANSMISSION HALFSHAFT SEAL DUE TO WEAR ON THE TRANSMISSION CASE BUSHING. *LJ

2013 C-MAX, 2013-2014 FUSION, MKZ. *PE

GREASE APPLIED TO TORQUE CONVERTER HUB OR RUST INHIBITOR APPLIED TO FLEXPLATE AT TIME OF MANUFACTURING. MODEL 2013-2014 ESCAPE, FUSION. *PE

MODEL 2013-2014 ESCAPE, FUSION, EDGE, EXPLORER, TAURUS, MKT, MKZ. *PE

EXPERIENCE A LEAKAGE OF FLUID FROM LEFT HAND (LH) HALFSHAFT SEAL. MODEL 2013 ESCAPE, FUSION, EDGE, EXPLORER, TAURUS, MKT, MKZ. *PE

HEARD LIKE POP, TING, CLICK, COMING FROM FRONT WHEEL AREA. MODEL 2013 FUSION. *PE

MODULE (PCM) AND/OR TRANSMISSION CONTROL MODULE (TCM). MODELS 2013 FUSION, MKZ. *PE

Some 2013-2014 Fusion and 2013-2020 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions. This may be due to water intrusion into the exterior mirror connector. To correct the condition, follow the Service Procedure steps to remove the 16 pin connector and install two weather tight 8 pin connectors.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

conditions due to moisture in the exterior mirror connector. Follow the Service Procedure steps to correct the condition.

conditions due to moisture in the exterior mirror connector. Follow the Service Procedure steps to correct the condition.

HOOD, 5 CM (2 INCHES) FROM HEADLAMP FASCIA POINT ON BOTH SIDES. MODEL 2013-16 FUSION. *PE

NOT YET OBSTRUCTING DRIVER'S VIEW. MODEL 2013-14 FUSION. *PE

PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

MODEL 2012-2013 FOCUS. *PE

MODEL 2013 FUSION, MKZ. *PE

IN SOME VEHICLES, A WRINKLE CONDITION AROUND MOON ROOF OPENING IS DUE TO A THERMAL EXPANSION ON GLUE, AND OTHER BONDED COMPONENTS, TO BACKSIDE OF HEADLINER. MODELS 2013 FUSION. *PE UPDATED 10/25/13. *PE

ON CERTAIN VEHICLES, ORDERED ACCESSORIES (REMOTE START, ALL WEATHER FLOOR MATS, CARGO NET) MAY NOT BE INCLUDED, AS IDENTIFIED IN OPTIONAL EQUIPMENT OF MONRONEY LABEL (WINDOW STICKER) AND NEED TO BE INCLUDED BEFORE DELIVERY. MODELS 2013 FUSION, MKZ. *PE UPDATED 10/22/13. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

Front Brake Flexible Hose Replacement Submitting Owner Letters

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

WHICH AFFECTS DOOR AJAR, PARKING BRAKE OR PARKING AID AND AUDIO CONTROL MODULE (ACM) NEEDS REPROGRAMMING TO LATEST SOFTWARE VERSION. MODEL 2013-14 FUSION, MKZ. *PE

DISABLE OBDII SYSTEM MONITORS FOR PCM REPROGRAMMING. MODEL 2011-14 F-SUPER DUTY, ESCAPE, TAURUS, FUSION, MKT, MKZ. *PE

SENSOR (OSS) SIGNAL FAULTS, A SOFTWARE ERROR HAS OCCUR AND DISABLED ON BOARD DIAGNOSTIC (OBD) MONITORS WITH NO ILLUMINATION OF MALFUNCTION INDICATOR LAMP (MIL). MODEL 2011-2014 F-SUPER DUTY, ESCAPE, TAURUS,FUSION, MKT, MKZ. *PE

If both keys are lost and the original selling dealer does not have the key code on file, a new lock set may be needed. For Fusion IKT (non push-button start) use lock set ES7Z-5422050-A, Fusion push-button start use lock set ES7Z-5422050-B, and for Lincoln MKZ use lock set DP5Z-5422050-A. Kits include pre-cut keys. The push-button start kits come with back-up key blades, but do not include passive key remotes which will need to be ordered separately. Rotunda, the Technical Assistance Center, or the Customer Relations Center will not have key code information.

MKS, MKX, AND 2013-2014 LINCOLN MKT VEHICLES MAY EXPERIENCE PROBLEMS WITH THE CRUISE CONTROL SPEED THAT DOESN'T MATCH THE SPEEDOMETER SPEED. *TA

*PE

MODEL 2013 FUSION, MKZ. *PE

P025A/U0109, P025A/U0109/P0103, P025A/P0103/P1A0C, AS WELL AS STALLING AFTER VEHICLE WAS DRIVEN AND CRANK NO START. MODELS 2013 C-MAX, FOCUS, ESCAPE. *PE

LID THAT FAILS TO REMAIN OPEN, WHEN NEED TO BE. MODEL 2013 FUSION. *PE

The 2013 Fulsion vehicles do not lower the audio system volume during a reverse park aid chime event. This feature was not implemented for 2013 model year.

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB  SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB  SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

U049A-B6 OR U0501-86, IN INSTRUMENT CLUSTER. MODEL 2013 FUSION, MKZ. *PE

INOPERATIVE, LACK OF OR SLOW RESPONSE TO PHONE AND VOICE BUTTON OPERATION. MODELS 2012-2013 FOCUS, E-SERIES, EDGE, EXPEDITION, FUSION, EXPLORER, F-150, F-250, NAVIGATOR, 2013-2014 FLEX, 2012-2014 FIESTA, MUSTANG, 2013 ESCAPE, C-MAX, TAURUS, 2012 MKZ. *PE

MESSAGE IN DISPLAY AND BOTH REMOTE CONTROL RKE FUNCTIONS ARE INOPERATIVE. MODELS 2013 FUSION, MKZ. *PE

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

THIS MAY BE DUE TO INADVERTENT ACTUATION OF THE FUEL DOOR RELEASE BUTTON BY THE CUSTOMER WHEN EXITING THE VEHICLE. IF THE FUEL FILLER DOOR IS NOT FULLY CLOSED AFTER A REFUELING EVENT, OR THE FUEL FILLER DOOR IS OPEN FROM ERRONEOUSLY PRESSING THE FUEL DOOR RELEASE BUTTON, A MESSAGE DISPLAYS DURING THE THIRD DRIVE CYCLE TO INDICATE THE FUEL FILLER DOOR IS NOT CLOSED AND THE DTC SETS. BEFORE PERFORMING WORKSHOP MANUAL DIAGNOSTICS, CONSULT THE CUSTOMER ABOUT THE POTENTIAL FOR ACCIDENTAL FUEL DOOR ACTUATION AND EXPLAIN THE NEED TO FULLY LATCH THE FUEL DOOR AFTER EVERY REFUELING EVENT.

CAN BE HEARD COMING FROM FUEL TANK AREA. MODEL 2013-14 FUSION, MKZ. *PE

SHOWING EMPTY, AND/OR DISTANCE TO EMPTY 56 KILOMETERS (35 MILES). MODELS 2013 FUSION, MKZ. *PE

MODELS 2013 FUSION, MKZ. *PE

ABLE TO SELECT MENU CLIMATE CONTROL ITEMS OR INSTRUMENT CLUSTER WILL BE GRAYED OUT AND NEED TO BE REPROGRAM, WITH LATEST CALIBRATION, THE FCIM. MODEL 2013-15 FUSION, MKZ. *PE

MODEL 2013-2014 FUSION, MKZ. *PE

MODEL 2013-2014 MKZ, FUSION. *PE

DEFROST IS NOT AVAILABLE IN SETTINGS OF INSTRUMENT CLUSTER. MODEL 2013-2014 FUSION, MKZ. *PE

AVAILABLE IN INSTRUMENT CLUSTER SETTINGS OF REMOTE START MENU. MODELS 2013 FUSION, MKZ. *PE

This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

Follow the Service Procedure steps to correct the condition.

(DTC) B141B and/or B141C

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

POSITION, DUE TO REAR CENTER SAFETY BELT BUCKLED OVER EMPTY SEAT AND FOLDED DOWN. LIFT 60 PERCENT SLIGHTLY, GAIN ACCESS TO CENTER SEAT BELT BUCKLE, RELEASE BELT BUCKLE LATCH AND ALLOW SAFETY BELT TO RETRACT. MODELS 2013 FUSION, MKZ. *PE

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

A SOFTWARE UPGRADE IS AVAILABLE FOR CERTAIN VEHICLES. MODELS 2012-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, F-150. *PE UPDATED 5/10/13. *PE UPDATED 9/17/13. *PE

VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.

MODEL 2013 ESCAPE, FUSION, EDGE, TAURUS, EXPLORER, MKT, MKZ. *PE

FORD 2013-2015 FUSION VEHICLES: CUSTOMER SATISFACTION PROGRAM INVOLVING 18'' GLOSS BLACK PHYSICAL VAPOR DEPOSITION WHEEL REPLACEMENT. *LJ

*PE

MODELS 2013 C-MAX, FUSION ENERGI. *PE