2013 Ford Focus TSBs

Ford is voluntarily conducting this program to evaluate the software currently installed on one or more electronic modules in the affected vehicles.

Automatic Transmission; Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Non-Ford Part Usage: Vehicles that are still covered by the 8 years/80,000-mile Emissions warranty coverage MUST be serviced with a NEW Ford Motor Company TCM. Vehicles outside of or exceeding the 8 years/80,000-mile coverage are authorized to use a used Ford Motor Company TCM, a refurbished original Ford TCM, or an aftermarket TCM that will successfully complete the required Ford software updates.

displayed in the instrument panel cluster (IPC) message center. This may be due to either an internal coolant leak on the upper or lower high voltage battery or corrosion on the lower high voltage battery connector caused by water ingress. If this occurs, the vehicle may not restart once it has been shut off. To resolve the condition, follow the Service Procedure to replace the upper and lower high voltage battery or apply corrosion protection.

This may be due to either an internal coolant leak on the upper or lower high voltage battery or corrosion on the lower high voltage battery connector caused by water ingress. If this occurs, the vehicle may not restart once it has been shut off. To resolve the condition, follow the Service Procedure to replace the upper and lower high voltage battery or apply corrosive protection.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Be aware that the engine oil and DPS6 transmission fluid are similar in color and texture. A transmission fluid leak at the input shaft seal can cause a buildup of fluid in the bell housing; creating the appearance of a rear main seal leak. The rear main seal should only be replaced after a rear main seal failure is confirmed through appropriate diagnostics outlined in the updated online Workshop Manual (WSM) Section 303-00 / Diagnosis and Testing with the use of Fluorescent dye (164-TP33200601).

consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures

or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual

Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

runs rough, crank no-start, loss of power, loss of engine RPM, and/or illuminated MIL with diagnostic trouble codes (DTCs) P0122, P0222, P0320, P0322, P0327, P0332, P0344, P0369, P06A7, P060D, P061C, P1336, P1674, P2111, P2112, P2127 and/or P2135. Follow the Service Procedure steps to correct the condition.

of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013 and/or P0606 will be present or stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.

The suspect service part number is GV6Z-14A068-G. The wrong part will have an engineering number of GV6T-14A073-GD and it will not work. The correct part will have engineering part number of GV6T-14A073-with a suffix of XA, XB, XC, or XF. Dealers should utilize the normal return process of a miss packaged part. Continue to monitor OASIS. When this concern is resolved, an update will be provided.

and equipped with a TCU may exhibit inoperative remote features via MyFord Mobile app, discharged battery, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU field service actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 104.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

SLOW THE OPERATION OF THE LUGGAGE COMPARTMENT DECK LID WHEN OPENING AND CLOSING. THE LUGGAGE COMPARTMENT DECK LID IS HELD OPEN ONLY BY THE COIL SPRINGS CONNECTED TO THE HINGES. THE DAMPENER IS NOT CHARGED WITH GAS TO SUPPORT THE LUGGAGE COMPARTMENT LID LIKE THE 5 DOOR HATCHBACK LIFT CYLINDERS. REFER TO THE UPDATED WORKSHOP MANUAL SECTION 501-03 FOR ADDITIONAL INFORMATION. IT IS NORMAL FOR THE DAMPENER TO COMPRESS EASILY WHEN REMOVED FROM THE VEHICLE, UNLIKE THE HATCHBACK LIFT SUPPORT CYLINDERS.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

ENGINE AND BUILT ON 9/1/2012 AND THROUGH 8/1/2013 MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO ENGINE OIL MIGRATING FROM THE VARIABLE VALVE TIMING (VVT) OIL CONTROL SOLENOIDS THROUGH THE ENGINE WIRE HARNESS TO THE CATALYST MONITOR SENSOR (CMS). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.

ISSUE Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013, U3003 and/or P0606 will be present or stored in the powertrain control module (PCM) memory.

injection (GTDI) engine and built on 9/1/2012 and through 8/1/2013 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2096 (post catalyst fuel trim system too lean bank 1) stored in powertrain control module (PCM) memory. This may be due to engine oil migrating from the variable valve timing (VVT) oil control solenoids through the engine wire harness to the catalyst monitor sensor (CMS).

MAY CAUSE A CONCERN OF A MALFUNCTION INDICATOR LAMP ILLUMINATED , ENGINE MAY NOT START OR MAY RUN ROUGH, LOSS OF POWER , OR LOSS OF ENGINE. *LJ

CONCERN OF A MIL ENGINE RUNNING ROUGH OR LOSS OF POWER. *LJ

*TA

*TA

FULLY SEATED AND SYMPOSER VALVE FLAP NEEDS CHECKING FOR POSSIBLE OBSTRUCTIONS. MODEL 2013-2014 FOCUS ST. *PE

ILLUMINATE, WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2122, P2127 AND/OR 02138. MODEL 2012-2013 FOCUS, 2013 ESCAPE. *PE

MULTIPLE DIAGNOSTIC TROUBLE CODES (DTC) WITH ILLUMINATION OF CHECK ENGINE LIGHT. MODEL 2012-2014 FOCUS. *PE

UNDISTURBED FOR A PERIOD OF TIME. MODEL 2013 FOCUS. *PE

DISTRIBUTION AND FILTERING, FOR ENGINE SOUND SYMPOSER VALVE WIRING. MODELS 2013 FOCUS ST. *PE

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

Automatic Transmission Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Due to ongoing limited part availability, program terms have been revised. Vehicle pickup & delivery has been added. Labor allowance table has been updated. Additional repairs updated. Added Attachment VI Mobile Repair/Vehicle Pickup and Delivery Record. Added Attachment VII Mobile Repair Assessment.

equipped with a DKPS6 Automatic Transmission Transmission Clautch Shudder/Transmission Input Shaft Seal warranty Extension

from the warranty start date of the vehicle, whichever occurs first. This extended warranty coverage will address intermittent symptoms of loss of transmission engagement while driving, no-start, or a lack of power.

warning of electrical circuit failures in the TCM. As communicated in a previous Customer Satisfaction Program (14M02), electrical circuit failures within the TCM may develop and result in intermittent symptoms of loss of transmission engagement while driving, no-start, or a lack of power. Updating the TCM software will help ensure the vehicle operator is alerted to potential issues with the TCM prior to failure.

Automatic Transmission - Transmission Control Module Service Warranty Coverage

Automatic Transmission - Transmission Control Module Extended Warranty Coverage

Automatic Transmission - Transmission Control Module Reprogramming for Overt TCM Failure Warning

Automatic Transmission - Transmission Control Module Extended Warranty Coverage

Transmission Clutch Shudder / Transmission Input Shaft Seal Warranty Extension

This may be due to a high-voltage battery coolant cooler (chiller) leak that may have been caused by prior transmission service. Follow the Service Procedure steps to correct the condition.

of the high voltage (HV) battery pack. In order to correct the condition, perform a programmable module installation (PMI) using the appropriate Ford scan tool. This action will initiate a coordinated flash of powertrain control module (PCM) and transmission control module (TCM) for HV battery compatibility. The use of a previous session may also cause DTC U1030 to be present in the BECM. For additional information refer to 2015 or newer Workshop Manual (WSM), Section 414-03A

AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE EXTENDED WARRANTY COVERAGE

IF REPAIRS ARE NEEDED USE PART NUMBER FU2Z-14S411-VA. REPLACEMENT OF WIRING HARNESS 12A581 IS NO LONGER REQUIRED WHEN THIS CONNECTOR NEEDS SERVICING.

AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE REPROGRAMMING FOR OVERT TCM FAILURE WARNING.

TRANSMISSION CLUTCH SHUDDER / TRANSMISSION INPUT SHAFT SEAL WARRANTY EXTENSION.

TRANSMISSION MAY EXHIBIT EXCESSIVE TRANSMISSION CLUTCH SHUDDER ON LIGHT ACCELERATION. SOME VEHICLES MAY OR MAY NOT EXHIBIT TRANSMISSION FLUID LEAKING FROM THE CLUTCH HOUSING. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

THIS CHANGE AFFECTS TCM/PCM CALIBRATIONS. 2011-2013 FIESTA CALIBRATIONS HAVE NOT YET BEEN RELEASED, CONTINUE TO SERVICE WITH BV6Z-7B546-F CLUTCH, PERFORM ANY REPROGRAMMING WITH IDS RELEASE 101.01 ONLY. 2014-2016 FIESTA VEHICLES CONTINUE TO USE FA6Z-7B546-A CLUTCH AND ARE NOT AFFECTED BY CALIBRATION. 2012-2016 FOCUS CAN USE CLUTCH F1FZ-7B546-B FOLLOWING TSB 15-0120 AND FSA 14M01 AND CALIBRATIONS RELEASED WITH IDS 101.02. WORKSHOP MANUALS HAVE BEEN UPDATED TO INCLUDE A REPAIR VALIDATION CODE (RVC) IN DIAGNOSIS BY SYMPTOM, PINPOINT TEST A (FOCUS, 2014-15 FIESTA), PINPOINT TEST N (2011-2013 FIESTA). RVC CODE IS NOT REQUIRED ON WARRANTY CLAIMS AT THIS TIME. ALL PUBLICATIONS WILL UPDATE SOON, WHEN 2011-2013 FIESTA CALIBRATION IS RELEASED.

AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE EXTENDED WARRANTY COVERAGE

AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE REPROGRAMMING FOR OVERT TCM FAILURE WARNING

INTERMITTENT TRANSMISSION ENGAGEMENT LOSS WHILE DRIVING OR A LACK OF POWER OR NO START AND SOFTWARE NEEDS TO BE REPLACED *CN

POWER *CN

SHUDDER ON LIGHT ACCELERATION ON VEHICLES THAT HAVE A DPS6 AUTOMATIC TRANSMISSION *CN

SEE DOCUMENT SEARCH BUTTON. FORD 2011 THROUGH 2014 FIESTA AND FOCUS VEHICLES: SERVICE BULLETIN REGARDING EXCESSIVE TRANSMISION CLUTCH AND TRANSMISSION LEAK WARRANTY EXTENSION. *LJ UPDATED 10/08/2015 *CN

LIGHT ACCELERATION, CLUTCH SHUDDERING. *LJ

CLEAN THE DPS6 TRANSMISSION BELL HOUSING AND CLUTCH, SHOULD AVOID INPUT SHAFT SEAL EXPOSURE TO SOLVENT. *TA

LEAK TRANSMISSION FLUID FROM CLUTCH HOUSING. MODEL 2011-14 FIESTA, FOCUS. *PE UPDATED 9/25/2015 *CN

P0850, P087A, P087E, P0884, P283A, P2831, P2836, P2837, P2835, AN INTERMITTENT OR DELAYED ENGAGEMENT, AUTOMATIC TRANSMISSION SHIFTING FROM PARK, DRIVE OR REVERSE, NOISE DURING START, INTERMITTENT START, NO CRANK, NO START OR HARD START. MODEL 2012-13 FOCUS. *PE

TRANSMISSION SHUDDER AND MAY OR MAY NOT BE LEAKING TRANSMISSION FLUID FROM CLUTCH HOUSING. MODEL 2011-2014 FIESTA, FOCUS. *PE

MESSAGE CAN BE DISPLAY WITHOUT OVERHEATING OF TRANSMISSION. MODEL 2011-2014 FIESTA, FOCUS.

HEPTANE, EFFECTIVELY, WILL CLEAN FLUID. MODEL 2011-2014 FIESTA, FOCUS. *PE

START AND/OR VARIOUS OTHER TRANSMISSION ISSUES IN DRIVE OR REVERSE, NO ENGAGEMENT WHEN SHIFTING FROM PARK, DELAYED OR INTERMITTENT ENGAGEMENT. MODELS 2012-2013 FOCUS. *PE

WITH MODERATE TO AN AGGRESSIVE ACCELERATION. MODELS 2013 FOCUS. *PE

SHIFTING, MODERATE TO AGGRESSIVE ACCELERATION. MODEL 2013 FOCUS ST. *PE

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

(PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.

(PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.

THE WINDOW STICKER INDICATES 0-19 MILE RANGE FOR 2013-2016 CMAX/FUSION ENERGI. VARIATION OF EV RANGE MAY NOT INDICATE A BATTERY OR CHARGING CONCERN. EV RANGE IS SIMILAR TO THE DTE DISPLAY ON GASOLINE VEHICLES, EV RANGE WILL VARY WITH DRIVING/OPERATING CONDITIONS. CONDITIONS INCLUDE: EXTREME OUTSIDE TEMPERATURES, TERRAIN, DRIVING STYLE, CITY OR HIGHWAY DRIVING, TIRE PRESSURE, AND USE OF ACCESSORIES. IF THE CUSTOMER REPLACES THE LOW ROLL RESISTANCE TIRES WITH A MORE AGGRESSIVE TREAD THE RANGE WILL SUFFER. USING THE CABIN HEATER AND A/C, WHICH ARE ELECTRIC, WILL ALSO DECREASE EV RANGE. TO TEMPORARILY REMOVE THE IMPACT OF DRIVING/CLIMATE HISTORY, RESET THE LIFETIME SUMMARY OR DRIVING HISTORY BY USING THE SETTINGS MENU ON THE LEFT SIDE OF THE INSTRUMENT CLUSTER, UNDER DISPLAY

THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.

TROUBLE CODES (DTC) P06B8, P068A, P2610, IF KEY NOT LEFT FOR 30 SECONDS IN OFF POSITION FOLLOWING PROGRAMMING ON SOME MODEL 2009-15 VEHICLES. *PE

THAT CAUSES THE MALFUNCTION INDICATOR LIGHT (MIL) TO BE ILLUMINATED. MODEL 2013 FOCUS. *PE

AND WITH A START STALL SYMPTOM, WITHIN 20 SECONDS. MODEL 2012-2014 FOCUS, 2013-2014 ESCAPE, C-MAX. *PE

(BCM) AND SHOULD BE IGNORED AND NO REPAIRS OR DIAGNOSTICS PERFORM. MODEL 2012-2014 FOCUS, C-MAX, ESCAPE. *PE

UNDERSIDE OF FRONT PASSENGER SEAT SHORTING TO GROUND. MODEL 2012-2014 FOCUS. *PE

IMPROVED COOLING FAN CIRCUIT DUE TO A LACK OF AIR CONDITIONING, A MALFUNCTIONING INDICATOR LAMP (MIL) AND OVERHEATING. *PE

OF SEVERAL COMPONENTS, IF DIAGNOSTIC TROUBLE CODE (DTC) IS PRESENT. MODEL 2013 C-MAX, 2013-2014 ESCAPE, FOCUS. *PE

P1594 IS SET IN BODY CONTROL MODULE (BCM). MODEL 2012-2014 FOCUS, 2013-2014 ESCAPE, C-MAX. *PE

MODULE ACCELERATOR PEDAL POSITION PERFORMANCE) MALFUNCTION INDICATOR LIGHT (MIL). MODEL 2012-2014 FOCUS. *PE

INTERMITTENT OPERATION OF SEVERAL ELECTRICAL COMPONENTS AND GROUND CIRCUITS NEED TO BE CHECKED. MODEL 2013 C-MAX, 2013-2014 ESCAPE, FOCUS. *PE

MODELS 2012-2013 FOCUS, ESCAPE. *PE

REMOTE START FEATURE, WOULD HAVE CRANK NO START OR STALL, SHORTLY AFTER VEHICLE HAS BEEN DRIVEN. MODELS 2013 C-MAX, FOCUS, ESCAPE. *PE

COMPARTMENT AND INTERIOR LAMPS ARE INOPERABLE, IN SOME VEHICLES. MODELS 2013 FOCUS. *PE

CYCLE, OR SLOW NAVIGATION CALCULATIONS, DUE TO AMOUNT OF DATA, WITHIN SIZE OF CONTACT LIST, CREATING PROCESSING PROBLEM FOR MODULE DURING KEY ON CYCLE. MODELS 2011-2013. NO MODEL LISTED. *PE

FROM FRONT DISPLAY INTERFACE MODULE (FDIM). MODEL 2012-2013 FOCUS. *PE

INTERFACE MODULE (FDIM), TOUCHSCREEN CALIBRATION MUST BE PERFORMED. MODEL YEARS 2011-2013. NO MODELS LISTED. *PE

INFORMATION REGARDING EXTENDED WARRANTY FOR COVERING ACCESSORY PROTOCOL INTERFACE MODULE REGARDLESS OF MILEAGE. MODELS 2011-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, MKZ, F-150, F-SUPER DUTY. *PE

EXPERIENCING COMPACT DISCS GETTING STUCK WHILE ATTEMPTING TO EJECT OUT THE SYSTEM. *TA

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

indicator in the instrument panel cluster (IPC) and the vehicle does not move. The condition may occur when the vehicle is restarted within 20 seconds after being powered off, starting the vehicle within 20 seconds of unplugging or starting the vehicle 15 minutes after being remotely started. Follow the Service Procedure steps to correct the condition.

indicator in the instrument panel cluster (IPC) and the vehicle does not move. The condition may occur when the vehicle is restarted within 20 seconds after being powered off, starting the vehicle within 20 seconds of unplugging or starting the vehicle 15 minutes after being remotely started. Follow the Service Procedure steps to correct the condition.

a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.

THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED. ON 5 DOOR FOCUS(HATCHBACK) THE EXPOSED EDGE AT THE REAR LIFT GATE AREA MAY BE DUE THE HEM LIP OUT OF POSITION (BENT) PULLING THE WEATHER STRIP OUT OF POSITION, EXPOSING THE EDGE. THE HEM LIP CAN EASILY BE REPOSITIONED AND WILL KEEP THE HEADLINER EDGE COVERED BY THE WEATHER-STRIP, WITHOUT HEADLINER REPLACEMENT.

REFER TO WSM, SECTION 303-01 REMOVAL AND INSTALLATION. THE SEALANT APPLICATION LOCATION HAS BEEN REVISED. SPECIAL ATTENTION SHOULD BE USED AT T-JOINT LOCATIONS FOR CLEANLINESS AND SEALANT APPLICATION.

INDICATOR IN THE INSTRUMENT PANEL CLUSTER (IPC) AND THE VEHICLE DOES NOT MOVE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

MODEL 2012-2014 FOCUS, C-MAX, ESCAPE. *PE

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB  SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB  SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

INOPERATIVE, LACK OF OR SLOW RESPONSE TO PHONE AND VOICE BUTTON OPERATION. MODELS 2012-2013 FOCUS, E-SERIES, EDGE, EXPEDITION, FUSION, EXPLORER, F-150, F-250, NAVIGATOR, 2013-2014 FLEX, 2012-2014 FIESTA, MUSTANG, 2013 ESCAPE, C-MAX, TAURUS, 2012 MKZ. *PE

DEFAULTING TO C AND ADDITIONALLY, THE ABILITY TO SWITCH DISPLAY BACK TO F IS DISABLED. MODEL 2013 FOCUS S. *PE

DISPLAY A MESSAGE UPON INITIAL KEY CYCLE. MODEL YEARS 2013-2014. NO MODELS LISTED. *PE

The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420, P1450, P0443, P0452, P0456, P0460 and/or P2196.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

*LJ

MODEL 2012-2014 FOCUS. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

WARNING LAMP OR ILLUMINATION OF WRENCH LAMP WITH MULTIPLE DIAGNOSTIC TROUBLE CODES (DTCS) AND LOW STATE OF CHARGE OF 12 VOLT BATTERY WHEN NOT CONNECTED. MODEL 2012-2014 FOCUS. *PE

P0217 HAS BEEN UPDATED IN WORKSHOP MANUAL (WSM). MODEL 2012-14 FOCUS. *PE

REPROGRAM TO LATEST CALIBRATION. MODEL 2011-2012 FOCUS. *PE

A SOFTWARE UPGRADE IS AVAILABLE FOR CERTAIN VEHICLES. MODELS 2012-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, F-150. *PE UPDATED 5/10/13. *PE UPDATED 9/17/13. *PE

(DTC) B141B and/or B141C

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

exhibit a crunching or creaking type noise from the front suspension on low speed turns and over bumps.

SUSPENSION, LIKE CREAKING OR CRUNCHING TYPE. MODEL 2012-2013 FOCUS, ESCAPE. *PE

THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

CAN BE REPROGRAMMED TO LATEST CALIBRATION SOFTWARE. MODEL 2013 FOCUS. *PE

This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed.

*PE

MODEL 2012-2013 FIESTA, FOCUS. *PE