2020 Ford F-550 TSBs

with 6.7L Diesel Engine Nitrogen Oxide (NOx) Sensor Replacement, If Required After Dealer Evaluation Reference: Emissions Recalls 22E02, 22E04, 23E01, and 25E09

remove the flex plate bolts AL3Z-6379-BA from the parts list as these bolts are in kit LC3Z-6781-A, update the claim quantity of the part number W709771-S440 to 9 pieces (F-650/F750-Engine Replacement), W706447-S437 and W715068-S437 to 4 pieces, W712861-S439 to 8 pieces(F-Super Duty Pickup And Chassis Cab-Engine Replacement) / 8 pieces (F-53 Motorhome/F-59 Stripped Chassis Cab/F-650,F750 Engine Replacement) / W714286-S442 to 4 pieces (F-Super Duty Pickup And Chassis Cab-Camshaft and Tappet Repair / F-Super Duty Pickup And Chassis Cab-Engine Replacement), include LC3Z-6020-A for the Engine replacement lists, include 1 fuel injector seal kit to the Camshaft and Tappet repair lists, include 4 pieces of W520114-S440 to the E Series-Camshaft and Tappet Repair list, and update the engine oil part numbers XO-5W30-Q1SP and CXO-5W30-LSP6. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing ro

quantity of the front support assembly bolt washers, and part number change of the fluid pan from the Parts List. Some of the vehicles listed in the Model statement above may exhibit a harsh reverse to drive engagements with no diagnostic trouble codes (DTC). This may be due to sticking valves in the main control valve body and/or damaged input shaft seals (F9), and the output shaft seals (F10). Additional model information:  Built On Or Before 13-Dec-2021  10R140 Automatic Transmission

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

for Qualified Vehicles

Label Update

fuel system where quick release couplings are utilized, such as the secondary fuel filter. The Workshop Manual (WSM), Section 310-00 > General Procedures > Quick Release Coupling has been updated to include videos and instructions of proper disconnect/connect steps involving the Type 27 quick release couplings.

Reimbursement

Update

for Qualified Vehicles

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * An illuminated powertrain malfunction (wrench) indicator with DTC P07F7 * Loss of 10th gear. The vehicle may also exhibit harsh engagements and poor shift quality. This may be due to the sleeve in the CDF clutch cylinder shifting axially causing hydraulic circuit leaks.

Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM). The vehicle may also exhibit a slight running rough condition at idle. This may be due to incorrect learned values in the PCM from operating the vehicle at altitudes greater than 2500 feet (762 meters) above sea level. This condition does not affect vehicle drivability or durability.

drive and/or reverse on initial start-up. The condition may occur at times after sitting overnight or for a couple of days. This may be due to the transmission fluid draining back from the torque converter. This is a normal characteristic of the 10R140 transmission and has no effect on durability, do not attempt to repair. Advise the customer to allow more time after first engine start-up and before shifting into gear allowing time for the torque converter to refill.

Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

(MIL) with diagnostic trouble code (DTC) U3012 only stored in the powertrain control module (PCM).

(MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) when operating at elevations greater than 2500 feet (762 meters)

(MIL), lack of power, and/or excessive turbo noise during operation, with diagnostic trouble codes (DTC) P003A, P0045, P0046, P0047, P0048, P0234, P0237, P0238, P0299, P132A, P226C, P2263, P2564, P2565, P2598, P259E, and/or P259F stored in the powertrain control module.

the transmission assembly for various reasons.

Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate.

Some 2020-2022 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit harsh reverse to drive engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and if necessary, replace the input shaft seals (F9) and the output shaft seals (F10).

Control Module (PCM) Software Update REASON FOR THIS SUPPLEMENT Software Availability Update: Software is now available to repair 2021-2022 and 2025 Model Year Econoline vehicles. The service action has been updated accordingly. Technical Information: IDS programing information has been added for 2021-2023 Model Year Econoline Vehicles.

23-Sep-2021 may exhibit a thump/whine/knock noise from the midship fuel tank at idle or during key on, engine off (KOEO) after performing TSB 21-2057. The noise may be more pronounced at fuel levels at or below 1/4 tank. This may be due to the fuel pump

Control Module (PCM) Software Update In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2201, P2209, P220E and/or P24FE stored in the powertrain control module (PCM). This may be due to the software in the PCM and the nitrogen oxides (NOx) sensor 11. To correct the condition, follow the Service Procedure to replace the NOx sensor 11 and reprogram the PCM and transmission control module (TCM).

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

The replacement long block may be equipped with an updated upper oil pan. If the oil filter adapter from the original engine does not mate with the new upper oil pan, service parts PC3Z-6881-A (oil filter adapter), W503277-S439 (package of 6 bolts, 4 bolts required), W718564-S450 (stud), W520101-S442 (nut), and PC3Z-14A206-A (starter cable retaining bracket) will be needed to complete the repair.

During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26C (80F) and may increase to 1200 RPM at -40 C (-40F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.

engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.

powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07F7 stored in the powertrain control module (PCM) and a loss of 10th gear. The vehicle may also exhibit harsh engagements and poor shift quality. This may be due to the sleeve in the CDF clutch cylinder shifting axially causing hydraulic circuit leaks. To correct the condition, follow the Service Procedure to replace the CDF clutch cylinder.

the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22F (-30C). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10F (-12C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.

electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure to inspect for water/moisture intrusion into the BJB and replace the BJB and cover if water/moisture intrusion is found.

Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SBP07 (white/red), remove the left side scuff plate from the floor and inspect circuit SBP07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.

(MIL) with diagnostic trouble codes (DTC) P0315, P054F, P054E, P2A00, P2A01, and/or P02ED stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and the transmission control module (TCM).

(MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM, reprogram the transmission control module (TCM), and perform the Reset Minimum Fuel Mass Adaptions All Cylinders.

that is loudest at the front of the engine where the front timing cover meets the oil pan. This may be due to a cracked oil pump drive gear. If the noise originates from the lower front of the engine, remove the accessory drive belt and retest. If the noise is still present, remove the oil pan and rotate the crankshaft 360 degrees to inspect for cracking. If cracked, replace the oil pump drive gear (LC3Z-6306-A).

(MIL) with diagnostic trouble code (DTC) P1674 stored in the transmission control module (TCM). This may be due to a discharged battery and/or low battery state of charge. Before performing normal diagnostics in Workshop Manual (WSM), Section 307-01, charge and test the battery/batteries using the Ford approved battery test equipment listed in the Ford Warranty and Policy Manual. Replace the battery/batteries if directed by the test equipment. Clear DTCs and perform the self test again. If P1674 returns, refer to WSM, Section 307-01 for normal diagnostics. If P1674 does not return, use the Report a Vehicle Concern link at the bottom of OASIS to submit a report that will assist with the engineering investigation.

It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 F (65 C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.

Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the engine will not turn off and/or have various electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure to inspect for water/moisture intrusion into the BJB and replace the BJB and cover if water/moisture intrusion is found.

This may be due to the powertrain control module inhibiting the engagement of the air conditioning compressor clutch with parameter identification (PID) AC_INHIBIT_11 status showing TRUE. If this PID shows TRUE but the ambient air temperature PID reads correctly, this may be due to a disconnected mass air flow sensor with the ignition on, especially after checking the condition of the engine air filter. To correct the condition, clear all diagnostic trouble codes and perform the HVAC or FCIM - Reset the Outside Air Temperature Sensor Learned Values application. If the condition remains, the vehicle needs to be driven for 2-5 minutes over 23 mph (37 km/h). If the condition still remains, refer to Workshop Manual, Section 412-00 for normal diagnostics.

of tire pressure from the valve stem sealing area of the front wheels. This may be due to corrosion of the wheel preventing the valve stem from sealing properly. To correct the condition, follow the Service Procedure to clean the corrosion from the valve stem sealing area of the affected wheel.

(MIL), lack of power, and/or excessive turbo noise during operation, with diagnostic trouble codes (DTC) P003A, P0045, P0046, P0047, P0048, P0234, P0237, P0238, P132A, P2564, P2565, P2598, P259E, and/or P259F stored in the powertrain control module. If Workshop Manual (WSM) diagnostics lead to turbocharger variable vane actuator replacement, service part LC3Z-9G488-B has been released for service. Replacement of the turbocharger assembly is no longer required. When performing the VGT (Variable Geometry Turbo) Valve reset, make sure that engine coolant temperature (ECT) is at least 158 F (70 C).

entry may exhibit a condition where it is difficult to insert the ignition key and/or turn it to the accessory position when removing the ignition lock cylinder per the functional lock cylinder service procedure in Workshop Manual (WSM), Section 501-14. This may be due to debris or contamination in the ignition lock cylinder. If this concern occurs, use a suitable shop vacuum to dislodge or remove debris or contamination by placing the vacuum hose over the lock cylinder, without the key installed, for 30 seconds. Insert the ignition key and reattempt turning it to the accessory position for lock cylinder removal. If the key will not turn to the accessory position, continue with the non-functional lock cylinder removal procedure.

indicator lamp (MIL) with diagnostic trouble code (DTC) P0339 stored in the powertrain control module (PCM) or the vehicle may exhibit a runs rough concern with no DTCs. This may be due the crankshaft position (CKP) sensor. If pinpoint test JD in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual or Workshop Manual (WSM), Section 303-14 leads to CKP sensor replacement, use service part LC3Z-6C315-C. For claiming, use causal part 6C315 and labor operation 12650D57D in the Service Labor Time Standards (SLTS) Manual.

interior courtesy dome lamps that do not turn off after the doors are shut with the ignition on and/or may intermittently turn on while driving. This may be due to voltage limits in the software in the overhead console. To correct the condition, follow the Service Procedure to replace the overhead console.

Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SBP07 (white/red), remove the left side scuff plate from the floor and inspect circuit SBP07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.

Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SPB07 (white/red), remove the left side scuff plate from the floor and inspect circuit SPB07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.

ticking/clicking/tapping noise at idle that is loudest at the front of the engine where the front timing cover meets the oil pan. This may be due to a cracked oil pump drive gear. If the noise originates from the lower front of the engine, remove the accessory drive belt and retest. If the noise is still present, remove the oil pan and rotate the crankshaft 360 degrees to inspect for cracking. If cracked, replace the oil pump drive gear (LC3Z-6306-A).

(MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, allow the engine to idle for at least 6 minutes with engine coolant temperature (ECT) at or above 170F (75C). For pickup vehicles, exhaust gas temperature (EGT12) must also be at or above 475F (245C). For chassis cab vehicles, EGT13 must be at or above 450F (230C). Clear DTCs and retest. PCM replacement is not necessary for this condition.

engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.

The Workshop Manual (WSM), Section 303-03 Engine Cooling > Diagnosis and Testing > Cooling Fan Control, pinpoint test (PPT) AH for 2021-2022 and Powertrain Control/Emissions Diagnosis (PC/ED) Manual PPT AH for 2020 have been updated to improve diagnostics and reduce unnecessary cooling fan clutch replacements.

(MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, allow the engine to idle for at least 6 minutes with the engine at normal operating temperature. Clear DTCs and retest. PCM replacement is not necessary for this condition.

During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26C (80F) and may increase to 1200 RPM at -40 C (-40F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.

thump/whine/knock noise from the fuel tank at idle or during key on, engine off (KOEO) after performing TSB 21-2057. The noise may be more pronounced at fuel levels at or below 1/4 tank. This may be due to the fuel pump. To correct the condition, replace the fuel pump and sender assembly with service part HC3Z-9H307-AR for vehicles with 160/164 inch wheelbase and a midship fuel tank, HC3Z-9H307-AQ for vehicles with 142/148 inch wheelbase and a midship fuel tank, and HC3Z-9H307-AS for vehicles with an aft of axle fuel tank. For claiming, use causal part 9H307 and applicable labor operations in Section 08 of the Service Labor Time Standards (SLTS) Manual.

engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and/or replace the input shaft seals (F9) and the output shaft seals (F10).

(MIL), lack of power, and/or excessive turbo noise during operation, with diagnostic trouble codes (DTC) P003A, P0045, P0046, P0047, P0048, P0234, P0237, P0238, P132A, P2564, P2565, P2598, P259E, and/or P259F stored in the powertrain control module. If Workshop Manual (WSM) diagnostics lead to turbocharger variable vane actuator replacement, service part LC3Z-9G488-A has been released for service. Replacement of the turbocharger assembly is no longer required.

exhibit diagnostic trouble code (DTC) P0000 stored in the powertrain control module (PCM) after an on-demand self test. This DTC is due to a processing error in the PCM as a result of on-demand self testing. P0000 is an invalid DTC that will not illuminate the malfunction indicator lamp (MIL) and no repairs should be performed.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. The vehicle may not shift out of park (P) and/or have continuously illuminated brake lamps with DTCs P0504 and/or C0040. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure steps to inspect for water/moisture intrusion into the BJB and replace the BJB if water/moisture intrusion is found.

runs rough concern with an illuminated malfunction indicator light (MIL) and diagnostic trouble codes (DTCs) P0087 and/or P008A. This may be due to low fuel level or fuel gelling in cold ambient temperatures. If no root cause is determined after normal Powertrain Control/Emissions Diagnosis (PC/ED) pinpoint test MA, recommend that the customer use a different brand of fuel and use Motorcraft PM-23-A Diesel Fuel Anti-Gel and Performance Improver. Inform the customer that bio-diesel blended fuels have a higher occurrence of fuel gelling. Fuel gelling and or low fuel conditions causing a P0087 and/or P008A is not covered under warranty.

indicator lamp (MIL) with diagnostic trouble code (DTC) P0339 stored in the powertrain control module (PCM) or the vehicle may exhibit a runs rough concern with no DTCs. This may be due to a concern with contamination on the crankshaft position (CKP) sensor. If pinpoint test JD in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual leads to CKP sensor replacement, inspect the sensor for contamination and document the results in the warranty claim. Use causal part 6C315 and utilize labor operation 12650D57D in the Service Labor Time Standards (SLTS) Manual.

23-Sep-2021 may exhibit a thump/whine/knock noise from the midship fuel tank at idle or during key on, engine off (KOEO) after performing TSB 21-2057. The noise may be more pronounced at fuel levels at or below 1/4 tank. This may be due to the fuel pump. To correct the condition, replace the fuel pump and sender assembly with service part HC3Z-9H307-AP. For claiming, use causal part 9H307 and applicable labor operations in Section 08 of the Service Labor Time Standards (SLTS) Manual.

electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) Indicator with DTCs C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure steps to inspect for water/moisture intrusion into the BJB and replace the BJB if water/moisture intrusion is found.

(A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.

the engine air cleaner when operating in extremely snowy conditions. Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). A heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA) is now available for use but is not a warrantable item. It is recommended that the service kit be removed at temperatures greater than 50F (10C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.

engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.

Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.

Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive learning drive cycle before attempting internal service. Although this routine was originally developed for low mileage vehicles, it has proven effective for resolving many shift and engagement symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards Manual.

drive and/or reverse on initial start-up. The condition may occur at times after sitting over night or for a couple of days. This may be due to the transmission fluid draining back from the torque converter. This is a normal characteristic of the 10R140 transmission and has no effect on durability, do not attempt to repair. Advise the customer to allow more time after first engine start-up and before shifting into gear allowing time for the torque converter to refill.

It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the appropriate clutches and/or overhaul main control valve body.

It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the appropriate clutches and/or overhaul main control valve body.

(MIL) with various fuel system related diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While performing pinpoint test (PPT) M in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual, the fuel pressure control valve (F_PCV) and/or fuel volume control valve (F_VCV) parameter identifications (PIDs) may not have an option to manually command them with the Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

equipped with a 3.2L engine and 2018-2020 F-150 vehicles equipped with a 3.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF and then reprogram the PCM.

1-Apr-2020 may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07F7 stored in the powertrain control module (PCM) and a loss of 10th gear. The vehicle may also exhibit harsh engagements and poor shift quality. This may be due to the sleeve in the CDF clutch cylinder shifting axially causing hydraulic circuit leaks. To correct the condition, follow the Service Procedure to replace the CDF clutch cylinder.

with automatic engine braking enabled. This may be due to the software in the transmission control module (TCM). To correct the condition, follow the Service Procedure to reprogram the TCM and powertrain control module (PCM).

(MIL) with diagnostic trouble codes (DTC) P0315, P054F and/or P02ED stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.

(A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.

Some 2020-2021 F-Super Duty vehicles equipped with a 6.7L engine built on or before 10-Feb-2021 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300-P0308, P0603, P203B, P208B, P208C, P20EE, P2201, P24C2, P27B4, and/or P27B5 stored in the powertrain control module (PCM). The vehicle may also exhibit a forced idle condition. This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

(MIL) with only diagnostic trouble code (DTC) P0315 stored in the powertrain control module (PCM). If no drivability concerns are present, clear the DTC and retest. If the DTC returns, perform normal diagnostics per the Powertrain Control/Emissions Diagnosis (PC/ED) Manual. If the DTC does not return, inform the customer that Ford is developing a PCM software fix that is expected in late August/early September, 2021. Advise the customer that vehicle durability is not affected by the condition and they can continue to drive the vehicle. Schedule a follow up appointment for repair in late August/early September, 2021. Monitor OASIS for updates.

electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) Indicator with DTCs C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure steps to inspect for water/moisture intrusion into the BJB and replace the BJB if water/moisture intrusion is found.

05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.

reclining seats fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) 202a for head restraints and FMVSS 207 for seating systems. Contact your local Ford dealer to schedule a service date to perform the recall. Refer to the communication from Ford for additional information.

To correct the condition, remove the exhaust and stand the exhaust up with the turbocharger inlet side facing down using a suitable drain pan. Allow the exhaust to drain for at least 24 hours and reinstall. Do not perform a manual exhaust regeneration.

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

The noise may or may not go away while in PARK and/or NEUTRAL. This may be due to the torque converter studs contacting the flexplate inspection cover and/or internal torque converter damper spring contact. To correct the condition, inspect and adjust the flexplate inspection cover (gas engine only) and/or replace the torque converter (gas or diesel engine).

shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F7, P0751, P0756, P0761, P0766, P0771, P2707, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the appropriate clutches and/or overhaul main control valve body.

stem replacement for the front wheels. The parts catalog has been updated to use service part F2GZ-1700-D for the front wheels.

exhibit increased steering effort at initial engine start-up, a Steering Assist Fault message present, and/or an illuminated steering warning indicator with diagnostic trouble code (DTC) U0131 stored in the instrument panel cluster (IPC). This may be due to the software in the power steering control module (PSCM). To correct the condition, follow the Service Procedure to update the software in the PSCM.

illuminated malfunction indicator lamp (MIL) with various fuel system related diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). While performing pinpoint test (PPT) M in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual, the fuel pressure control valve (F_PCV) and/or fuel volume control valve (F_VCV) parameter identifications (PIDs) may not have an option to manually command them with the scan tool. This may be due to the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

thump/whine/knock noise from the fuel tank at idle or during key on, engine off (KOEO). The noise may be more pronounced at fuel levels at or below 1/4 tank. This may be due to the fuel pump strategy in the powertrain control module (PCM) software. To correct the condition, follow the Service Procedure to reprogram the PCM.

illuminated powertrain malfunction indicator (wrench) lamp with only diagnostic trouble code (DTC) P07F6 stored in the transmission control module (TCM). The vehicle may also exhibit harsh engagements, poor shift quality and/or loss of 9th gear as a result of the DTC being set. This may be due to the software in the TCM. To correct the condition, follow the Service Procedure to reprogram the TCM.

Some 2020-2021 F-Super Duty vehicles equipped with a 6.7L engine built on or before 10-Feb-2021 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300-P0308, P054F, P0603, P203B, P208B, P208C, P20EE, P2201, P24C2, P27B4, and/or P27B5 stored in the powertrain control module (PCM). The vehicle may also exhibit a forced idle condition. This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

(MIL) with only diagnostic trouble code (DTC) P0315 stored in the powertrain control module (PCM). If no drivability concerns are present, clear the DTC and retest. If the DTC returns, perform normal diagnostics per the Powertrain Control/Emissions Diagnosis (PC/ED) Manual. If the DTC does not return, inform the customer that Ford is developing a PCM software fix that is expected in June, 2021. Advise the customer that vehicle durability is not affected by the condition and they can continue to drive the vehicle. Schedule a follow up appointment for repair in June, 2021. Monitor OASIS for updates.

runs rough concern with an illuminated malfunction indicator light (MIL) and diagnostic trouble codes (DTCs) P0087 and/or P008A. This may be due to low fuel level or fuel gelling in cold ambient temperatures. If no root cause is determined after normal Powertrain Control/Emissions Diagnosis (PC/ED) pinpoint test MA, recommend that the customer use a different brand of fuel and use Motorcraft PM-23-A Diesel Fuel Anti-Gel and Performance Improver. Inform the customer that bio-diesel blended fuels have a higher occurrence of fuel gelling. Fuel gelling and or low fuel conditions causing a P0087 and/or P008A is not covered under warranty.

the engine air cleaner when operating in extremely snowy conditions. Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). A heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA) is now available for use but is not a warrantable item. It is recommended that the service kit be removed at temperatures greater than 50F (10C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance. The service kit instructions mention that air filter FA-2031 is required, however the heavy snow environment pre-filter service kit can be used with either engine air filter FA-1951, or FA-2031 once it is available.

require disabling or enabling the use of the second alternator. The FDRS scan tool now has an application available to allow for disabling or enabling the use of the second alternator. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. The PCM will have an application called Generator Configuration. Download and run this application to enable or disable the second alternator. Next perform a Battery Monitor System (BMS) Reset. Download and run this reset and clear any DTCs.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U029D, U029E, P22A7 and/or P2209 in the powertrain control module (PCM). This may be due to water intrusion into the oxides of nitrogen (NOx) connectors. To correct the condition, follow the Service Procedure to inspect the NOx sensor module and replace the 14406 wire harness.

and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.

During prolonged idle time, vehicles may experience this high/elevated idle to reduce buildup of unburned hydrocarbons from the SCR system. The powertrain control module (PCM) estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 revolutions per minute (rpms) for ambient temperatures near 26C (80F) and may increase to as high as 1200 rpms at -40 C (-40F). These elevated idle periods can last from 20-40 minutes, depending on ambient temperatures. During power take off (PTO) use and already using idle set point control, the elevated speed is disabled. It is required that the operator monitor the vehicle and adhere to the Exhaust Filter warning messages.

indicator lamp (MIL) with diagnostic trouble code (DTC) P0339 stored in the powertrain control module (PCM) or the vehicle may exhibit a runs rough concern with no DTCs. This may be due to a concern with contamination on the crankshaft position (CKP) sensor. If pinpoint test JD in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual leads to CKP sensor replacement, inspect the sensor for contamination and document the results in the warranty claim. Use causal part 6C315 and utilize labor operation 12650D57D in the Service Labor Time Standards (SLTS) Manual.

shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P0751, P0756, P0761, P0766, P0771, P2707, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break in routine for the appropriate clutch(es) and/or replace the main control valve body.

or scraping noise coming from the bellhousing. The noise may or may not go away while in PARK and/or NEUTRAL. This may be due to the torque converter studs contacting the flexplate inspection cover and/or internal torque converter damper spring contact. To correct the condition, inspect and adjust the flexplate inspection cover (gas engine only) and/or replace the torque converter (gas or diesel engine).

High Pressure Fuel Rail Replacement. In some of the affected vehicles, the vehicle may have been built with a high pressure fuel rail where the internal fuel orifice may become dislodged. If the fuel orifice becomes dislodged, it can travel down and damage the pressure control valve pintle resulting in a Diagnostic Trouble Code (DTC) P0088. Before demonstrating or delivering any new in-stock vehicles involved in this program, dealers are to replace the left hand side high pressure fuel rail using the technical instructions, even if DTC P0088 is not present. This service must be performed on all affected vehicles at no charge to the vehicle owner.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

authorization, inoperative remote features and/or a message stating the system cannot access the Lincoln/FordPass Connect feature in the application due to being a fleet vehicle. Replacing the TCU will not resolve this condition. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0300-P0308, P0603, P203B, P208B, P208C, P2201, P24C2, P27B4, P07F6 and/or P27B5 stored in the powertrain control module (PCM). The vehicle may also exhibit a forced idle condition. This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

lamp (MIL) and diagnostic trouble code (DTC) P20EE. The Powertrain Controls and Emissions Diagnosis (PC/ED) pinpoint test RD15 has been updated to perform a Diesel Particulate Filter (DPF) Manual Regeneration twice along with performing the Specified Function SCR Parameter Reset with the appropriate Ford diagnostic scan tool.

31-Aug-2020 may exhibit an illuminated malfunction indicator light (MIL) with diagnostic trouble code (DTC) P0088. This may be due to the pressure control valve in the left fuel rail. To correct the condition, replace the left fuel rail along with the pressure control valve (PCV). For F-250 through F-550 vehicles refer to Workshop Manual (WSM), Section 303-04B. For F-650/F-750 vehicles refer to WSM, Section 303-04A. For claiming use causal part 9D280 and applicable labor operations in Section 09 of the Service Labor Time Standards (SLTS) Manual.

electrical symptoms including a dead battery, horn stays on and no crank/no start. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure steps to inspect for water/moisture intrusion into the BJB and replace the BJB if water/moisture intrusion is found.

3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the after treatment system. Use of these cleaning tools may void the emissions warranty of the hot end after treatment exhaust system and the attached emissions sensors.

malfunction indicator lamp (MIL) due to low fuel level or low fuel pressure. The most common diagnostic trouble codes (DTCs) associated with a low fuel pressure concern are P0087 and P008A. Prior to performing Powertrain Controls and Emissions Diagnosis (PC/ED) Section diagnostics for a no crank concern, verify the vehicle is not out of fuel or has a low fuel pressure concern. The no crank symptom after a low fuel pressure event is new for the 2020 model year.

lamp (MIL) and diagnostic trouble code (DTC) P20EE. The Powertrain Controls and Emissions Diagnosis (PC/ED) pinpoint test RD15 has been updated to perform a diesel particulate filter (DPF) manual regeneration with the appropriate Ford diagnostic scan tool twice along with performing a diesel particulate filter (DPF) parameter reset and drive cycle.

rough concern with malfunction indicator light (MIL) and diagnostic trouble codes (DTCs) P0087 and/or P008A. This may be due to low fuel level or fuel gelling in cold ambient temperatures. If no root cause is determined after normal PCED diagnostic test MA recommend that customer use a different brand of fuel and Motorcraft PM-23-A Diesel Fuel Anti-Gel and Performance Improver. Inform the customer that Bio Diesel blended fuels have a higher occurrence of fuel gelling. Fuel gelling and or low fuel conditions causing a P0087 and/or P008A is not covered under warranty.

illuminated powertrain malfunction indicator (wrench) lamp with only diagnostic trouble code (DTC) P07F6 stored in the transmission control module (TCM). This DTC may be accompanied by harsh engagements, a poor shift quality feel and/or loss of 9th gear as a result of the DTC being set. If no additional codes or symptoms are present, clear the DTC with the appropriate Ford diagnostic scan tool and schedule a follow-up appointment for service mid-September. Inform the customer that engineering is working to implement a solution and advise the customer that they can continue to drive the vehicle. Once available, contact the customer and confirm a service appointment. Monitor OASIS for updates.

2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.

and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-07. Do not submit a claim for this condition.

and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford FDRS scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-01. Do not submit a claim for this condition.

and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford FDRS scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-07. Do not submit a claim for this condition.

trying to select a point of interest using the push to talk feature on the navigation system. Engineering is currently working on a solution for this condition, which is expected to be available in July. Please monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

automatic transmission may exhibit a delay/bump feel when pulling away from a stop. This may be due to the neutral idle feature that automatically reduces the load on the engine when the vehicle stops, and the gear selector is in DRIVE to reduce fuel consumption and emissions. The transmission automatically resumes operation when the brake is released. The neutral idle feature activates when the transmission is sufficiently warmed, and the vehicle is on level grade. Do not attempt any repairs for this condition. Refer to Owners Manual Transmission Section for more information.

A valve seat that is out of position may cause the illumination of the check engine light and may lead eventually to engine damage and potentially resulting in engine failure.

intermittent buzz noise coming from the transmission while the vehicle is in transport mode. This condition is most noticeable with the vehicle in PARK or NEUTRAL and at elevated idle speeds of 850 to 1250 revolutions per minute (RPM). This condition is a normal characteristic while in transportation mode and will be eliminated once the vehicle is placed into normal mode prior to customer delivery. Do not attempt to repair.

pick up box and tail lamps for flatbed installation. Engineering is working to implement a solution for this condition. Advise the customer that a solution through FDRS is expected to be available 27-Apr-2020. Dealers are asked to follow-up with their customers to schedule a service appointment once the solution becomes available. Monitor OASIS for updates.

A damaged piston oil cooler bracket may allow the piston oil cooler to detach. This can lead to low engine oil pressure and may result in intermittent engine noises and/or illumination of the check engine light due to diagnostic trouble code(s).

2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.

5-Dec-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P27B4 stored in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P203B, P2201 and/or DTC P27B4 stored in the powertrain control module (PCM). The vehicle may also exhibit a forced idle condition. This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

2017-2019 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.

Navigation Some 2020 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the infotainment system stating in Michiganwhen trying to select a point of interest using the push to talk feature on the navigation system. Engineering is currently working on a solution for this condition, which is expected to be available in May. Please monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

Fluid (DEF) Injector Testing Some 2017-2020 F-Super Duty/2018-2020 F-150 vehicles equipped with the 6.7L or 3.0L engines may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P208E in the powertrain control module (PCM). When performing pinpoint test RK, the results of the selective catalyst reductant (SCR) dosing measurement test (RK7) may be zero or below the specified 40-50mL requirement due to urea crystals plugging the DEF injector nozzle. If the measurement is below this specified amount, perform pinpoint test step RK7 two additional times. If the specified amount is met, reinstall the reductant injector. If after three attempts the dosing measurement remains below the specified amount, the DEF injector should be replaced. The DEF pump should not be replaced for DTC P208E.

malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P203B, P2201 and/or DTC P274B stored in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.

may exhibit harsh upshifts between 1st and 5th gears. This may be due to various strategies within the transmission control module (TCM) software. To correct the condition, follow the Service Procedure to reprogram the TCM.

and diagnostic trouble code (DTC) P203B. If performing pinpoint test RJ in the Powertrain Control and Emission Diagnosis (PC/ED) does not identify an issue, do not attempt any repairs at this time. Engineering is currently investigating. Monitor OASIS for updates.

If only the scheduling portion of the remote start system is not functioning, no repair attempts should be made to correct this condition. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from FordPass or Lincolnway application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis. Do not attempt repairs at this time. Engineering is currently investigating, monitor OASIS for updates.

For vehicles with less than 200 miles (320 km) on the odometer, these harsh upshifts may be due to the transmission adaptive strategy not being fully adapted. The harsh upshifts are not detrimental to transmission operation or durability and upshift quality may improve as the vehicle is driven. If the vehicle does not have any illuminated warning indicators or diagnostic troubles codes (DTCs), do not perform any repairs at this time. Engineering is investigating. Monitor OASIS for updates.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Reason for update: To add 2020 model year chassis cab vehicles. Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM. This condition does not affect vehicle drivability or durability.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.

(SCMH) software update using the Ford Diagnosis and Repair System (FDRS) scan tool may set DTCs U024B and/or U024C in the auxiliary protocol interface module (APIM).

toggle button in the Connectivity setting menu grayed out with an inability to switch it off.

the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.

concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software

using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.

using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.

REASON FOR THIS SUPPLEMENT Technical Information: Updated with revised instructions to account for wiring harness changes that were implemented into production and changes to the tailgate latch control assembly removal and installation procedures. As a result, the Labor Allowances and Parts Requirements / Ordering Information have also been updated accordingly. Parts Requirements/Ordering Information: All parts are on open order. Special Service Support Center (SSSC) contact is no longer required to order tailgate actuator ground wiring kit.

To change the vehicle configuration from halogen to LED headlamps, run the BCM-Turn Signal Lamp Configuration application using the latest software level of the Ford Diagnosis and Repair System (FDRS). Vehicles configured to use LED headlamps incorrectly may cause premature halogen bulb failure.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

In all of the affected vehicles, the event data recorder (EDR) was inadvertently disabled. In the event of a crash or near crash-like situation, the event data recorder within the restraint control module (RCM) will not collect and store data used to help understand how the safety systems performed. There is no impact to normal vehicle operation or the vehicles safety systems.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

code (DTC) P0073 for the ambient air temperature sensor stored in the powertrain control (PCM). When performing pinpoint test BF in Workshop Manual (WSM), Section 413-01, the ambient air temperature sensor/outside air temperature display reset procedure has been added to the Ford Diagnostic Repair System (FDRS) diagnostic scan tool. Depending on how the vehicle is equipped, run the FCIM or HVAC. Reset the Outside Air Temperature Sensor Learned Values application. Clear DTCs and retest after performing the reset procedure.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Fault, and/or Collison Warning Not Available message with various diagnostic trouble codes (DTC) stored in the image processing module A (IPMA). If programming fails or Ford Diagnosis and Repair System (FDRS) states a file failed to flash after replacing the IPMA or reprogramming IPMA software, test the battery using any approved Rotunda tool including the GR-190, GRX-3590, and DCA-8000. Fully recharge or replace the battery according to results of the tool. Set the battery charger to maintain battery voltage between 12.6 and 13.6 volts during the entire programming procedure. The IPMA programming procedure may take several hours to complete due to the size of the software files required.

vehicles, the event data recorder (EDR) was inadvertently disabled. In the event of a crash or near crash-like situation, the event data recorder within the restraint control module (RCM) will not collect and store data used to help understand how the safety systems performed. There is no impact to normal vehicle operation or the vehicles safety systems.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

boards (PRB) may exhibit a condition where the PRBs are disabled, changing the feature menu setting from Auto to Off mode in the instrumental panel cluster (IPC), DTC U3003:16 stored in the running board control module (RBM) and with or without an illuminated charging system indicator lamp. This may be due to a low battery voltage event or a fully discharged battery. To correct this condition, inspect the charging system and correct the low battery voltage event. Refer to Workshop Manual (WSM), Section 501-08 > Diagnosis and Testing. Configure the PRB system mode from Off to Auto mode in the Advance Settings of the IPC. Refer to the Owner's Manual > Power Running Boards.

The marketing Order Guide stated that on units equipped with Ambulance & Wrecker packages, customers would get up to 7000 lb front spring FGAWR. The front coil springs were built to match the FGAWR labels on these units. The customer did not receive the front coil spring capability they were expecting based on the data in the marketing Order Guide and their reserve capacity might be lower than expected.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

may exhibit various steering fault messages with diagnostic trouble code (DTC) C1B00 stored in the power steering control module (PSCM). To correct the condition, reprogram the PSCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 3G568 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

may exhibit various steering fault messages with diagnostic trouble code (DTC) C1B00 stored in the power steering control module (PSCM). To correct the condition, reprogram the PSCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 3G568 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

The marketing Order Guide stated that on units equipped with Ambulance & Wrecker packages, customers would get up to 7000 lb front spring FGAWR. The front coil springs were built to match the FGAWR labels on these units. The customer did not receive the front coil spring capability they were expecting based on the data in the marketing Order Guide and their reserve capacity might be lower than expected.

Some 2015-2020 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.

the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

appearing to be randomly touched without user input, slow operation and/or inoperative touch screen operation. To correct the condition, replace the front display interface module (FDIM). For claiming, use causal part 18B955 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.

Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

module (ACM), and/or diagnostic code (DTC) U0184 stored in the SYNC module (APIM) or instrument panel cluster (IPC). If the vehicle is in transport mode, disable transport mode and retest. Refer to Workshop Manual (WSM), Section 419-10. If the concern is still present, perform a radio power reset by removing fuse F32 in the body control module (BCM) for 5 minutes. Reinstall the fuse and retest. If the concern is present, disconnect connector C240A from the ACM, reconnect, and retest. If the vehicle still exhibits the concern, refer to WSM, Section 415-00 and proceed with normal diagnostics.

Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.

some of the affected vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may lead to intermittent front view or Center High Mount Stop Lamp (CHMSL) camera operation. This could result in a blank or distorted image from the front of the vehicle or of the truck bed Dealers are to replace the front view camera or the CHMSL camera following the dealer bulletin technical information. This service must be performed on all affected vehicles at no charge to the vehicle owner.

sides of trailer after performing the FDRS Turn Signal Lamp Configuration application on the vehicle. Version 12 of this application is now available on the FDRS to address this trailer lighting condition. Make sure to download version 12 or later of the FDRS Turn Signal Lamp Configuration and follow the on screen prompts to configure the aftermarket bed. Verify the trailer lighting is operating correctly once complete. If the Turn Signal Lamp Configuration application was previously run on the vehicle, make sure to run the BCM Reset option before re-running the application.

pop-up on the SYNC infotainment system, vehicle connectivity concerns, vehicle location disabled message and/or various FordPass/LincolnWay App command/control concerns. To correct these conditions, ensure that customer connectivity settings (CCS) are turned on in the SYNC system. If the concerns persist after CCS is turned on, turn CCS OFF, perform an ignition cycle, and turn CCS settings back on. After any CCS changes, force-close and relaunch the FordPass/ LincolnWay app on the customers phone. Once CCS is turned on, program the TCU to the latest IDS/FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

pick up box and tail lamps for flatbed installation. To prevent the turn signals from flashing fast, the BCM will need to be configured using the FDRS scan tool. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. The BCM will have an application labeled Turn Signal Lamp Configuration. Download and run this application to configure the turn signals.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

require the removal of the factory equipped tail lamps to accommodate the use of aftermarket equipment. Once the tail lamps are removed, this may result in BLIS and CTA warning indicators illuminated in the instrument panel cluster (IPC). To clear these warning indicators, the BLIS and CTA systems will need to be disabled using the FDRS scan tool. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. The BCM will have an application labeled Disable/Enable Blind Spot Information System. Download and run this application to enable or disable the BLIS And CTA systems.

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

Monitoring System (TPMS) Kits Some 2020 F-Super Duty vehicles were shipped with incorrect FIA trailer camera/TPMS kits and some vehicles ordered with the Trailer TPMS only kit did not ship with the kit. The only accessory trailer kit which can be used on 2020 vehicles is the Trailer Camera only kit HC3J-1A515-CC. Do not attempt to install kits (HC3J-1A515-AC or BC) with trailer TPMS. Vehicles equipped with fifth wheel prep pack and Pro Trailer Backup Assist should install the provided trailer yaw sensor kit 14G551 and plug the yaw sensor wiring into the 12-way bed connector. The trailer camera only kit that shipped with the vehicle can be installed as it connects to the bumper mounted 7/12 trailer connector provided. Follow Super Duty Owners Manual Park Aid section to display trailer Auxiliary Camera view. Trailer TPMS only kit is still unavailable. Monitor OASIS for updates.

App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

service replacement rear glass that uses rear defroster electrical terminals with a plastic overmolded cover. The rear glass defroster terminals are not serviceable and should not be removed or detached from the glass during diagnosis or repairs. If the rear glass defroster terminals are separated from the glass, the rear glass assembly must be replaced.

binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the tailgate step assembly. Before replacing any components for this concern, follow the revised Tailgate Step Adjustment procedure in Workshop Manual (WSM), Section 501-04.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

functional concerns that require replacement after diagnosis. To properly determine if the defect is warrantable, cleaning and close inspection of the affected mirror may be required. To aid in proper warranty determination, the Rear-View Mirror Analysis general service bulletin (GSB) has been updated with a detailed cleaning procedure that should be followed prior to any inspection. New labor operations (17682ZZ or 17682ZZT) have been created that covers the cleaning and inspection process and may be used even if condition of failure is non-warrantable. Ford has inspected numerous returned parts and determined many cases are caused by damage which is unwarrantable and may be subject to chargeback. Refer to the latest version of the GSB on OASIS.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

If there is an issue with the center molding (warped, damaged condition, loose, or if the molding is missing), the trim cover is now available separately. It is no longer necessary to replace the entire rear step assembly (402A48).

This concern may be due to a power door lock actuator. To correct the condition, follow the Service Procedure to replace the affected actuator.

;REASON FOR THIS SUPPLEMENT Technical Information: Updated with revised instructions to account for wire color differences across multiple model year vehicles.

In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford had developed an enhanced remedy for customers who may want this enhanced repair performed n their vehicle.

serviced their vehicle for this concern. Ford has developed an enhanced remedy for customers who may want this enhanced repair performed on their vehicle.

In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford has developed an enhanced remedy for customers who may want this enhanced repair performed on their vehicle.

affected vehicles certain second unit body (SUB) upfits could cause stress points on the frame rail. Over time this stress could cause a crack in the fame rail behind the cab.

binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the step assembly. Before replacing any components for this concern, follow the Tailgate Step Adjustment procedure in Workshop Manual, Section 501-04, General Procedures.

affected vehicles certain second unit body (SUB) upfits could cause stress points on the frame rail. Over time this stress could cause a crack in the frame rail behind the cab.

affected vehicles certain second unit body (SUB) upfits could cause stress points on the frame rail. Over time this stress could cause a crack in the frame rail behind the cab.

opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass panel brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. To correct the condition, follow the Service Procedure to replace the roof opening panel glass brackets

This concern may be due to a power door lock actuator. To correct the condition, follow the Service Procedure steps to replace the affected actuator.

rear door lock is inoperative but the manual lock rod works. This may be due to stack up tolerances of the handle, cable and latch. To correct the condition, follow the Service Procedure to remove the cable barrel sleeve.

washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.

This may be due to dirt and debris on the door check arm(s). To correct this condition, follow the Service Procedure to clean and neutralize the affected door check arms.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the step assembly. Before replacing any components for this concern, follow the Tailgate Step Adjustment procedure in Workshop Manual, Section 501-04, General Procedures.

require the removal of the factory equipped tail lamps to accommodate the use of aftermarket equipment. Once the tail lamps are removed, this may result in BLIS and CTA warning indicators illuminated in the instrument panel cluster (IPC). To clear these warning indicators, the BLIS and CTA systems will need to be disabled using the FDRS scan tool. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. Locate the application labeled Disable/Enable Blind Spot Information System. Download and run this application to enable or disable the BLIS And CTA systems.

configured for operation with the Factory Invoiced Accessory (FIA) or as a Genuine Ford Accessory trailer tire pressure monitoring system (TPMS). The customer may indicate that they cannot monitor the trailer TPMS through the IPC when a configured trailer is connected. If the 'Trailer Tire Pressure' selection is not available in the IPC, the IPC will need to be reconfigured to make the Trailer Tire Pressure selection available. Using the latest version of the FDRS scan tool, reconfigure the IPC. For claiming use causal part 10849 and refer to Section 10 of the Service Labor Time Standards (SLTS) Manual.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.

Reason for update: update the claim quantity of the torque converter nuts, part number and claim quantity of the front support assembly bolt washers, and part number change of the fluid pan from the Parts List. Reissued 01-Oct-2026 - Added LC3Z-7G091-B to the part list

Assembly Reimbursement

Refer to Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing for normal diagnostics. The WSM has been updated with all information from previously published articles related to this concern.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.

(7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.

case may not come equipped with the transmission fluid leveling plug. To achieve proper transmission fluid level, a new transmission fluid pan and gasket must be installed (service part PC3Z-7A194-A). Refer to the 2023 F-Super Duty Workshop Manual, Section 307-01B to properly set the transmission fluid level when using the newer transmission fluid pan.

Ring Gear Assembly Submitting Owner Letter

This may be due to a change to the power tailgate release strategy after the body control module (BCM) has received a software update or the BCM has been replaced. When using the power tailgate release switch in the instrument panel, release switch on the tailgate, or the remote keyless entry (RKE) fob, the power tailgate release switch must be pressed 2 times (2x) within 3 seconds with the transmission in Park for the tailgate to release. If the power tailgate release is still inoperative, refer to Workshop Manual (WSM), Section 501-14 for normal diagnostics.

Ring Gear Assembly: The program has an updated expiration date of March 31, 2023 to encourage dealers and customers to have this service performed as soon as possible. In all of the affected vehicles, a distressed No. 1 planetary needle bearing inside the ring gear assembly will generate contamination that may produce rough shifts. A wrench light is likely to come on, and the transmission may go into safe mode and only operate in seventh gear. As damage progresses, the transmission may only be capable of limited vehicle speed or may not engage in forward or reverse.

upshifting and downshifting strategy. Typical examples are 1-3 or 3-5 upshift or a 6-4 coasting downshift. This is a normal characteristic and no repairs should be attempted for this condition. For more detailed information about the 10R140 skip gear shift strategy refer to the Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing.

noise because the hublocks do not automatically disengage immediately following a shift from 4WD to two-wheel drive (2WD). This may be due to driveline tension between the axle and hub keeping them engaged. To correct the condition, shift the vehicle from DRIVE to REVERSE to release the driveline tension. This is a normal operating characteristic of the vehicle and replacement of the hublocks is not recommended. If the concern remains after shifting into REVERSE and allowing the vehicle to move approximately 5 feet (1.5 meters), remove and inspect the hublocks for any damage. Refer to Workshop Manual (WSM), Section 308-07A. Repair as necessary.

Ring Gear Assembly Parts to repair this condition are now available in sufficient quantities to service all of the affected vehicles. All VINs have been activated. All owner notification through Supplement #2 is complete as of the end of April 2021.

malfunction indicator Lamp (MIL) and/or powertrain malfunction indicator (wrench) lamp with various transmission fluid temperature (TFT) and/or transmission range (TR) sensor diagnostic trouble codes (DTC) P2805, P0706, P0707, P0708, P0709, P2801, P2802, P2803, P2804, P0710, P0711, P0712, P0713 and/or P1711 stored in the powertrain control module (PCM) or the transmission control module (TCM). If any of these DTCs are present, disconnect the transmission vehicle harness connector C168A, and if equipped, the TCM connector C1750 to inspect for damaged or pushed out terminals, corrosion, loose wires and missing/damaged seals. If damage is found, repair as necessary. If no issues are present, refer to Workshop Manual (WSM), Section 307-01 for normal diagnostics.

Ring Gear Assembly Additional vehicles are now eligible for this repair. Vehicles with a 4.30 axle gear ratio, Vehicles with a 4.10 axle gear ratio, Vehicles with a 4.88 axle gear ratio, Emergency vehicles and wrecker vehicles.

Ring Gear Assembly In all of the affected vehicles, a distressed No. 1 planetary needle bearing inside the ring gear assembly will generate contamination that may produce rough shifts. A wrench light is likely to come on, and the transmission may go into safe mode and only operate in seventh gear. As damage progresses, the transmission may only be capable of limited vehicle speed or may not engage in forward or reverse

Ring Gear Assembly- Ref Cust Sat Program 21B03 dated March 3, 2021 In all of the affected vehicles, a distressed No. 1 planetary needle bearing inside the ring gear assembly will generate contamination that may produce rough shifts. A wrench light is likely to come on, and the transmission may go into safe mode and only operate in seventh gear. As damage progresses, the transmission may only be capable of limited vehicle speed or may not engage in forward or reverse

indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator lamp with diagnostic trouble codes (DTCs) P0715, P0716, P0717, P0718, P07BF and/or P07C0 stored in the powertrain control module (PCM). If any of these DTCs are set, focus diagnostics on the turbine shaft speed sensor (TSS) and/or TSS circuits. Refer to Workshop Manual (WSM), Section 307-01. Replacement of the ISSA or ISSB sensor will not correct this condition.

indicator (wrench) lamp with only DTC P07F6 stored in the transmission control module (TCM). The vehicle may also exhibit harsh engagements, poor shift quality and/or loss of 9th gear as a result of the DTC being set. If no additional DTCs or symptoms are present, clear keep alive memory and transmission adaptive tables with the appropriate Ford diagnostic scan tool, and perform an adaptive learning drive cycle. Transmission replacement is not necessary. Inform customers that a further improved calibration will be available in early March 2021. Let the customer know they can continue to drive the vehicle after performing this SSM, and schedule a service appointment for early March 2021. Monitor OASIS for updates.

exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0715, P0716, P0717 and or P07C0 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the turbine shaft speed (TSS) sensor. To correct the condition, follow the Service Procedure to replace the TSS sensor.

indicator lamp (MIL) and/or wrench light with diagnostic trouble codes (DTCs) P0715, P0716, P0717, P0718, P07BF and/or P07C0 stored in the powertrain control module (PCM). If any of these DTCs are set, focus diagnostics on the turbine shaft speed sensor (TSS) and/or TSS circuits. Refer to Workshop Manual (WSM), Section 307-01. Replacement of the ISSA or ISSB sensor will not correct this condition.

Typical examples are 1-3 or 3-5 upshift or a 6-4 coasting downshift. This is a normal characteristic and no repairs should be attempted for this condition. For more detailed information about the 10R140 skip gear shift strategy refer to the Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing.

the IPC message center after the tailgate is closed. This may occur when the key is in the ON position and the tailgate is opened and closed while the vehicle is in a gear other than PARK. Cycling the key or pressing the OK button on the steering wheel will remove the Check Tailgate Ajar message. This is normal operation of the system and no repair attempts should be made to correct a condition. If a customer complaint is received that the Check Tailgate Ajar message does not go away after closing the tailgate, verify and advise the customer of normal operating characteristic.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

affected vehicles, a coding error may have caused a 2.3 display screen instrument panel cluster (IPC) to be installed in place of the 4.2 display screen IPC, as intended with the optional SYNC 3 package. While the display screen size is smaller and appearance differences are noticeable, there is no functional effect on the smaller display screen IPC.

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

interior chime when the vehicle is placed into the reverse position. This chime may come through the vehicles audio system or through the instrument cluster. This may be due to incorrect as-built data in the instrument panel cluster (IPC). To correct the condition, using the latest software level of the appropriate Ford diagnostic scan tool, run the IPC - Instrument Panel Cluster (IPC) Configuration application. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

when using the Ford Pass/Lincoln Way mobile app. Customers may report that the vehicle location that is displayed is the Ford manufacturing facility were the vehicle was assembled, yet all other features work as intended. This may be due to the vehicle location not updating since assembly. If all other Ford Pass/Lincoln Way features work correctly except for the vehicle location, open the customer connectivity settings on the SYNC display and verify that the location setting is enabled. If the setting is currently enabled, disable and then re-enable the feature. If the vehicle location is still displayed incorrectly in the app, follow Workshop Manual section 415-00 for further diagnosis.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure

various concerns such as poor image quality, flickering and/or intermittent blank screen. If a vehicle exhibits any of these conditions replace the high mounted stoplamp camera. Refer to Workshop Manual (WSM), Section 417-01. For claiming, use causal part 19G490 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

chime when the vehicle is placed into the reverse position. This chime may come through the vehicles audio system or through the instrument cluster. This interior chime is characteristic to vehicles that are equipped with a factory exterior backup alarm and no repairs are recommended.

Applications Some 2020 Ford and Lincoln vehicles may exhibit a symptom of no ability to schedule a remote start event using the FordPass or Lincolnway app. If only the scheduling portion of the remote start system is missing from the mobile app or not functioning, please ensure the customer has installed the latest version of the Ford Pass or Lincoln Way app from the mobile phones app store. The customer may also need to log out of the Ford Pass or Lincoln Way app, and then log back in. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from Ford Pass or Lincoln Way application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.

Lincoln vehicles equipped with SYNC 3 may exhibit various performance related concerns such as: intermittent frozen or blank screen, voice prompts with excessive pause between words, remote start not able to be scheduled from Ford Pass or Lincoln Way, Sirius Travel link not working properly, CarPlay not launching on connection or a black screen when connected. To correct this condition, check for SYNC software update on FDRS or Oasis under SYNC the section. If an update is available, refer to WSM section 415-00 to update the APIM software. If the problem persists after programming or no update is available, refer to WSM, Section 415-00 for diagnosis. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

This may be due to the brake pads needing to be broken in. Repeated, heavy brake applications may assist to resolve the pull/drift condition. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information.

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

This may be due to the brake pads needing to be broken in. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

Utilize Workshop Manual (WSM) diagnostics in section 206-00 to verify the correct installation of the stoplamp switch. Improper adjustment of the stoplamp switch can cause the brake pedal assembly to lightly apply the brakes resulting in dragging condition.

Replacement If Required After Dealer Evaluation

Replace Front and/or Side Cameras if Foggy

Replace Front and/or Side Cameras if Foggy

Program will be extended for an additional year; Urgency/Expiration Date: Program will be extended for an additional year Owner Refunds: Refunds have been extended to December 31, 2022, for owner paid repairs completed prior to owner notification date

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Sent with the Ford documents they may receive.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

may exhibit various rear parking aid camera concerns such as poor image quality, flickering and/or completely inoperative. If a vehicle exhibits any of these conditions, replace the rear parking aid camera. Refer to Workshop Manual (WSM), Section 413-13. For claiming, use causal part 19G490 and any applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

This fluid is an improvement in high temperature and thermal oxidative stability compared to Mercon LV. This power steering fluid is also compatible and highly recommended to use when filling or topping off power steering systems of all 2012-2023 F-Super Duty vehicles originally equipped with Mercon LV.

To correct the condition, replace the steering damper with KC3Z-3E651-B and return the vehicle to the customer. For claiming, use causal part 3E651 and applicable labor operations in Section 03 of the Service Labor Time Standards (SLTS) Manual. If the concern returns, refer to the updated procedures, with videos, in Workshop Manual (WSM), Section 211-03 Steering Linkage > Diagnosis and Testing > Symptom Chart.

A new instructional video has been published in the Workshop Manual (WSM) to provide specific measurement instructions on the appropriate tools and methods to determine which steering linkage joints are exceeding lash specifications and which are operating as designed. The left side tie rod end and sector shaft arm drag link joints should not be replaced without obtaining the proper lash measurements. Refer to WSM, Section 211-03 Steering Linkage > Diagnosis and Testing > Symptom Chart.

The workshop manual (WSM) has been updated to provide diagnostic direction for both symptoms, refer to Section 211-03 Steering Linkage > Diagnosis and Testing > Symptom Chart. This message is only to provide awareness of this WSM update and does not supersede other published diagnostic direction.

(MIL) with diagnostic trouble codes (DTCs) P2459, P246C and/or P2463 with a Drive to Clean maintenance message. Vehicles operated primarily in a stationary or off-highway low speed use may exhibit frequent exhaust regeneration attempts. In these conditions, a vehicle may not easily allow for normal exhaust regeneration and may benefit from operator commanded regeneration (OCR) capability so it can perform complete exhaust regeneration in a stationary setting.

a water leak on the right front floor during and/or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct the condensation away from the seal.

or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct condensation away from the seal.

through the doors or air extractors. This may be due to the climate control system being in recirculation mode as a result of the recirculation button being on or automatic strategies for heating/cooling efficiency. To minimize dust ingress when driving in off-road or secondary road conditions, make sure that all doors and windows are fully closed and the climate control system is switched to defrost on and the instrument panel and footwell air vents are switched to off. Temperature and fan settings may be adjusted as desired. Alternatively, max defrost can be activated which will adjust all settings automatically. Operating in defrost mode will keep constant air flow through the rear air extractors and other small areas, helping minimize dust ingress.

Workshop Manual (WSM) diagnostic procedures have been updated to more accurately diagnose A/C performance concerns. Refer to the updated Diagnosis and Testing, and General Procedure in the WSM, Section 412-00 Climate Control System for diagnostic procedures

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SUPPLEMENT Technical Instructions: Updated to clarify amount of use for Rotobroach cutter. Attachment V: Updated list of trucks that will not require bracket installation.

4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet

4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet

This may be due to the air bag cover tear seam design. An updated driver air bag assembly has been released with a more robust air bag cover design. Refer to Workshop Manual (WSM), Section 501-20B for the replacement procedure. If servicing under warranty, use causal part 15043B13 for F-150 and Expedition or 25043B13 for Super Duty and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.