2007 Ford F-450 TSBs

MODEL 2003-2014 F-SUPER DUTY, E SERIES, EXCURSION, F-53 MOTORHOME CHASSIS, LOW CAB FORWARD. *PE

5 VOLTS, DISCONNECT THE ENGINE COOLING FAN CLUTCH, ELECTRONICALLY, AND RECHECK VOLTAGE. MODEL 2003-2007 F SUPER DUTY, 2004-2010 E SERIES, 2003-2005 EXCURSION.

TO LOW INJECTION CONTROL PRESSURE (ICP). *PE

*NJ UPDATED 5/29/08. *NJ

*KB

DIESEL ENGINES. REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST CALIBRATION MIGHT SOLVE THE ISSUE. *KB

*KB

*KB

*KB UPDATED 2/29/08. *NJ

*KB

*KB

*KB

*KB

*KB

VEHICLES EQUIPPED WITH A 6.0L DIESEL ENGINE. *KB

*KB

AND 2004-2008 E-SERIES VEHICLES. *NJ

*NJ

*KB

*KB

*KB

*KB

*KB

MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptable. After 30-Jun-2023, MERCON SP ATF will no longer be manufactured and will only be available until inventory depletes.

*NJ

*NJ

*NJ

4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet

4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet

4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet

4X4 VACUUM HUB SEAL AND OR WHEEL BEARING WEAR AS A RESULT OF HARSH OPERATING CONDITIONS. A KNUCKLE SEAL SHIELD KIT IS NOW AVAILABLE FOR CUSTOMER PURCHASE. THE KIT IS DESIGNED FOR SEVERE DUTY AND IS NON WARRANTABLE. THE KNUCKLE SEAL SHIELD KIT GC3Z-54024A38-A INCLUDES AN INSTRUCTION SHEET.

The customer communication requested return of unsold inventory due to an internal software issue. The internal software issue leads to a false check trailer brake message and Trailer Brake Controller fault whenever the brake pedal is pressed. This will cause the part to be replaced, due to repetitive dashboard warning light, even though it sends signals to the trailer brakes properly.

*RM

*NJ

*KB

IPE

*KB

*KB

*KB

Test results identified that the pull force parameter was not within specification, as a precautionary measure unsold inventory was requested to be returned for testing and containment. We don't have evidence that these test results have contributed to a product failure.

Test results identified that the pull force parameter was not within specification, as a precautionary measure unsold inventory was requested to be returned for testing and containment. We don't have evidence that these test results have contributed to a product failure.

*KB

The programming may fail or vehicle symptoms such as inoperative door locks, dome lamps, door ajar indicators or auto lamps may occur after successful programing. To ensure the VSM is configured correctly, use the Integrated Diagnostic System (IDS) scan tool and select the blue ball and socket icon in the upper left corner. Select the utility knife in the bottom left corner. Select Update/Special Function and enter 53061 in the blue box then press the tick mark. The screen will go back to the system utilities page. Navigate to the toolbox tab and run the Programmable Module Installation (PMI) on the VSM. The procedure will prompt you to manually enter the as-built into the VSM. Obtain the as-built data from PTS > OASIS > As-Built.

*KB

*KB

*KB

VEHICLES EQUIPPED WITH FIXED PEDALS ACCELERATOR PEDAL INSPECTION. EFFECTIVE UNTIL JUNE 30, 2007. *KB THIS PROGRAM IS BEING EXTENDED UNTIL JUNE 30, 2008. UPDATED ON 09/25/07. *NJ