2006 Ford F-150 TSBs

symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis leads to only camshaft/camshaft roller follower(s) requiring replacement, replace all of the camshaft roller followers on both banks/cylinder heads with part number 3L3Z-6564-A, not just the faulty roller follower(s). When replacing the camshaft roller followers, refer to Workshop Manual (WSM), Section 303-01.

Replace all black spark plug boots from the original engine with the 'brown' spark plug boots, as provided. The updated 'brown' spark plug boots are longer than the black boots to accommodate a running change in the spark plug length. The ignition coil bodies and spring/resistor are transferable and only the rubber boots require replacement. Failure to install the spark plug boots provided with the replacement engine could lead to drivability concerns.

2004-2013 F-150, F-250, F-350, EXPEDITION, MARK LT, NAVIGATOR. *PE

FLUCTUATION AND HARD STARTS OR BATTERY DISCONNECT OR DEAD BATTERY AFTER KEEP ALIVE MEMORY (KAM) CLEAR. MODELS 2003-05 THUNDERBIRD, 05-06 MUSTANG, 06-08 FUSION, 04-05 EXPLORER, 05-06 EXPEDITION, 05-07 F-150; 2003-06 LS, 06 ZEPHYR, 05-06 NAVIGATOR; 06-08 MILAN. *PE

IDLE RPM FLUCTUATION AND EXHIBIT DIAGNOSTIC TROUBLE CODES (DTCS) P0505, P0506, P2111 AND P2112. *PE

DECELERATION, DIFFICULTY STARTING, AND/OR IDLE RPM LESS THAN DESIRED. THE F53 MOTORHOME CHASSIS IS INCLUDED. *PE

*NJ

*NJ

COVERED UNDER NEW VEHICLE LIMITED WARRANTY. *NJ THIS INCLUDES F-53 MOTORHOME CHASSIS. UPDATED 2/23/10. *PE

*TT

*TT

*TT

The customer communication requested return of unsold inventory to inspect the dipstick tube. The dipstick tube inner diameter may be small enough that it prevents installation of the OE dipstick.

*KB

*KB

*KB

*TT

*TT

*TT

*TT

*SC

*TT

*TT

Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

The programming may fail or vehicle symptoms such as inoperative door locks, dome lamps, door ajar indicators or auto lamps may occur after successful programing. To ensure the VSM is configured correctly, use the Integrated Diagnostic System (IDS) scan tool and select the blue ball and socket icon in the upper left corner. Select the utility knife in the bottom left corner. Select Update/Special Function and enter 53061 in the blue box then press the tick mark. The screen will go back to the system utilities page. Navigate to the toolbox tab and run the Programmable Module Installation (PMI) on the VSM. The procedure will prompt you to manually enter the as-built into the VSM. Obtain the as-built data from PTS > OASIS > As-Built.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

*RM

NOT ALL F150 ROUSHCHARGED VEHICLES WILL BE AFFECTED BY THESE VARIATIONS. *PE UPDATED 12/16/08. *PE

*NJ

*TT

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

FROM THE GRILLE AREA WHEN TRAVELING AT HIGHWAY SPEEDS OF 65MPH AND GREATER. THIS MAY BE THE RESULT OF A POSSIBLE GAP BETWEEN THE TOP OF THE GRILLE SURROUND TRIM AND THE FRONT EDGE OF THE HOOD. *PE

*TT

grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.

IN THE CASE OF THE ROUSHCHARGER FOR THE F-150, THE TRUCKS CALIBRATION ENHANCEMENTS HAS BEEN DEVELOPED TO BETTER ACCOMMODATE REGIONAL VARIATIONS IN PREMIUM FUEL QUALITY. EVEN THOUGH NOT ALL F-150 ROUSHCHARGED TRUCKS WILL BE AFFECTED BY THESE VARIATIONS. CSC LETTER WAS REC'D. *PE UPDATED 4/12/10. *PE

*NJ

The customer communication requested return of unsold inventory to inspect for the port size being too large. If the port size is too large it will not fit the mating component which would prevent installation, and would therefore have no impact on the end user besides time to complete installation.

*KB

*TT

*NJ

BLLIZZARD SNOWPLOWS. *TT

*TT

*NJ

VEHICLE AFTER IT HAS BEEN PARKED FOR A FEW HOURS. *TT

*TT

*TT

*TT

*TT

*TT

*TT RAPID FEATHERING WEAR OF FRONT TIRES. *TT RAPID SHOULDER (TOE) WEAR ON INSIDE EDGE OF FRONT TIRES. *TT

FRONT HUBS WHEN OPERATING IN TWO-WHEEL DRIVE (2WD) MODE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

*TT