2023 Ford Explorer TSBs

the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.

smoke on startup for the first 5 minutes after an overnight cold soak with no illuminated malfunction indicator lamp (MIL) or powertrain diagnostic trouble codes (DTCs) present. This may be due to engine oil breaching the dynamic oil seals separating the bearing core from the turbine housing in the left side turbocharger assembly. There is a new, updated left side turbocharger oil supply tube equipped with an internal check valve to prevent the engine oil from entering turbine housing after the engine is off. Replace the existing left side turbocharger oil supply tube with the updated service part that includes the check valve (service part# L1MZ-9T516-B) or latest level part. Refer to the Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger > Removal and Installation > Turbocharger Oil Supply Tube LH. For claiming, use causal part 9T516 and labor operation code 9440AL.

Reason For Update: update the Model section to remove Aviator 10R80, update the Parts list to add 3.3L to W520514-S440, and add L1MZ-7Z490-G valve body separator plate for Aviator. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).

Reason for update: update the labor operation numbers to add MT to operations C, F, G, H, J, K, L and M, and correct the part number LIMZ-4A015-B to L1MZ-4A015-B. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as ne

hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.

and 2023 Explorer Vehicles Front Windshield Wiper Motor Replacement, if Required After Dealer Evaluation

Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).

Reason for update: update the labor time allowance for F-150 vehicles, update the Parts list to replace the part number W716979-S439 with W721084-S439, and add a note for LV fluids XT-10-QLVC and CXT-10-LV6 "Transfer Case Fluid". Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other tra

2016-2024 Model Year Explorer, 2019-2020 Model Year Fusion, 2016-2018 Model Year Focus RS, 2022-2024 Model Year Maverick, 2016-2019 Model Year MKC and 2019-2024 Model Year Ranger Vehicles Equipped with a 2.0L or 2.3L Engine and Engine Block Heater System Block Heater Replacement

vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.

Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).

3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.

3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test G located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.

The Workshop Manual (WSM), Section 303-05A Accessory Drive - 2.3L EcoBoost > Removal and Installation > Air Conditioning (A/C) Compressor Belt procedure has been revised to eliminate cutting the A/C compressor belt to remove it. Refer to the updated procedure to reuse the belt.

3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).

vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2021-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2021-2024 F-150 vehicles equipped with a 2.7L EcoBoost, and 2021-2024 Bronco and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F has been updated to include additional steps along with a video to identify the affected VCT unit that requires replacement.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to docum

engine may exhibit may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9 stored in the powertrain control module (PCM). This may be due to a concern with the turbocharger wastegate. To correct the condition, follow the applicable diagnostic pinpoint tests (PPT) steps found in Workshop Manual (WSM), Section 303-04 and repair as necessary.

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

turbocharger oil supply tube due to various concerns.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation.

noise at idle and/or while driving.

vehicles equipped with a 2.7L or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.

Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.

vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation.

harsh/delayed engagements and/or harsh/delayed shifts, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

Some 2021-2023 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation. To correct this condition, replace the fuel injector assemblies (service part L1MZ-9F593-B) for only the respective bank setting the DTC. Refer to Workshop Manual, Section 303-04B. For claiming, use causal part 9F593 and applicable labor standards in Section 10 of the Service Labor Time Standards (SLTS) Manual.

noise from the front suspension at low speeds between 8-20 mph (13-32 km/h) over bumpy or uneven pavement. This may be due a loose pressure tube within the strut assembly. Diagnose and replace the 18124 front strut or struts as needed by which side(s) the noise is isolated to. If noise persists, follow the Workshop Manual (WSM) > Section 204-00 > Diagnosis and Testing > Suspension System > Stop/Steer/Ride > Noise > Front > Over Bump. For claiming, use causal part 18124 and applicable labor operations in Section 3 of the Service Labor Time Standards (SLTS) Manual.

Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

The 2023 F-150 10R80 and 10R80 MHT vehicles will be the subject of a separate article. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

Some 2020-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine or 2020-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L PHEV engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn VCT unit. To correct the condition, follow the Service Procedure to replace the VCT units

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM) and auto start/stop disabled. This may be due to a loose wiring connection to the belt integrated starter generator (BISG). The Workshop Manual (WSM) has recently been updated to provide new direction for DTC P0A1E. Refer to the WSM, Section 303-06 Starting System, Diagnosis and Testing, Starting System for applicable diagnosis.

malfunction (wrench) indicator and/or 4WD Fault Service Required message with diagnostic trouble codes (DTCs) C00A6:71, C00A6:74, C00A6:99, C00A7:11, C00A7:13, C00A8:11, and/or C00A8:13 present in the AWD module. This may be due to a damaged wiring harness rubbing against the underbody heat shield where it routes over and into the transfer case actuator motor. Inspect the wire harness for damage and repair as necessary following the procedures in the Wiring Diagram Manual. If no damage is found, continue with normal diagnostics.

EcoBoost engine, and 2023-2024 Expedition/Navigator vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.

harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy and/or sticking valves in the main control valve body. To correct the condition, follow the Service Procedure to identify and correct the condition.

vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes. stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.

indicator light (MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If there is no coolant flow, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If if there is any coolant flow, return to Workshop Manual (WSM), Section 303-03A diagnostics.

Engine - Engine Long Block Replacement

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.

hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.

non-hybrid vehicles equipped with a 3.0L EcoBoost engine built on or before 01-Jan-2023 may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.

Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

non-hybrid vehicles equipped with a 3.0L EcoBoost engine may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.

Repair

lamp (MIL) and low oil pressure warning in the instrument panel cluster (IPC), with diagnostic trouble codes (DTC) P0521 and/or P0524 in the powertrain control module (PCM). This condition may be caused by an internal oil pressure leak. If pinpoint test E in the Workshop Manual (WSM) Section 303-01B directs you to the replacement of the oil pump, upon reassembly inspect that the main oil gallery tube (6718) is assembled and aligned properly on the back of the engine front cover. The engine oil gallery seal (00815) must be replaced any time the front cover is removed (per WSM Section 303-01B). The WSM front cover removal and installation procedure is in the process of being updated.

(MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If there is no coolant flow, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If if there is any coolant flow, return to Workshop Manual (WSM), Section 303-03A diagnostics.

18-May-2023 may experience a loss of coolant with coolant in the oil. This may be caused by a cracked engine block. If this condition is present, replace the engine long block assembly. Refer to Workshop Manual (WSM), Section 303-01. For claiming use causal part number 6010 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

malfunction (wrench) indicator and stop safely now warning. Diagnostic trouble code (DTC) P0AA6:00 may be stored in the battery energy control module (BECM). Inspect the right side frame rail area near the bank 1 charge air cooler (CAC) intake pipe clamp for chafing the orange high voltage harness. If the harness is damaged, de-energize high voltage system per Workshop Manual (WSM), Section 414-03A. Reposition the clamp and replace the high voltage harness (14290). If the harness is not damaged continue P0AA6 diagnostics in WSM, Section 414-03A, Pinpoint Test T. For a P0AA6 diagnostic aid video, refer to Professional Technician System (PTS) > Home > Technical Assistance > Technical Support Videos > enter P0AA6 in search box and click video returned.

For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.

noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.

2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

(MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If coolant flow is blocked, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If flow is steady, return to Workshop Manual (WSM), Section 303-03A diagnostics.

2022-2023 Police Interceptor Utility (hybrid) vehicles built on or after 17-Aug-2022, 2023 Aviator (gas engine) vehicles built on or after 18-Jul-2022, and 2023 Aviator (hybrid) vehicles built on or after 27-Jul-2022 are not equipped with a rear parking aid camera wash feature. The feature was deleted; however, the rear parking aid camera washer jet may still be present without a hose attached to it. This is normal and no repair attempts should be made.

F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.

vehicles, a damaged tool used during the engine block machining process may have allowed the main oil galley to exceed specification, resulting in an insufficient seal of the main oil galley plug. An insufficient seal at the main oil galley plug may result in an oil leak from the engine block.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.

vehicles, a damaged fixture used during the engine block machining process may have allowed the dimension of one of the head bolt bore holes to exceed specification, reducing head bolt thread engagement.

diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold start in cold (at or below freezing) ambient temperatures. The vehicle may also enter fail safe cooling open loop mode when this concern occurs. If the engine does not show any obvious signs of overheating and Workshop Manual, Section 303-03A diagnostics are inconclusive, clear the DTCs to reset the fail safe cooling open loop mode. Inform the customer that Ford is currently investigating this concern and that they can continue to drive the vehicle. Monitor OASIS for further updates.

Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update

Batteries Battery Energy Control Module (BECM) Software Update

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.

vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

lamp (MIL) with diagnostic trouble code (DTC) P0420 stored in the powertrain control module (PCM). This may be due to the software in the PCM.

2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

with diagnostic trouble code (DTC) P0456 stored in the powertrain control module (PCM). This may be due to evaporative emission system concerns and/or the software level of the PCM and has no effect on vehicle operation.

toggle button in the Connectivity setting menu grayed out with an inability to switch it off.

hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.

powertrain may exhibit diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.

the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.

concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software

using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.

using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.

P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking the fuel pump monitor (VE518) and/or a fuel pump control (VE225) circuits, connector pin push-outs, damaged pins/terminals, and/or loose/corroded grounds. Inspect FPCM connector C433/C4033, ground G407, and inline connections C1147 and C3136 for being fully seated and damage free prior to performing guided diagnostics or replacing any components.

indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P084B stored in the powertrain control module (PCM). This may be due to the software thresholds in the PCM. To correct this condition, perform the Service Procedure below to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS). This TSB is superceded by TSB 24-2082

To verify that the BCMC is at fault prior to replacing, perform the following. First, disconnect the battery then check all BCMC connectors for terminal pushout, pin damage, spread terminals, and corrosion. Refer to Workshop Manual Section 100-00 Wire Terminal Inspection and Replacement. If none found, reconnect the BCMC and battery terminals then recheck functionality. If concern still exists, proceed with BCMC replacement.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. To correct this condition, update the Midtronics xRC-3363 High Voltage Battery Rescue Charger to the latest software level by navigating to the Main Menu > Settings > About (i) then selecting the download button in the bottom right corner of the tool's screen.

(FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections, when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. To correct this condition, update the Midtronics xRC-3363 High Voltage Battery Rescue Charger to the latest software level by navigating to the Main Menu > Settings > About (i) then selecting the download button in the bottom right corner of the tool's screen.

turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the accessory protocol interface module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01.

turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call, or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the SYNC module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

(FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the Technician to verify the low voltage connections, when no actual fault is present. The technician will need to delete the WiFi connection from the xRC-3365 so it will not automatically reconnect and adjust the date. Next go to Settings>Shop Information>Date/Time Settings and change the date prior to May 1, 2023 and stay off the internet so it will not auto correct itself. Press and hold the power button until the tool turns off. Then turn the xRC-3365 back on and attempt the rescue charge.

have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. Switch and/or module replacement will not resolve this condition. Headlamp operation is not affected while the vehicle is ON. A new headlamp switch is currently under development to correct this condition. The customer can continue to drive the vehicle until parts become available. Monitor OASIS for updated repair information.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly. This condition may be caused by loose wiring terminal crimps on connector C2195 at the push button ignition switch. Examine Pin 1 (CPK34/Gn) first, since it is the only pin with the smallest (26 gauge) wire. To correct this condition, repair terminal crimps per Wiring Diagram (WD) Cell 5. If no wiring terminal faults are found, refer to Workshop Manual (WSM) Section 211-05 for normal diagnostics. The push button ignition switch pinpoint tests in the WSM have been updated.

diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The technician will need to manually enter the vehicle charging mode by selecting 2022 model year, then enter the make and model versus entering the VIN.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.

Assembly Reimbursement

20-Sep-2022 and through 05-Mar-2023 may exhibit a brief illumination of the powertrain malfunction (wrench) indicator when the vehicle is shifted into park (P) with diagnostic trouble code (DTC) P0919 and/or P0929 stored in the gear shift module (GSM). This may be due to the GSM software. To correct this condition, reprogram the GSM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 7P155 and labor operations 12651D and 12651D4.

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

delayed engagement/shift concerns. Refer to Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing for normal diagnostics. The WSM has been updated with information from previously published articles related to this concern.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

fluid venting condition.

(7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.

malfunction (wrench) lamp with diagnostic trouble code (DTC) P084B stored in the PCM. The Workshop Manual (WSM) has recently been updated to provide new direction for DTC P084B.

vehicles built on and before 24-Mar-2023, and 2023 Explorer vehicles built on and before 06-Mar-2023 may exhibit a brief illumination of the malfunction indicator lamp (MIL) when the vehicle is shifted into park (P) with diagnostic trouble code (DTC) P0919 and/or P0929 stored in the gear shift module (GSM). This may be due to the GSM software. To correct this condition, update the software in the GSM using the latest software level of the Ford Diagnosis and Repair System (FDRS).

22-Dec-2022 may exhibit a whine noise during coast down from 25 mph (40 km/h). Vehicles built on 6-Feb-2023 and through 1-Mar-2023 may exhibit a whine noise during acceleration in 1st gear. These conditions may be caused by the machining of the No. 4 shell and sun gear. To correct the conditions, follow the Service Procedure to replace No. 4 shell and sun gear.

lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901

This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (LJ6Z-5452118-B) is now available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel > General Procedures > Inspection and Replacement of the Roof Opening Panel Shield Clip.

code B2DAC may exhibit an inoperative passenger front and/or rear window switch. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in one of the passenger window switches. To correct the condition, replace the passenger window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.

code B2DAC may exhibit an inoperative passenger front and/or rear window. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in the window switch. To correct the condition, replace the window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.

may experience the overhead console sunglass bin cannot be locked in a closed position.

If there is an issue with the roof rack side that requires replacement, a lower level service part is now available separately (7855114 and 7855115). It is no longer necessary to replace the entire roof rack assembly.

after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

after 08-Jun-2022 and 2022 Escape/Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

Reason for update: update the Service Procedure to add notes to clarify the customer symptoms, applicability of this TSB, directing technicians to evaluate both front strut mounts, and add Figure 1 to identify the specific area of the strut mount to observe. Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to the front upper strut mount washer movement under steering loads.

Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to front upper strut mount washer movement under steering loads.

from straight ahead to full lock during low speed turning events. This noise may be due to front upper strut mount washer movement under steering loads.

35-80 mph (55-130 km/h) in the steering wheel and/or seat. This may be due to tire flat spotting caused by vehicles being held at the Chicago Assembly Plant awaiting 360-degree camera repairs. Tire flat spotting on these vehicles may be a temporary concern that is resolved, with no repairs required, after the customer drives a minimum of 200 miles (320 km). Refer to Workshop Manual, Section 204-4A if diagnosis or repair is required after the vehicle has been driven this minimal distance.

35-80 mph (55 130 km/h) in the steering wheel and/or seat. This may be due to tire flat spotting caused by vehicles being held at the Chicago Assembly Plant awaiting 360-degree camera repairs. Tire flat spotting on these vehicles may be a temporary concern that is resolved after driving the vehicle a minimum of 200 miles (320 km) with no repair required. Refer to Workshop Manual, Section 204-4A if further diagnosis or repair is required after the vehicle has been driven this minimal distance.

and/or vibration felt through the seat, steering wheel and/or center console at 25-50 mph (40-80 km/h). This may be due to constant velocity (CV) joint instability at dynamic angles close to zero. To correct the condition, follow the Service Procedure to install a driveline shim.

through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.

crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.

Some 2020-2024 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.

Some 2020-2024 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern

This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern. To correct the condition, follow the Service Procedure to install new grounds on the rear knuckle.

The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Individual level III ballistic panel mounting tab service parts are now available: right-hand (78201B68) and left-hand (78201B69). Replacement of the level III ballistic panel assembly is not required for this condition. Level IV ballistic panels do not have removable mounting tabs and still require complete panel replacement. Level III vs level IV ballistic panels can be identified by a large roman numeral label on the panel or by the vehicle window sticker if equipped.

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

double-clicking the VIN on PTS in the upper left corner) are no longer equipped with the 360 degree view camera or reverse brake assist features. Vehicles affected are equipped with only rear functioning cameras. The vehicle is not misbuilt. Do not submit a claim for this condition. Affected vehicles of this change can be verified by entering a vehicle identification number (VIN) on Professional Technician System (PTS) to check for a 360-degree camera credit on the window sticker. Diagnosis and repair for any parking aid concerns on these vehicles should follow Workshop Manual (WSM) Section 413-13B for Rear Parking Aid Camera System only. Do not use the 360 degree view camera or reverse brake assist diagnostics or repair procedures.

Vehicles affected will be equipped with only rear functioning cameras. The vehicle is not miss built. Do not submit a claim for this condition. Affected vehicles of this change can be verified by entering a vehicle identification number (VIN) on Professional Technician Society (PTS) to check for a 360-degree camera credit on the window sticker. Diagnosis and repair for any parking aid concerns on these vehicles should follow Workshop Manual (WSM) Section 413-13B for Rear Parking Aid Camera System only. Do not use the 360 degree view camera or reverse brake assist diagnostics or repair procedures.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.

Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Replacement If Required After Dealer Evaluation

This may be due to the heat stake clips detaching from the cup holder assembly.

ventilation and air conditioning (HVAC) control panel on the rear of the center console. The following Explorer trim levels no longer include the rear HVAC control panel: Base, XLT 200A, XLT 202A without the Sport Appearance Package (sales code: 68M). Customers can adjust the rear climate control system via the front HVAC control panel. Installation of a rear HVAC control panel is not warrantable.

of the IP during tip-in when the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.

the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.

fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manua

fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manual > Seats > Rear Seats > Adjusting the Second Row Rear Seats for further details. If the seats do not easily push forward manually, it maybe due to tension in the seat track due to uneven assembly torque. To correct these conditions, unbolt the second row seat frame from the floor to relax tension. Start the bolts by hand, then tighten in the correct sequence and torque per Workshop Manual (WSM) Section 501-10B.

Tire Replacement

The customer may notice differential fluid pooling below the vehicle or saturating the wheel well liner. This may be due to the differential vent tube not having enough positive incline. To correct the condition, follow the Service Procedure to replace the differential vent tube.

the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. If diagnostics in the Workshop Manual (WSM), Section 501-14 Body > Handles, Locks, Latches and Entry Systems > lead to fuel filler door switch replacement, install a new fuel filler door assembly ordered from depot stock to correct this condition. Suspect parts have been cleared from parts depot inventory.