2017 Ford Explorer TSBs

Customer concern of a vibration or rough idle in D or R Shudder while driving Lack of engine RPM Low performance, lack of acceleration on take off"

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Extended Warranty Coverage Updated Owner Letters: 20N07/20B27 S1

Control Module Reprogram Submitting Owner Letters

Covered by this Program: all open / unrepaired vehicles from 21B05 (Police Interceptor Utility Vehicles) have been added to 21N01 as 21B05 expires August 31, 2022. Owner Notification: Police Interceptor Utility owners who have not completed 21B05 will be mailed a letter describing this change.

Supplement: Program terms will be in effect through August 31, 2023 This program is now eligible for mobile repairs

the vehicle is in drive (D) or reverse (R). The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure to replace the torque converter and specified internal transmission components that may have been damaged.

Repair Order (RO) opening date for field service actions 21S32 or 21S43 provided that the RO opening date occurs on or before July 31, 2023. This is a one time repair. In some of the affected vehicles exposed to a corrosive environment where road salt is used during winter months, the rear toe link ball joint located in the rear knuckle could seize. A seized toe link ball joint could wear out and develop a knocking noise after installation of the updated toe links in the FSAs 21S32 or 21S43

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.

Date: Ending build date for Chicago Assembly built vehicles has been updated

investigation by Ford Motor Company to obtain field parts for testing. Ford is voluntarily conducting this program to replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Detroit (and Toronto) area. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that parts obtained from this program be returned to Ford for this study

Certain States/Provinces Rear Toe Link Ball Joint Inspection This program is a proactive investigation by Ford Motor Company to obtain field data and parts for testing. Ford is voluntarily conducting this program to inspect the toe link ball joint and, if necessary, replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Nashville (and Calgary) area. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that any parts obtained from this program be returned to Ford for this study

Certain States/Provinces; Rear Toe Link Ball Joint Inspection This program is a proactive investigation by Ford Motor Company to obtain field data and parts for testing. Ford is voluntarily conducting this program to inspect the toe link ball joint and, if necessary, replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Nashville, Houston, Miami, Dallas, Atlanta, Phoenix, Winnipeg, and Calgary areas. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that any parts obtained from this program be returned to Ford for this study.

low performance/lack of acceleration during launch, sluggish vehicle operation and shudder while driving

the vehicle is in DRIVE or REVERSE. The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure steps to replace the torque converter and specified internal transmission components that may have been damaged.

low performance / lack of acceleration during launch, sluggish vehicle operation and shudder while driving.

If the torque converter overheats it can lead to adverse NVH, rough idle, and low performance concerns. Ultimately this will require internal transmission repairs to resolve the concern. Ford Motor Company has developed and update to the Powertrain Control Module software that helps protect the transmission torque converter from overheating when exposed to certain driving styles.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive endplay. To resolve the condition, replace the door glass top run, door glass, window regulator, window motor and wiring harness.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe.

This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive endplay. To resolve the condition, replace the door glass top run, door glass, window regulator, window motor and wiring harness.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe. Follow the Service Procedure to correct the condition on vehicles that meet all of the following criteria: *2013-2019 Explorer *3.5L Ti-VCT engine *Illuminated MIL with only DTCs P013A and/or P013C

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.

drive belt, illuminated charging system indicator, and/or damaged alternator pulley. Accessory drive belt DA8Z-8620-G has been released to eliminate this noise and alternator pulley damage. Refer to Workshop Manual (WSM), Section 303-05 for the removal and installation procedure. For claiming, use causal part 8620 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive endplay. To resolve the concern, replace the door glass top run, door glass, window regulator, window motor and wiring harness.

attempting to update the software to version 3.3. Professional Technician Society (PTS) website may show that software version 3.3 is available for 2019 SYNC 3 vehicles. Do not carry out this update as it may lead to a hardware error message. Engineering is investigating, monitor OASIS for updates.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive endplay. To resolve the concern, replace the door glass top run, door glass, window regulator, window motor and wiring harness.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

30-Sep-2016 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0325, P0327, P0330 and/or P0332. This may be caused by a wire chafe condition near the knock sensor connector C109. Follow the Service Procedure steps to correct the condition.

turning the ignition on after a remote start event. To temporarily resolve the concern, the heated seat control switch may be cycled off and then back on. Do not attempt any repairs at this time. Engineering is investigating. To assist with the investigation, use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form. Monitor OASIS for updates.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

from the right side front interior area while the engine is running. If replacing the DC/AC inverter does not resolve the concern, replace the fuel pump control module with part number FU5Z-9D370-B. Inspect the new replacement module and ensure the engineering part number suffix shows "LA" before installing. If the fuel pump control module has an engineering part number suffix "JA", the part should be returned via the normal part return process. For claiming, use causal part 9D370 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. Engineering is investigating, monitor OASIS for updates.

or hesitation condition at approximately 50-60 MPH in 6th gear under light to moderate loads. If there are no DTCs stored in the powertrain control module (PCM), do not attempt further repairs. Advise customers this is a normal characteristic of the vehicle and will not affect durability of the engine or transmission.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

start idle when the customer expects the A/C remain on. The system will return to normal operation after the ignition is turned to the run position. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report to complete the form.

(TiVCT) engine may exhibit an engine vibration and/or the engine mount leaking fluid. A revised engine mount (GB5Z-6038-A) has been released to address this condition. For claiming, use causal part 6038 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.

or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.

the passenger side front interior area while the engine is running. To isolate the noise to the power inverter, remove fuse 56 from the battery junction box with the engine running. Make sure there is nothing plugged into the 110V outlet during the test. If the noise is no longer present with the fuse removed, the noise is isolated to the inverter and no other components should be replaced. Replacement of the inverter may not resolve the noise. Engineering is aware of the concern and is investigating. The noise does not affect the operation of the power inverter. Please submit a Global Concern Report and continue to monitor OASIS for updates.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.

each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.

engine, built on 14-Jun-2017 and through 21-Jun-2017, may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0740 or P0743 stored in powertrain control module (PCM) memory. Prior to replacing any components, check pin 14 in connecter c168 for correct fitment, tension, push out, or any signs of damage. If terminal replacement is necessary, pigtail kit 8U2Z-14S411-ACB can be ordered to obtain the terminal with wire lead. If no concerns are found with C168, follow normal diagnostic routines for the fault codes. For claiming, use causal part 12a581 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

engines may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2195, P2197, P2626, and/or P2629 stored in powertrain control module (PCM) memory. Follow the Service Procedure Steps to correct the condition.

MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Traffic Listing is not loading but all remaining Travel Link features operate properly. SiriusXM Traffic is only available on vehicles equipped with navigation, only in select markets and requires an active subscription to SiriusXM Traffic information. If SiriusXM Traffic will not load attempt the following procedure. Turn the ignition off, open and close the drivers door, wait for 3 minutes, then drive the vehicle outside to obtain a clear view of the sky. SiriusXM Traffic should recover. If SiriusXM Traffic does not recover continue to monitor OASIS for future updates. Engineering is aware of this concern and no component replacement or any software re-flashes should be performed at this time. The SYNC version can be confirmed via OASIS.

3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.

SPEED DROPPING BELOW SPECIFICATION AFTER REPEATED LIGHT PEDAL TIP-IN/TIP-OUT EVENTS AT LOW VEHICLE SPEEDS, SUCH AS IN HEAVY TRAFFIC JAMS OR A PARKING LOT MANEUVERS. REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) TO THE LATEST CALIBRATION USING IDS RELEASE 104.04 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED

DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

ESCAPE/EXPLORER/MKC/FUSION AND MKZ VEHICLES EQUIPPED WITH SYNC 3 MIGHT EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. ENGINEERING IS AWARE OF THIS POSSIBILITY AND IT IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORTATION MODE. IT IS BENEFICIAL TO EXTENDED BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. IF THE VEHICLE SHOULD EXHIBIT A BLANK SCREEN OR OTHER SYNC SYMPTOMS AFTER IT HAS BEEN TAKEN OUT OF TRANSPORT MODE, REFER TO WORKSHOP MANUAL, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

SIRIUSXM TRAFFIC LISTING IS NOT LOADING BUT ALL REMAINING TRAVEL LINK FEATURES OPERATE PROPERLY. SIRIUSXM TRAFFIC IS ONLY AVAILABLE ON VEHICLES EQUIPPED WITH NAVIGATION, ONLY IN SELECT MARKETS AND REQUIRES AN ACTIVE SUBSCRIPTION TO SIRIUSXM TRAFFIC INFORMATION. IF SIRIUSXM TRAFFIC WILL NOT LOAD ATTEMPT THE FOLLOWING PROCEDURE. TURN THE IGNITION OFF, OPEN AND CLOSE THE DRIVERS DOOR, WAIT FOR 3 MINUTES, THEN DRIVE THE VEHICLE OUTSIDE TO OBTAIN A CLEAR VIEW OF THE SKY. SIRIUSXM TRAFFIC SHOULD RECOVER. IF SIRIUSXM TRAFFIC DOES NOT RECOVER CONTINUE TO MONITOR OASIS FOR FUTURE UPDATES. ENGINEERING IS AWARE OF THIS CONCERN AND NO COMPONENT REPLACEMENT OR ANY SOFTWARE RE-FLASHES SHOULD BE PERFORMED AT THIS TIME. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

electrical terminals, if affected, to ten (10) years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to replace the retaining clips and apply adhesive to the roof rail covers.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

ignition on after a remote start event. The seat back heats properly while the lower seat cushion does not. To correct the concern, reprogram the driver seat module (DSM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to apply adhesive to the roof rail covers.

Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

exhibit a crank/no start condition, inoperative trailer tow lighting and/or inoperative power telescoping mirrors. This may be due to a concern within the battery junction box (BJB) relay module. A lower level service part has been released to allow for replacement of just the BJB relay module instead of the BJB harness. F-Super Duty part number HU5Z-14A067-A, Continental part number GU5Z-14A067-C, Explorer part number FU5Z-14A067-A, Police Interceptor Utility part number GU5Z-14A067-B.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

During the installation of certain police accessories by non-Ford vehicle upfitters, wiring connector C134 may have been left disconnected following the removal and installation of the front bumper cover. If this issue is noted, first check C134 before beginning other diagnostic steps. Reconnecting C134 due to improper reassembly by an outside supplier is not a warrantable repair.

after 1 minute during a remote start event when the customer expects the A/C to remain on. To resolve the concern, reprogram the heating, ventilation and air conditioning (HVAC) control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

To program the fobs, start an IDS session and enter the Red Toolbox > Module Programming > Programmable Parameters > Police Mode > Remote Keyfob Learn > Enable. Next, refer to the RKE Transmitter Programming procedure listed in Workshop Manual (WSM), Section 501-14 > General Procedures to program the fobs. If the RKE fobs fail to program, verify that the fobs are the correct part number. If the fobs are correct for the vehicle, then refer to the inoperative key fob diagnostics outlined in WSM, Section 501-14. This procedure and part numbers do not apply to 2015 and previous model year Police Utility vehicles. Blue lift gate button fobs are part No. GB5Z-15K601-C and red panic button fobs are part No. GB5Z-15K601-A.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

DURING THE INSTALLATION OF CERTAIN POLICE ACCESSORIES BY NON-FORD VEHICLE UPFITTERS, WIRING CONNECTOR C134 MAY HAVE BEEN LEFT DISCONNECTED FOLLOWING THE REMOVAL AND INSTALLATION OF THE FRONT BUMPER COVER. IF THIS ISSUE IS NOTED, FIRST CHECK C134 BEFORE BEGINNING OTHER DIAGNOSTIC STEPS. RECONNECTING C134 DUE TO IMPROPER REASSEMBLY BY AN OUTSIDE SUPPLIER IS NOT A WARRANTABLE REPAIR.

affected vehicles, the roof rail covers can become loose, which can lead to a visible gap between the cover and roof rail base assembly, rattling, and potential detachment

3M Universal Adhesive Black Part Number 08223, 3M Static Mixing Nozzles Part Number 08193 This program provides a one-time repair for the roof rail covers and retaining clips to 10 years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first. This is a one-time repair program. Both roof rail covers should be serviced at time of repair. If a vehicle has already exceeded either the time or mileage limits, this extended warranty coverage will last through June 30, 2021. Coverage is automatically transferred to subsequent owners.

cover and roof rail base assembly, rattling, and potential detachment.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

The left 2nd row 60 percent seat cushion cover is a different design from the right 2nd row 40 percent cushion cover and the two are not comparable. The right seat trim wraps under the seat and is closed off while the left side is not closed off and may appear loose. This is normal appearance and no repairs should be performed. If the seat foam is exposed, the foam can be tucked upward and the cushion cover refitted to conceal the foam. The seat cushion cover and/or foam should not be replaced for either condition.

2016-2019 Explorer roof rack cap clips are now available as a separate part. It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part number FB5Z-7851050-A. Ensure roof rails are properly torqued to 55 in/lbs (6.2 Nm) and that power tools are not used for installation as over-torqueing may cause warpage and poor fitment.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.

EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.

Follow the Service Procedure steps to correct the condition.

It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part # FB5Z-7851050-A. The package contains 7 clips.

RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.

may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.

If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

BEZEL ATTACHED TO THE FUEL FILLER PIPE. THE BEZEL WAS REMOVED TO COMPLY WITH FUEL PUMP VAPOR RECOVERY EQUIPMENT REQUIREMENTS AND SHOULD NOT BE CONSIDERED MISSING. THE ADDITION OF THE INFORMATION BEZEL TO UNITS BUILT ON OR AFTER 9-JUN-2016 SHOULD NOT BE DONE.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

This may be caused by a lack of adhesion of the front door upper moulding to the door. To resolve the condition, follow the Service Procedure steps to reapply adhesive tape to the front door upper moulding. Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: * 2011-2019 Explorer * Equipped with factory keyless entry keypad * Left side front door upper moulding is loose

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

fixed brake pedal assembly may exhibit a brake drag concern or residual pressure in the brake system with the brake pedal fully released. This may be due to an interference condition between the brake pedal arm stop lamp switch bracket and the booster push rod clevis pin bracket. Inspect for a touch condition between the brake pedal arm stop lamp switch bracket and the brake booster push rod clevis pin bracket. If a touch condition exists, replace the brake pedal assembly. For claiming, use causal part 2C434 and applicable labor operations in section 2 of the service labor time standards (SLTS) manual.

while driving or when closing the door. It is not necessary to replace the door to correct this issue. Remove any loose portion of the patch and replace with locally obtained mastic patch cut to the appropriate size, such as the 3M 500mm x 500mm sound deadening pad, part number MMM-8840 or equivalent. For claiming, use causal part 24630 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

the RO date of Powertrain Control Module reflash under Customer Satisfaction Program 20B27.

Workshop Manual (WSM), Section 211-02 Power Steering > Diagnosis and Testing has been updated with improved information to aid with accurate noise diagnosis. Replacing the steering gear may not necessarily eliminate the noise concern. Use Chassis Ears on all suspected components to accurately diagnose noise concerns.

Workshop Manual (WSM), Section 211-02 Power Steering > Diagnosis and Testing is in the process of being updated with improved information to aid with accurate noise diagnosis. Replacing the steering gear may not necessarily eliminate the noise concern. Use Chassis Ears on all suspected components to accurately diagnose noise concerns. Monitor OASIS for updates.

The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 'C to 5 'C (23 'F to 41 'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

This may be caused by the seat being moved firmly from the rearward position to the forward position causing the seat track travel restrictor to bend allowing the adjuster bar to become trapped under the travel restrictor. Follow the Service Procedure to correct the condition.

Terms: added 21R01 and 21R02 REASON FOR PROVIDING A NO-COST, ONE-TIME REPAIR: added 21R01 and 21R02 OWNER NOTIFICATION MAILING SCHEDULE: added mailing schedule for 21R01 and 21R02 OASIS ACTIVATION: added 21R01 and 21R02

For customer satisfaction, Hankook is offering pro-rated tire replacement for vehicles with less than 36,000 Miles. This program is managed by Hankook Tire America Corp. and not claimed under Ford new vehicle limited warranty. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2, contact Hankook Technical Service for possible pro-rated tire replacement. Refer to FMCDealer.com Tire Page for details and Hankook contact information.

If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2 contact Hankook Technical Service for possible pro-rated tire replacement. This may not be the result of improper alignment. For Hankook contact information refer to the Tire Warranty information located on FMCDealer.com.

affected vehicles exposed to a highly corrosive environment where road salt is used extensively during winter months, have experienced a seized toe link ball joint resulting in a fracture of the outboard section of the rear suspension toe link.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints (aka bushings) in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 as an assembly only. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 assembly. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

The customer communication requested return of unsold inventory to revise the design similar to the OEM supercession associated with 19V435. We have received no defects associated with the current design.

or missing temperature control switch. The driver and passenger switches are now available separately from the control head. Replacement of the control head assembly is not necessary. The switches are driver and passenger specific and must be installed in the correct location with the red heat indicator facing up. HB5Z-19986-AA - Drivers Side Switch, HB5Z-19986-BA - Passengers Side Switch

Base model vehicles are not equipped with signature lighting and it is not an option. Base level vehicles without the LED lighting surrounding the headlamps are built correctly and should not be modified by installing the signature lamps. Prior to beginning any diagnostics, verify the proper vehicle model/series utilizing OASIS or referring to Workshop Manual Section 100-01.

BASE MODEL VEHICLES ARE NOT EQUIPPED WITH SIGNATURE LIGHTING AND IT IS NOT AN OPTION. BASE LEVEL VEHICLES WITHOUT THE LED LIGHTING SURROUNDING THE HEADLAMPS ARE BUILT CORRECTLY AND SHOULD NOT BE MODIFIED BY INSTALLING THE SIGNATURE LAMPS. PRIOR TO BEGINNING ANY DIAGNOSTICS, VERIFY THE PROPER VEHICLE MODEL/SERIES UTILIZING OASIS OR REFERRING TO WORKSHOP MANUAL SECTION 100-01.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

This may be caused by the seat being moved firmly from the rearward position to the forward position causing the seat track stop bracket to bend allowing the adjuster bar to become trapped under the bracket. The bracket is located on the inner side of the outboard track at the front. Remove the bracket to release the adjuster bar and slide the seat rearward. Bend the bracket back to the correct position and reattach. Refer to Workshop Manual Section 501-10A. Replacement of the seat track is not necessary to correct this condition. Continue to monitor oasis for updates.

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.