2026 Ford Expedition TSBs

diagnostic trouble code (DTC) U211B:43:48 stored in the body control module (BCM) when performing a Self-Test. This DTC sets due to an internal BCM timing issue during the self-test process. This specific code has no customer impact and does not cause any drivability concerns or warning messages. Clearing DTC U211B:43:48, reprogramming the BCM, or replacing the BCM is unlikely to prevent this DTC from setting. This DTC does not trigger a condition covered under warranty. Note: This guidance only applies to U211B with the specific failure byte 43 in status 48. Any other trusted real-time operation network (TRON) DTCs or different failure bytes associated with U211B are still applicable and technicians must follow Workshop Manual (WSM) normal diagnostics for those DTCs.

Reason for update: To add 2027 vehicle models, update the Parts list to change the tape, and revise Step 4 to change the tape and wrap an additional wiring harness. Some of the vehicles listed in the Model Statement above may exhibit a concern where the horn intermittently sounds when turning the steering wheel. This may be due to incorrect routing of a wire harness in the steering wheel, a loose strand of wire protruding from a wire harness and grounding the driver airbag, and/or a concern with one of the driver airbag mounting points.

built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app

at cold temperatures

powering down properly when when the vehicle goes to sleep

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

Vehicles Driver Door Module and Passenger Door Module Software Update

This may be due to incorrect routing of a wire harness in the steering wheel or a concern with one of the driver airbag mounting points.

a front window does not respond to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function. Advise the customers that driver door module (DDM) and passenger door module (PDM) software updates are currently being delivered to vehicles over-the-air (OTA), which are expected to resolve these symptoms. It is important to advise the customer to select the automatic updates option in the settings menu to enable automatic updates and/or approve prompts to download or install updates if automatic updates are purposely disabled. Monitor Professional Technician System (PTS) for additional information.

mirrors may exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours.

going to sleep when the vehicle is turned off

battery in cold weather conditions (below 32F 0C). Once this condition occurs, the battery draw will remain constant every time the ignition is turned off. This may be due to the power fold seat module (PFSM) (also referred to as the seat control module J SCMJ) software keeping the controller area network (CAN) bus awake.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

diagnostic trouble codes (DTCs) P2418:72 and/or P2450 stored in the PCM. This may be due to improperly connected evaporative emission line connections inside the fuel tank.

noise from the front audio speakers that changes with engine RPM. This may be due to a software concern with the active noise cancellation system. Replacement of audio system components will not resolve this condition. Advise customers that engineering is currently investigating and developing a software solution that is expected by the end of Q1 2027.<br/ ><br /> If experienced, customers can temporarily clear the abnormal noise condition by stopping the vehicle in a safe location, placing the transmission in park, then pressing the audio volume control/power button 5 times until the vehicle center screen begins to reboot. The condition should also be temporarily resolved after parking the vehicle with the ignition off, doors locked, and keys moved more than 15 feet away from the vehicle allowing all systems to go to sleep for at least 15 minutes.<br/ ><br /> If a vehicle exhibits this condition, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professi

BYBAL) may exhibit a concern where the instrument panel cluster (IPC) displays "Seat Cannot Lock Do Not Use" for one or both second row seats. This message can appear if the seat control module-J (SCMJ) is offline. If the Ford Diagnostic Repair System (FDRS) shows the SCMJ offline during a network test, determine if a battery disconnect/connect restores SCMJ communication. Refer to Workshop Manual (WSM), Section 414-01. If not, diagnose communication faults referring to WSM, Section 418-00A.<br /><br /> If no communication faults are present but seat cannot lock warnings occur, engineering seeks feedback on latch sensor circuit voltage while the concern is present. Access (but do not disconnect) connectors C3136/C3135 under the affected second row seat(s). Using a multimeter, connect negative lead to body ground. Using a flex probe or similar, back probe terminals 2 and 22 on C3135 and record the voltage. Back probe terminals 8 and 23 on C3136 and record the voltage.

connection or general Bluetooth pairing concerns for both Android and IOS after an APIM software update. This may be due to the APIM software. To temporarily correct the issue:<br /><br /> * For Android Auto related issues: Clear Android Auto app storage in the center display screen. Vehicle Settings > Settings > Apps > Android Auto > Clear Storage. <br /> * For general Bluetooth connectivity issues: Clear Contacts Storage app storage in the center display screen. Vehicle Settings > Apps > Uncheck hide system apps > Contacts Storage > Clear Storage.<br /><br /> If the condition persists, perform a master reset from the center display screen, remove the vehicle from the phone, then re-pair the device.<br /><br /> If the condition continues to persist, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics and repair as necessary outside of this article.<br /><br /> If the condition is resolved, inform customers that engineering is currently working on a permanent solution

BlueCruise feature intermittently/consistently unavailable when BlueCruise is active and when traveling in a "Blue Zone". Speed sign recognition may also be inaccurate. If there are no active relevant diagnostic trouble codes (DTC) present and the issue persists after multiple key cycles and if the BlueCruise System Health Check passes, download and run the "TCU - Reset Telematics Control Unit (TCU) Module" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the condition is resolved, inform customers that this may be a temporary fix and engineering is currently working on a solution expected in Q4 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal 14G229 and labor operations 12651D and 12651D4. If the condition persists after a test drive, refer to Workshop Manual (WSM), Section 419-03B for normal

feature intermittently/consistently unavailable when BlueCruise is active and when traveling in a "Blue Zone". Speed sign recognition may also be inaccurate. If there are no active relevant diagnostic trouble codes (DTC) present and the issue persists after multiple key cycles and if the BlueCruise System Health Check passes, download and run the "TCU - Reset Telematics Control Unit (TCU) Module" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the condition is resolved, inform customers that this may be a temporary fix and engineering is currently working on a solution expected in Q4 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal 14G229 and labor operations 12651D and 12651D4. If the condition persists after a test drive, refer to Workshop Manual (WSM), Section 419-03B for normal diagnosti

a front window does not respond to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function. Inform customers that engineering is aware of this condition and is investigating a service solution which is expected to be available by the end of Q2 2026. Replacement or reprogramming of the DDM and/or PDM and/or any other components is unlikely to resolve this condition. One-touch open and close function may be restored by resetting the anti-pinch feature described in the Digital Owner's Manual > Windows > Window Bounce-Back > Overriding Window Bounce-Back. The symptom may return after a successful reset of the anti-pinch feature. Show the customer where they can find this reset procedure in the Digital Owners Manual (Windows > Window Bounce-Back > Overriding Window Bounce-Back) so that they can have the option to perform the reset procedure on their own should the symptom return while waiting for the service solution to become available.

start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45

the auto-fold mirror operation from the menu located in the instrument panel cluster (IPC) message center. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical buttons are not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected in Q4 2026. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

Engineering is aware of this condition and is investigating a service solution that will enhance the strength of the arm rest support structure and prevent recurring failures. This solution is expected to be available by the end of Q2 2026. If the customer is not willing to wait for the enhanced service solution, replacement of the seat frame is acceptable. Note that service replacement seat frames will have similar performance attributes for the arm rest support structure as the original seat frame that is being replaced. Should the customer choose to wait for the enhanced service solution that includes a strengthened arm rest support, schedule an appointment with the customer when the repair is made available in Q2 2026. Monitor Professional Technician System (PTS) for updates.

full upright position after performing a reset for an obstruction event. This may be due to the software in the power fold seat module (PFSM). This module may also be referenced as the seat control module J (SCMJ). Inform customers that engineering is currently working on a solution for this condition that is expected in Q4 2026. If a vehicle comes in for this condition, instruct the customer that resetting the 3rd row power folding seats a second time will correct the condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> The 3rd row power seat reset is performed with the following relearn procedure:<br /> 1. Start the vehicle and open the liftgate/tailgate.<br /> 2. Remove all items from the 2nd and 3rd row seats including any obstructions that can prevent from folding/unfolding.<br /> 3. Slide the 2nd row seats forward.<br /> 4. Press the center 3rd power fold

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

a front window does not respond to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function. Replacement or reprogramming of the DDM and/or PDM and/or any other components is unlikely to resolve this condition. One-touch open and close function may be restored by resetting the anti-pinch feature described in the Digital Owner's Manual > Windows > Window Bounce-Back > Overriding Window Bounce-Back. The symptom may return after a successful reset of the anti-pinch feature. Show the customer where they can find this reset procedure in the Digital Owners Manual (Windows > Window Bounce-Back > Overriding Window Bounce-Back) so that they can have the option to perform the reset procedure on their own should the symptom return while waiting for the new software to become available. Inform customers that engineering is currently working on a solution for this condition which will be released via a software update delivered over-the-air (OTA) e

activated and the steering wheel is turned to the right, then immediately back to the left (past the center position). The left turn signal will deactivate once the steering wheel returns to center. This may be due to the multifunction switch. Replacing components will not resolve this issue. Inform the customer that Ford is aware of the concern and engineering is currently working on a solution for this condition that is expected to be announced by March 2026. This concern does not affect vehicle durability and the customer can continue to drive the vehicle. Monitor Professional Technician System (PTS) for additional information and schedule a service appointment for the customer once the repair becomes available.

enters a low-power state

where a window does not respond to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function.

lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901

where a window does not respond to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function.

not open or close the power liftgate/tailgate by pressing the button on the key fob. Additionally, these vehicles may exhibit a symptom where the horn does not sound when the key fob lock button is pressed. Expedition XL vehicles equipped as a SSV have the rear liftgate/tailgate power open/close feature omitted from being operated via the key fob. Pressing the key fob liftgate/tailgate button only locks/unlocks the rear cargo area. The power lift feature will power open/close if the button is pressed on the gate within 45 seconds of pressing the key fob. This functionality cannot be modified and no repairs should be attempted. The Workshop Manual (WSM) has been updated. Refer to WSM, Section 501-03 > Description and Operation > Body Closures  System Operation and Component Description and scroll to the section titled Power Liftgate - SSV (Special Service Vehicle) Operation. The Digital Owner's Manual is in process of being updated.

displayed options are active and relevant."

when the easy entry/exit setting for "Approach Detection" is toggled on. This is a change from prior models. Currently, easy entry/exit settings in the vehicle's center display screen incorrectly indicates that power running boards will deploy during approach detection in auto mode. This will be corrected in a future Digital Experience over-the-air (OTA) update which will begin deploying in mid Q3, 2026. The Workshop Manual (WSM) and Owner's Manual have been corrected to explain proper operation of power running boards.

Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.

code HKCGA) may experience a blank/white Google map screen, inoperative live traffic data, inoperative voice assistant, the inability to sign into a Google account in the center touch screen, unable to access the Google Play Store in the center display screen, and/or the inability to connect to other apps in the center display screen. This may be due to the vehicles Ford Connectivity Package not being activated. To verify if the vehicle has an active Connectivity Package (free or paid) enter the vehicle identification number (VIN) in Professional Technician System (PTS) then navigate to the upper blue tab titled Connected Vehicle > Vehicle Software Subscriptions. It will clearly state if the vehicle has a trial or paid subscription, along with the expiration date. These vehicles will come with one of two connectivity options from the factory.<br /><br /> *A free Connectivity Package trial that lasts for 1-year (identified as minor feature code N01AB). A credit card is required to enable

instrument panel cluster (IPC) and/or an illuminated anti-lock brake system (ABS) indicator with diagnostic trouble code (DTC) C0563 stored in the ABS module. This may be due to air still trapped in the system after prior bleeding attempts and/or brake service mode being enabled. The applicable pinpoint test (PPT) in Workshop Manual (WSM), Section 206-09 has been updated to improve diagnostics for this concern. Make sure the latest software version of Ford Diagnosis and Repair System (FDRS) is being used when performing the brake system pressure bleeding routine.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Navigation System (minor feature code HKCGA) may experience a blank screen for Google Maps or the absence of live traffic data. To correct this condition, refer to the Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Information and Entertainment System. The WSM has been updated with improved diagnostics for this condition. To confirm whether a vehicle is built with a specific minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner of the Professional Technician System (PTS).

hard stops

2025-2026 Expedition/Navigator vehicles built on or before 26-Mar-2026 may exhibit a clicking or creaking type noise when turning the steering wheel during low-speed maneuvers. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). If a vehicle exhibits this condition, use a chassis ears tool and place the microphone clamp on or near the universal joint yoke of the steering column upper shaft (below the column). Turn the steering wheel with the vehicle stationary to replicate the concern. If the same noise is clearly heard through the chassis ears at this location, replace the steering column upper shaft (base part number 3E751). Refer to Workshop Manual (WSM), Section 211-04. For claiming, use causal part 3E751 and service labor operations 3676AUP and 1006D.

activated and the steering wheel is turned to the right, then immediately back to the left (past the center position). The left turn signal will deactivate once the steering wheel returns to center. This may be due to the steering column multifunction switch.

warnings

Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.

Accelerator Pedal Inspection and Replacement