2023 Ford Escape TSBs

statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).

of AP (Actual Programming) Time. Some of the vehicles listed in the Model statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).

Some of the vehicles listed in the Model statement above may exhibit a "Pre-Collision Assist Not Available" message in the IPC and at least one of the following conditions:  Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required"  Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules  Ford Diagnosis and Repair System (FDRS) scan tool cannot establish connectivity with the image processing module A (IPMA) during a self-test. This may be due to the software installed in the IPMA. *** MODEL SECTION ****  2023-2026 Escape equipped with minor feature code: DBCAB or DBCAA  2023-2026 Corsair equipped with minor feature code: DBCBC

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

rust, scratches, curb strikes, road debris, or other minor damage. Section 414-03A of the Workshop Manual (WSM) has recently been updated to improve diagnostics for such damage and provides a list of low-level serviceable components for instances where replacement of the high voltage battery assembly is not warranted. Refer to WSM, Section 414-03A High Voltage Battery, Mounting and Cables > Diagnosis and Testing > High Voltage Battery Minor Damage Inspection. The Ford New Vehicle Limited Warranty covers manufacturing defects resulting from a defect in factory supplied materials or workmanship. Please refer to the Warranty section WHAT IS NOT COVERED, which includes curb strikes and accidents.

Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).

lamp (MIL) with diagnostic trouble code (DTC) P27B2 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software in the SOBDMC.

control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.

screen may experience a rear view camera image in the vehicle's center display screen that is missing the active guidelines overlay and zoom button icon, while in reverse. This may be due to the software in the body control module (BCM). To correct the condition, download and run the "BCM - Body Control Module (BCM) Software Update" application in the Ford Diagnosis and Repair System (FDRS). After the BCM software has been updated, download and run the "Local Interconnect Network (LIN) New Module Initialization" application.

with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.

caused the Image Processing Module A being offline

driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required" - "Pre-collision Assist Not Available"  Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules  Ford Diagnosis and Repair System (FDRS) scan tool can not establish connectivity with the image processing module A (IPMA) during a self test. This may be due to the software installed in the IPMA. *** MODEL SECTION ****  2023-2025 Escape equipped with minor feature code: DBCAB  2023-2025 Corsair equipped with minor feature code DBCBC

and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC. Additionally, some modules may store invalid data/lost communication related DTCs. The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment"

2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

lamp (MIL) with diagnostic trouble code (DTC) P144B stored in the powertrain control module (PCM) without driving performance concerns. This may be due to the PCM software.

Service Procedures from M-time to AP-time. Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).

trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.

system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).

trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.

application using the latest version of the Ford Diagnostic and Repair System (FDRS) scan tool.

-Reduces TCU based Key Off Load battery drain. - Map orientation improvement - removes false"IP Configuration Failure" message when wrong WiFi password is entered. - Improves functionality of Stolen Vehicle Services

strategy that also follows the IPC strategy.

accessory protocol interface module (APIM) software updates have been performed.

with a message displayed in the Ford Diagnosis and Repair System (FDRS) scan tool indicating "Procedure Unsuccessful-Call Get Restore Invalid Hardware: RJ6T-14H107-BBB".

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

strategy - Improved SYNC stabilty. - Provides enhanced security when accessing external content"

intermittent no audio condition with diagnostic trouble code (DTC) U0238 stored in the audio control module (ACM) and/or in the accessory protocol interface module (APIM).

(PHEV) powertrain may exhibit an intermittent 12V battery drain condition when the ignition is tuned off. This may be due to the heating, ventilation and air conditioning (HVAC) control module that keeps the controller network (CAN) bus active.

- Addresses Accessory Protocol Interface Module (SYNC) displaying update status as not completed. - Addresses potential vehicle no start condition post OTA update.

-Minor quality fixes in Enhanced Central Gateway module (ECG) Software, not affecting vehicle operation. - Addresses potential vehicle no start after OTA update.

message center with loss of AWD function for the remainder of the active key cycle. DTCs C0095, C05D9:74, P060A, P060B, P060C, and/or P1674 may be stored in the AWD module. This condition may be due to the software in the AWD module.

hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.

- Gas DTE (Distance To Empty) indication appears continuously when scrolling through all Info on Demand screens. - HMI animation refinements - Eliminates single gauge flicker in ignition off. - Enlarged graphics displayed for ""keep hands on steering wheel"" message.

accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.

Quality Improvements include: - SYNC screen will update after changing to next track from USB device. - Improves minor occurrence of gauge flicker once in ignition "off". - Enlarges graphic for "keep hands on steering wheel" message - Robustness fixes for error handling, menu browsing, navigation and audio repeaters.

an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.

instrumental panel cluster (IPC) with diagnostic trouble codes (DTCs) C1001:78 and U2107:68 stored in the image processing module-A (IPMA) when the vehicle is driven on uneven roads. This may be due to the software installed in the IPMA. To correct this condition, reprogram the IPMA using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool and perform the appropriate IPMA alignment procedure. Perform a self test and clear DTC codes. For claiming, use causal part 14G647 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

where the speed limit sign indicator is not displayed in the HUD. This may be due to the software installed in the HUD module.

screen only displaying imperial (feet and miles) units and not being able to change to metric (meters and kilometers) units. This may be due to the software level of the SYNC module (APIM). To correct this condition, follow the Service Procedure to update the APIM to the latest software level via a coordinated flash. NOTE: The APIM software update that addresses the symptom listed in this article may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.

built on 30-Jan-2023 and through 6-Jun-2023 may exhibit an illuminated air bag warning indicator with DTC B0082:1A stored in the restraints control module (RCM). This may be due to an issue with the passenger seatbelt retractor at connector C303B. If a connection issue is found, replace the passenger front seatbelt retractor and pretensioner assembly before attempting a wiring repair. This issue does not affect the proper operation of the air bags, retractor and pretensioner. Refer to the Workshop Manual (WSM), Section 501-20A Seatbelt Systems > Removal and Installation. For claiming, use causal part 78611B08 and applicable labor times in Section 12 of the Service Labor Time Standards (SLTS) Manual.

side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

when using the power liftgate control switches. The vehicle may exhibit diagnostic trouble codes B1454 and/or B1455. Prior to following Workshop Manual (WSM) diagnostic procedures, remove the liftgate left/right/center upper trim panels. Refer to WSM, Section 501-05 Interior Trim and Ornamentation > Removal and Installation. Disconnect C4173 and C4172 and verify the resistance of the anti-pinch switches. Refer to the Wiring Diagram, cell 109. If the resistance is below 5.58K ohms, replace the affected switch(s). If both anti-pinch switches measure above specification, perform a power liftgate initialization and re-evaluate the concern. Refer to WSM, Section 501-03 Body Closures > General Procedures.

and through 30-Dec-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0230 stored in the powertrain control module (PCM). The vehicle may also experience a no start or stall after start. This may be due to an internal PCM issue. If this DTC is present, verify the battery condition, then perform pin point test (PPT) KC of the Work Shop Manual (WSM), Section 310-01. If PPT KC leads to component replacement, start with replacing the PCM and then evaluate the vehicle. If the DTC returns, follow WSM, Section 310-01 PPT KC direction to address the issue.

(FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the Technician to verify the low voltage connections, when no actual fault is present. The technician will need to delete the WiFi connection from the xRC-3365 so it will not automatically reconnect and adjust the date. Next go to Settings>Shop Information>Date/Time Settings and change the date prior to May 1, 2023 and stay off the internet so it will not auto correct itself. Press and hold the power button until the tool turns off. Then turn the xRC-3365 back on and attempt the rescue charge.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The technician will need to manually enter the vehicle charging mode by selecting 2022 model year, then enter the make and model versus entering the VIN.

with diagnostic trouble code (DTC) P04CA stored in the powertrain control module (PCM). This may be due to an open circuit on circuit SBB05 and/or a damaged splice S133. Before performing the pinpoint test for P04CA in Workshop Manual (WSM), Section 310-00, inspect circuit SBB05 and splice S133 for damage such as an open circuit. Repair as necessary. Refer to Wiring Diagram, Cell 005. If no damage is found, refer to WSM, Section 310-00 for normal diagnostics. For claiming use causal 14290 and labor operations 12650D, 12650D45, and 12650D45WR.

Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20C (-4F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern.

Equipped with an Engine Block Heater System Block Heater Element Installation

message displayed in the instrument panel cluster (IPC) along with other various driver assistance feature warning messages and various invalid data/lost communication diagnostic trouble codes (DTCs) stored in various modules after Technical Service Bulletin (TSB) 25-2249 has been performed. The reoccurrence of these symptoms is related to a different root cause. This condition does not affect vehicle durability, and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in late October 2025. Replacement of the image processing module A (IPMA) will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20C (-4F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers

Diagnostic Trouble Codes triggered by a random engine misfire in the first thousand revolutions of vehicle start

Coolant Over-Temperature" warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20C (-4F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position

2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.

This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

This concern may occur after initial engine start up following an overnight cold soak.

neutral without pressing the brake pedal -Reduces potential no start events due to ABS after OTA update. -If the vehicle shuts off with Auto Vehicle Hold on, itll wake up with AVH on. -Addresses erroneous "Service Park Brake Limited Function" message at start up. - A Check Engine Light may appear after the update, causing no effect on the vehicle. This clears after a few drive cycles.

exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color, this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly.

a 2.3L EcoBoost engine, 2024-2025 Nautilus, and 2025 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM).

malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0496 stored in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.

engagement after auto start/stop feature restarts the engine. This may be due to the software installed in the anti-lock brake (ABS) module. To correct this condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part number 2C219 and the applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.

a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If all spark plugs are found to be free of damage, replacement of the spark plugs is not necessary. Refer to the Workshop Manual and perform normal diagnostics. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics.

Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and a software solution for this condition is expected by the 2nd quarter of 2024. Monitor OASIS for additional information and schedule a service appointments for customers once the repair becomes available.

(R) in cold weather and/or high humidity. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the 4th quarter of 2024. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

It is not necessary to discard the 17 valve cover bolts during disassembly; these bolts can be reused up to 3 times. The Workshop Manual (WSM), Section 303-01A, is scheduled to be updated by the end of June 2024.

a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Adding Not OTA Capable Owner letters. Other documents submitted 01/02/24 & Received OTA letters submitted on 02/01/24

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

display may exhibit a roundabout/traffic circle arrow directing the traffic to go to the left (clockwise) around the roundabout. This is incorrect and opposite to what is displayed in the center display screen. The direction of travel should be to the right (counterclockwise) around the roundabout/traffic circle. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in April 2024. Replacement/reprogramming of the IPC will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20C (-4F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone

Some 2023 Escape/Corsair vehicles equipped with a 2.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) This may be due to the software in the powertrain control module (PCM).

with various lost communication diagnostic trouble codes (DTCs) stored in various modules and multiple illuminated warning indicators such as: anti-lock brake system (ABS) warning indicator, parking brake (red) indicator, brake warning indicator, parking brake (yellow) warning indicator and/or parking brake (red) indicator and/or stability-traction control indicator displayed in the instrumental panel cluster (IPC). This may be due to the software in the ABS module. To restart the vehicle, allow the vehicle to be powered off for more than 10 minutes and attempt a restart. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in February 2024. Replacement or reprogramming of the ABS module will not resolve this condition. Monitor OASIS for additional information

displayed in the instrumental panel cluster (IPC) and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q1 of 2024. Replacement of the cylinder head temperature (CHT) sensor may not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

Coolant Return Tube to Cylinder Head

pre-heater fault, exhaust system fault, change air filter soon, air suspension fault, clean the exhaust filter, check fuel inlet, engine temperature high, anti-theft system/key fault, collision assist unavailable or instrumental panel cluster (IPC). Fordpass may also display a high voltage battery charge of 50% after a full charge.

roundabout/traffic circle arrow directing the traffic to go to the left (clockwise) around the roundabout. This is incorrect and opposite to what is displayed in the center display screen. The direction of travel should be to the right (counter clockwise) around the roundabout/traffic circle. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in January 2024. Replacement/reprogramming of the IPC will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

the dealership to reduce the risk of driving performance issues such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to different fuel specifications between manufacturing plant and final market. Make sure that the vehicles in stock have local fuel added.

pre-heater fault, exhaust system fault, change air filter soon, air suspension fault, clean the exhaust filter, check fuel inlet, engine temperature high, anti-theft system/key fault, collision assist unavailable or instrumental panel cluster (IPC) and Fordpass displayed a high voltage battery charge of 50% after a full charge. Inform customers that engineering is currently working on a solution for this condition and it will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected by the end of October 2023. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. Schedule a service visit for customers who have disabled vehicle connectivity. Monitor OASIS for additional information.

roundabout/traffic circle arrow directing the traffic to go to the left (or clockwise) around the roundabout. This is incorrect and opposite to what is displayed in the center display screen. The direction of travel should be to the right (or counter clockwise) around the roundabout. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in October 2023. Replacement/reprogramming of the IPC will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and/or P0316. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.

2.5L engine, built on 01-Sep-2022 and through 06-Apr-2023, may exhibit a low coolant level with engine oil in the coolant and/or coolant in the engine oil. This may be caused by an internal oil cooler leak. To correct this condition, follow the Service Procedure to test and replace the oil cooler.

and/or boom noise while driving in gears 5-8 at approximately 1500 engine revolutions per minute (RPM). This may be felt more when the engine is under a light to moderate load. A vibration and/or boom noise could be generated from the firing frequency of the 3 cylinders or when cylinder deactivation occurs and the engine is running on 2 cylinders. This condition is more noticeable when the vehicle is driven in ECO mode. This mode was designed to deliver maximum fuel efficiency and increase the driving range.

connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in August 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.

screen only displaying imperial units and not being able to change to metric. This may be due to the software level of the SYNC module (APIM). This issue does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that engineering is currently working on a solution for this condition and will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected in September 2023. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update in September 2023. Monitor OASIS for additional information.

connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.

One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.

looseness/sagging or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (5452118) is available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel for inspection and replacement of the roof opening panel shield clip.

Check-Arm Reinforcement Spot Welds REF: Customer Satisfaction Program 23B56 - Supplement #1 Published December 18, 2024 New! REASON FOR THIS SUPPLEMENT RENTAL VEHICLES: Link to CRC Dealer Portal Job Aid added. CLAIMS PREPARATION AND SUBMISSION: Sublet claiming updated. LABOR ALLOWANCES: Explanation of labor operations that will close the Field Service Action (FSA). PROGRAM TERMS This program will be in effect through May 31, 2027. There is no mileage limit for this program.

code B2DAC may exhibit an inoperative passenger front and/or rear window switch. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in one of the passenger window switches. To correct the condition, replace the passenger window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.

affected vehicles, the front door check-arm reinforcement welds can crack and may eventually pull away from the door structure. If not repaired, the check-arm reinforcement may eventually detach from the door structure. This can cause a rattling noise and increased door opening/closing efforts. It may also interfere with door glass operation and the ability of the check arm to hold the door in the open position . Submitting Owner reminder letters

code B2DAC may exhibit an inoperative passenger front and/or rear window. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in the window switch. To correct the condition, replace the window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.

locking of the driver door after the door is closed. This may be due to the driver placing their hand on the interior front door handle and inadvertently pushing the manual door lock toggle into the lock position. If the lock and latching mechanisms are functioning normally, and if there are no related diagnostic trouble codes (DTCs) or other issues identified, then the system is operating as designed.

driver door after the door is closed.

where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64.

Quality Improvements include: - Liftgate opens fully open with exterior button press

Check-Arm Reinforcement Broken Spot Welds

after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.

Verify the hood/liftgate are not open. Confirm all doors are fully closed and latches are fully engaged. Doors will not fully close when lightly letting go of the door or letting it swing closed from a short distance under its own weight. Push/pull effort must be applied to doors while closing to fully engage latch and turn off the ajar signal warning. If doors are still not fully latching closed, manually adjust door striker position to allow for proper alignment and engagement to the door latch. The door hang position may also need to be slightly adjusted to achieve the same effect. Refer to Workshop Manual (WSM), Section 501-03.

door(s) do not open using the exterior door handle(s). This may be due to an enabled permanent engagement inertia lock within the exterior door handle, this condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the Service Procedure to properly disengage the permanent engagement inertia lock clip to allow the exterior door handle(s) to fully extend and open the door(s) from the exterior.

For 2020-2023 Escape/Corsair vehicles, the roof opening panel frame mechanism kits have been released for service. These components can now be serviced separately and no longer require replacement of the entire roof opening panel frame. To correct the condition, follow the Service Procedure to install the roof opening panel frame mechanism kit.

Assembly Reimbursement

Some of the vehicles listed in the Model statement above may exhibit at least one of the following:  Illuminated malfunction indicator lamp (MIL)  Diagnostic trouble code (DTC) P0767, P0766 and/or P2703 stored in the powertrain control module (PCM).  Harsh reverse or intermittent no reverse engagement. This may be due to an internal mechanical concern with the selectable one-way clutch (SOWC).

on or before 22-May-2025<br /> * 2024 Maverick vehicles built on or after 17-Jan-2024<br /> <br /> Some of the above vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct the condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and labor operation numbers 7001D and 7001D4.

release when shifting to reverse -Customers will receive alerts if the park brake gets stuck in the release maneuver, or if a shift to neutral occurs with driver off brakes

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present Note: Three (3) new Essential Special Service Tools (ESSTs) are required to service the internal clutch pack on vehicles equipped with a single active torque rear drive unit (RDU) only. These ESSTs are expected to ship to all dealers (US, Canada, Puerto Rico and Mexico) in September 2025. ESST packages were shipped to 100 selected dealers in the US and Canada in May 2025, based on RDU part sales activity. The RDU Internal Clutch Kit and Adhesive Sealant are currently under restricted ordering to ensure ample supply of parts are available to dealers with the ESSTs. All parts are expected to be available for open order by Q4 2025, when the ESSTs are planned to arrive at all dealers. Note: For dealers with the ESSTs and a vehicle in the service department that requires a repair using the new RDU Internal Clutch

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

neutral without pressing the brake pedal - Reduces potential no start events due to ABS after OTA update. -if the vehicle shuts off with Auto Vehicle Hold on, itll wake up with AVH on. -Addresses erroneous ""Service Park Brake Limited Function"" message at start up."

the PCM and/or intermittent or constant no reverse engagement.

may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.

may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

(wrench) indicator with DTC P07E6 stored in the inverter system controller SOBDMC, the GSM will display a flashing P on the dial, the P on the instrument cluster is not illuminated, and the vehicle will be stuck in the park (P) position.

noise during acceleration from a stop, or in some cases during the end of a stop event. This may be due to the front half shaft sticking to the wheel bearing surface. To correct this condition, perform the Service Procedure below to lubricate the halfshaft and wheel bearing hub assembly mating surface.

Quality Improvements include: - Reduced no start events. - Quicker brake release when customer shifts to R - Remembers Auto Vehicle Hold status thru key cycle - Warning lamp for park brake stuck event. - Message when shift to neutral occurs with driver off brakes. - Will no longer set erroneous "Service Park Brake Limited Function" during initialization.

transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01.

- Resolves black screen issue caused when there is no SiriusXM disk space."

and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC.

Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC"

This may be due to the software installed in the IPC.

roundabout/traffic circle arrow directing the traffic to go to the left (or clockwise) around the roundabout.

or minor feature code DBCBC for Corsair may exhibit various driver assistance feature warning messages displayed in the IPC.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

Quality Improvements include: - Removal of BlueCruise map expiration - Allow Vehicle entry during OTA. - Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. -Addresses SYNC reboot issue may occur after 2 hours of continuous use.

Quality Improvments include: - Various Apple Carplay quality improvements

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Some of the vehicles listed in the Model statement above may exhibit one of the following conditions: * Multiple illuminated warning indicators displayed in the instrumental panel cluster (IPC): - Anti-lock brake system (ABS) warning indicator - Parking brake (red) indicator - Brake warning indicator - Parking brake (yellow) warning indicator - Parking brake (red) indicator - Stability-traction control indicator * Intermittent no crank/no start condition * Various lost communication diagnostic trouble codes (DTCs) stored in various modules. This may be due to the software installed in the ABS module.

(R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct the condition, follow the Service Procedure to install brake pads with clips and if necessary, install the rear reinforced caliper bushings.

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

with various lost communication diagnostic trouble codes (DTCs) stored in various modules and multiple illuminated warning indicators such as: anti-lock brake system (ABS) warning indicator, parking brake (red) indicator, brake warning indicator, parking brake (yellow) warning indicator and/or parking brake (red) indicator and/or stability-traction control indicator displayed in the instrumental panel cluster (IPC). To correct this condition, follow the Service Procedure to reprogram various modules starting with the PCM.

(R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct this condition, follow the Service Procedure to replace the standard and reinforced rear caliper bushings and apply Kluberpaste to the machined surfaces of the brake caliper and caliper support bracket.

squeal and/or grinding noise and/or vibration from the front brakes while braking. This may be due to excessive wheel hub lateral runout. To correct this condition, remove the front brake disc(s) of the affected wheel(s). Refer to the Workshop Manual (WSM), Section, 206-03. Clean the raised ring-like surface of the front wheel hub near the wheel studs. Using a dial indicator, slowly rotate the wheel hub and measure the runout on the ring-like surface. If the total runout exceeds 0.001 inch (0.03mm), replace the wheel hub. Refer to the WSM, Section 204-01. Document the measured run out in the warranty claim. For claiming use the causal part number 1104 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS)

door keypad code menu item being shown in vehicle settings menu of the center display screen. This may be due to the configuration of the SYNC module (APIM). To correct this condition, download and run the APIM - SYNC Module Configuration application in the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G670 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.

above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.

articles, update labor times associated with the Service Procedure from M-time to AP-time and add a cap.

Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity.

- Improves connectivity - 23 MY Eliminates a post OTA uneccessary message ""Stop Safely Now"" at startup. Clears at next key cycle.

Maverick Vehicles Drivers Side Seat Buckle Replacement

(R) in cold weather and/or high humidity.

Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.

Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.

Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.

Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.

Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.

Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel voice control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interaction capability can be identified as also being equipped with the built in connected navigation feature which includes a navigation tab on the center display screen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.

vehicle's lane while the lane keeping assist is active. The lane keeping aid assists the driver by providing steering torque to help the driver keep the vehicle in the lane when it detects unintentional drifting toward the outside of the lane. Additionally, adaptive cruise control with lane centering provides constant steering torque to keep the vehicle centered in the lane while cruise control is engaged. These are operating characteristics of the lane keeping systems. Refer to the Owner's Manual for complete description of the operation of these systems. Do not attempt diagnosis or repairs or submit a claim for this condition. Inform the customer that the lane keeping system is only an aid, and their hands should stay on the steering wheel at all times while driving.

This may be due to the normal operation of the rear air extractors. To determine if this is a normal condition, perform a road test at 40 mph (65 km/h) or above. Inspect if the noise is coming from the rear extractors. During the road test alternate air conditioning (A/C) between fresh mode and air re-circulation mode. If the noise is eliminated when the A/C is in fresh mode, this is considered a normal characteristic of the vehicle and no repairs should be performed.

with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use base (4000) causal part.