2017 Ford Escape TSBs

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.

08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.

Programming - Some of the affected vehicles may exhibit collant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the short block.

coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.

In some of the affected vehicles the 1.5L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or may run in a rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into a cylinder bore.

Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.

08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.

coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.

08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.

pulley removal, or a drive belt component failure. The crankshaft pulley to be slightly out of alignment in relation to engine top dead center (TDC) causing an incorrect crankshaft position (CKP) sensor signal. To determine this as the cause of the rolling idle, position the crankshaft at TDC using essential special service tool (ESST) 303-748 then remove the CKP Sensor and attempt to install ESST 303-1550. If the bolt to hold 303-1550 cannot be installed by hand, this indicates that the crank pulley is not properly installed. Using a new crank bolt, install the pulley/vibration damper in its proper alignment following the WSM procedure in 303-01. Use ESST 303-393A to hold the flexplate/crankshaft when torqueing down the crank bolt.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). The vehicle may also exhibit an all-wheel drive (AWD) fault warning and/or illuminated traction control (TC) lamp. Inspect the 12A690 (1.5L) or 12C508 (2.0L) wiring harness from the battery junction box (BJB) to the PCM for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 12A690 (1.5L) or 12C508 (2.0L) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.

clunk from the rear drive unit (RDU) when turning at low speeds and parking lot maneuvers. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.

alignment pins between the engine and transaxle. When either a new long block or new short block is installed in the vehicle and the dowel pins were found missing or damaged upon disassembly of the original engine, the flexplate (6375) must be replaced. For engine overhauls or other engine related repairs where the engine and transaxle do not require separation, replacing the flexplate is not required. This direction also applies to existing service publication repairs where the engine and transaxle are separated as part of the repair procedure. Refer to Workshop Manual (WSM), Section 303-01.

08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.

Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition my damage the engine, requiring replacement of the engine short block.

Engine - Powertrain Control Module Reprograming

Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.

coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). This may be due to the crankcase pressure sensor/tube assembly. To correct the condition, follow the Service Procedure steps to replace the crankcase pressure sensor/tube assembly and reprogram the PCM.

diagnostic trouble code (DTC) P051B stored in the powertrain control module (PCM). This may be due to the crankcase pressure sensor/tube assembly. To correct the condition, follow the Service Procedure steps to replace the crankcase pressure sensor/tube assembly.

06-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.

Follow Cooling System Pressure Test process in WSM, Section 303-03. Pressurize system to 138kPa(20 psi) and hold 5 hours. If system pressure drops 27.57kPa(4psi) after 5 hours and borescope inspection through spark plug holes shows coolant presence in bores, the short block must be replaced. Further teardown inspection is not required, nor is completing cost cap. Cost cap requirements are waived for repairs completed utilizing this SSM. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A for repair procedure and refer the parts catalog as needed. Any backorders experienced will be filled as quickly as possible.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Follow Cooling System Pressure Test procedure in WSM, Section 303-03, and pressurize system to 138kPa(20 psi) and hold for 5 hours. If system pressure drops 27.57kPa (4psi) after 5 hours and borescope inspection through spark plug holes confirms coolant intrusion into the cylinders, short block replacement is required. Further teardown inspection is not required. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A procedures for repairs and refer the parts catalog as needed. Short block availability may be limited and temporary backorders will be filled as quickly as possible.

coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. Before completing the Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint test (PPT) follow the Service Procedure steps on vehicle.

and MKC vehicles may exhibit a concern of the license plate bracket nut(s) being damaged due to the screw(s) being over torqued. The torque specification for these screws are 1.7 Nm (1.25 lb-ft). Engineering recommends not to use any power tool to tighten these screws. Most any power tool will apply more torque to the screws than the allowed torque specification and will damage the plastic nut(s).

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Follow the Cooling System Pressure Test procedure in WSM, Section 303-03, pressurize the cooling system to 138kPa(20 psi0 and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the engine block surface to head gasket interface is required. Carefully inspect engine block cylinders and cylinder bore bridges for erosion, pitting, and flatness. If defects with the cylinder block surface are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair. Ford has found that all returned cylinder heads pass inspection and may have been reused.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

idle while the vehicle is in transport mode. The noise is noticeable because of an elevated idle speed while the vehicle is in transport mode. Do not disable transport mode to diagnose or perform a repair for this noise. Transport mode should only be disabled as directed by the pre-delivery procedure.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM to the latest calibration using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Follow the Cooling System Pressure Test procedure in Workshop Manual(WSM), Section 303-03, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect cylinder block for erosion, pitting, and flatness. Defects will be between the engine block cylinders and cylinder bore bridges. If defects with the surface of the cylinder block and/or cylinder head are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair.

diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). The vehicle may also exhibit an all-wheel drive (AWD) fault warning and/or traction control (TC) light on. Inspect the 12A690 (1.5L) or 12C508 (2.0L) wiring harness from the battery junction box (BJB) to the PCM for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 12A690 (1.5L) or 12C508 (2.0L) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) manual.

exhibit inoperative remote features via FordPass Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 110.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). May also exhibit an all-wheel drive (AWD) fault warning and/or traction control (TC) light on. Inspect the 14290 wiring harness at the battery junction box (BJB) under the air cleaner and/or the brake vacuum pump for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 14290 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures

illuminated MIL with diagnostic trouble codes (DTCs) P04DB and/or P051B stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

illuminated MIL with diagnostic trouble codes (DTCs) P04DB and/or P051B stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM using the appropriate Ford scan tool or equivalent release 110.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

illuminated MIL with diagnostic trouble code (DTC) P051B stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

Some 2017 Escape vehicles equipped with an auto start/stop system and built on or before 18-May-2016 may exhibit DTC P1935 stored in the powertrain control module (PCM) on vehicles equipped with a 1.5L/2.0L engine and/or DTC P061E stored in the PCM on vehicles equipped with a 2.0L engine. Follow the Service Procedure steps to correct the condition.

illuminated MIL (wrench) lamp with diagnostic trouble code (DTC) P061E stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

The concern can occur at a stop where the vehicle will perform an auto stop/start event. Upon attempting to restart, the instrument panel may display a message instructing the customer to shift the vehicle to park and start the vehicle manually. This concern may be intermittent and difficult to duplicate. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

The concern can occur at a stop where the vehicle will perform an auto stop/start event. Upon attempting to restart, the instrument panel may display a message instructing the customer to shift the vehicle to park and start the vehicle manually. This concern may be intermittent and difficult to duplicate. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

idle while the vehicle is in transport mode. The noise is noticeable because of an elevated idle speed while the vehicle is in transport mode. Do not remove the vehicle from transport mode to diagnose or perform a repair for this noise. Vehicle should only be removed from transport mode as directed by the pre-delivery procedure.

condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.

using the remote start function to start the vehicle with DTC P1594 stored in the BCM. If using the FordPass app, the app will tell the customer that the vehicle started successfully, but the customer observes that the vehicle did not start or started then shut off. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

illuminated MIL with diagnostic trouble codes (DTCs) P0351, P0352, P0353 and/or P0354 stored in the powertrain control module (PCM). This concern may be due to a poor connection at cylinder head ground G111 near coil on plug (COP) connectors 2 and 3 and body ground G110 near the turbo on the engine block. Before attempting other repairs, inspect ground G111 and G110 to ensure they are clean and properly secured. Refer to Wiring Diagram, Cell 10. If these grounds are clean and properly secured to 19 Nm (168 lb-in), proceed with normal Powertrain Control/Emissions Diagnosis (PC/ED) Manual diagnostics.

F34 open, an illuminated MIL with diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). May also exhibit an all-wheel drive (AWD) fault warning and/or traction control (TC) light on. Inspect the 14290 wiring harness at the battery junction box (BJB) under the air cleaner and/or the brake vacuum pump for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 14290 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

not auto restart after an auto stop event. Upon attempting to restart, the instrument panel may display a message instructing the customer to shift the vehicle to park and start the vehicle manually. To correct this condition, reprogram the Body Control Module(BCM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the SLTS Manual.

factory invoiced accessory (FIA) scalable remote start systems may exhibit a concern of the air distribution and temperature controls becoming locked after 5 minutes when the vehicle is started with the remote start system. Reprogram the heating ventilation and air conditioning (HVAC) module using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 107.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 19980 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

before 1-Feb-2017 may exhibit an illuminated MIL with DTC P051B. Follow the Service Procedure steps to correct the condition.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

exhibit an inoperative speed compensation volume feature. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages  SYNC.

may exhibit illuminated malfunction indicator light(MIL) with DTC P04DB(crankcase ventilation system disconnected) stored in Powertrain Control Module(PCM) memory. Disconnect crankcase pressure sensor electrical connector and remove crankcase vent tube. Inspect valve cover port with borescope. If flashing is confirmed in crankcase vent tube port replace GB5Z-6582-B valve cover(Reference Workshop Manual 303-01A Engine- 2.0L Ecoboost Removal and Installation). Engineering is currently investigating. To assist with the investigation, refer to the Professional Technician Society (PTS) website and use the report a vehicle concern link at the bottom of the OASIS report.

each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.

To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.

or before 18-Sep-2017 may exhibit a MIL illuminated with DTC P04DB (crankcase ventilation system disconnected) in powertrain control module(PCM) memory. Follow the Service Procedure steps to correct the condition.

MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Traffic Listing is not loading but all remaining Travel Link features operate properly. SiriusXM Traffic is only available on vehicles equipped with navigation, only in select markets and requires an active subscription to SiriusXM Traffic information. If SiriusXM Traffic will not load attempt the following procedure. Turn the ignition off, open and close the drivers door, wait for 3 minutes, then drive the vehicle outside to obtain a clear view of the sky. SiriusXM Traffic should recover. If SiriusXM Traffic does not recover continue to monitor OASIS for future updates. Engineering is aware of this concern and no component replacement or any software re-flashes should be performed at this time. The SYNC version can be confirmed via OASIS.

9-Jun-2016 may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0455 and/or P144C stored in the powertrain control module (PCM) memory. This may be due to a disconnected or loose evaporative emission (EVAP) system underhood vapor line. Follow the Service Procedure steps to correct the condition.

may exhibit low coolant, white exhaust smoke and an illuminated MIL if diagnostic trouble codes (DTCs) P0217, P300, P0301, P0302, P0303, P0304, P0316 and/or P1299 are present. This condition may be due to an intake manifold bolt backing out causing damage to the charge air cooler (CAC). Follow the Service Procedure steps to correct the condition.

before 20-Aug-2016 may exhibit a lack of power drivability concern with an illuminated MIL and DTC P0234 stored in powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.

built on or before 20-Aug-2016 and equipped with remote start and adaptive cruise control may exhibit DTC U0104 (lost communication with cruise control module) stored in powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.

before 20-Aug-2016 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in powertrain control module(PCM) memory. Follow the Service Procedure steps to correct the condition.

diagnostic trouble codes (DTCs) P0455, P0456, P144C and/or P1450 stored in the powertrain control module (PCM) memory. Vehicles may also exhibit a rough idle and/or slow fuel fill concern. If normal diagnosis leads to the replacement of the canister purge valve then inspect for the presence of liquid fuel in the vapor lines at the EVAP canister purge valve and the EVAP canister. Liquid fuel should not be present in the EVAP canister purge valve, EVAP canister or any of the vapor lines. Engineering is investigating this concern. Monitor OASIS for updates.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0300 and/or P0316 stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.

REMOTE START SYSTEMS MAY EXHIBIT A CONCERN OF THE AIR DISTRIBUTION AND TEMPERATURE CONTROLS BECOMING LOCKED AFTER 5 MINUTES WHEN THE VEHICLE IS STARTED WITH THE REMOTE START SYSTEM. AFTER APPROXIMATELY 5 MINUTES OF DRIVING THE AIR DISTRIBUTION AND TEMPERATURE CONTROLS LOCK AND REQUESTS FOR AIR DISTRIBUTION AND TEMPERATURE CHANGES WILL NOT OCCUR. THE HEATING VENTILATION AND AIR CONDITIONING (HVAC) CONTROLS CORRECTLY INDICATE WHEN CHANGES ARE SELECTED BUT THE REQUESTED AIR DISTRIBUTION AND TEMPERATURE CONTROL FUNCTIONS WILL NOT OCCUR. NORMAL OPERATION IS RESTORED WHEN THE KEY IS CYCLED. THIS CONCERN DOES NOT AFFECT BLOWER MOTOR OPERATION. ENGINEERING IS INVESTIGATING THIS CONCERN. MONITOR OASIS FOR UPDATES.

FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.

2.0L, 2.7L OR 3.0L GASOLINE TURBOCHARGED DIRECT INJECTION(GTDI) ECOBOOST ENGINES MAY EXHIBIT MALFUNCTION INDICATOR LIGHT(MIL) ON WITH DIAGNOSTIC TROUBLE CODES(DTC) P1013, P1015 AND/OR P1016 STORED IN POWERTRAIN CONTROL MODULE(PCM). CHECK TURBOCHARGER WASTEGATE CONTROL HOSES FOR WATER/ICE RESTRICTIONS OR PINCHING AT ZIP-TIE ON ENGINE CAM COVER RETAINER(2.7L AND 3.0L ONLY). IF RESTRICTION IS FOUND ON CAM COVER RETAINER, CUT ZIP TIE AND CLEAR DTCS. IF WATER/ICE RESTRICTION IS FOUND, DRAIN HOSES, REASSEMBLE AND CLEAR DTCS. IF DTCS RETURN, REFER TO WORKSHOP MANUAL (WSM) OR POWERTRAIN CONTROL EMISSIONS DIAGNOSIS (PCED) MANUAL FOR NORMAL DIAGNOSTICS. ENGINEERING IS INVESTIGATING THE CONCERN, MONITOR OASIS FOR FURTHER UPDATES.

CONTROL BLOWER MOTOR WITH OR WITHOUT A LACK OF AIRFLOW FROM PANEL REGISTERS AND MAY ALSO HAVE AN ODOR. THIS CONCERN MAY BE DUE TO SMALL ANIMALS THAT CAN ENTER THE BLOWER MOTOR HOUSING AREA THROUGH THE AIR INLET DUCT AND CAUSE DAMAGE TO THE AIR INLET DUCT ASSEMBLY AND/OR BLOWER MOTOR ASSEMBLY. THE SMALL ANIMALS MAY DEPOSIT FOREIGN MATERIAL IN THE BLOWER MOTOR ASSEMBLY AND AIR INLET HOUSING THAT MAY CAUSE LACK OF AIRFLOW, NOISE AND/OR VIBRATION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

EXHIBIT INOPERATIVE FRONT POWER WINDOWS DUE TO AN OPEN FUSE 15 IN THE RJB. FUSE 15 IN THE RJB MAY OPEN IF THE FRONT WINDOWS ARE OPERATED AT THE SAME TIME AND THE SWITCHES ARE HELD AT THE STOPS. THIS MAY OCCUR IN COLDER WEATHER DUE TO INCREASED CURRENT REQUIREMENTS OF THE MOTORS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

AND AN ODOMETER READING 16,000 KM (10,000 MILES) OR ABOVE MAY EXHIBIT LOW COOLANT, WHITE EXHAUST SMOKE AND MAY ALSO EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0217, P0300, P0301, P0302, P0303, P0304, P0316 AND/OR P1299. THIS CONDITION MAY BE DUE TO AN INTAKE MANIFOLD BOLT BACKING OUT CAUSING DAMAGE TO THE CHARGE AIR COOLER (CAC). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION

MAY EXHIBIT LOW COOLANT, WHITE EXHAUST SMOKE AND AN ILLUMINATED MIL IF DIAGNOSTIC TROUBLE CODES (DTCS) P0217, P300, P0301, P0302, P0303, P0304, P0316 AND/OR P1299 ARE PRESENT. THIS CONDITION MAY BE DUE TO AN INTAKE MANIFOLD BOLT BACKING OUT CAUSING DAMAGE TO THE CHARGE AIR COOLER (CAC). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION

BEFORE 23-DEC-2016 MAY EXHIBIT A DISCHARGED BATTERY. A REPETITIVE CYCLING NOISE SIMILAR TO A CD EJECTING NOISE MAY ALSO BE PRESENT. IF EXCESSIVE BATTERY DRAIN IS PRESENT AND ELIMINATED WITH THE RADIO BATTERY POWER FUSE REMOVED, REPROGRAM THE AUDIO CONTROL MODULE (ACM) TO THE LATEST CALIBRATION USING THE INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 104.02 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 18C869 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

REMOTE START SYSTEMS MAY EXHIBIT A CONCERN OF THE LAST USER SETTING OF THE HEATING VENTILATION AND AIR CONDITIONING (HVAC) SYSTEM IS NOT MAINTAINED WHEN THE VEHICLE IS STARTED WITH THE REMOTE START SYSTEM. AIRFLOW MAY BE DEFAULTED TO THE DEFROST DUCTS WHEN THIS OCCURS. REPROGRAM THE HEATING VENTILATION AND AIR CONDITIONING (HVAC) MODULE TO THE LATEST CALIBRATION USING THE INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 104.02 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 19980 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

23-DEC-2016 MAY EXHIBIT A DISCHARGED BATTERY. A REPETITIVE CYCLING NOISE SIMILAR TO A CD EJECTING NOISE MAY ALSO BE PRESENT. IF EXCESSIVE BATTERY DRAIN IS PRESENT AND ELIMINATED WITH THE RADIO BATTERY POWER FUSE REMOVED, REPROGRAM THE AUDIO CONTROL MODULE (ACM) TO THE LATEST CALIBRATION USING THE INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 103.05A OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 18C869 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

ACCESSORY (FIA)REMOTE START SYSTEM MAY EXHIBIT A CONCERN THAT THE ENGINE CANNOT BE REMOTE STARTED USING THE FORDPASS APPLICATION IF THE FOA/FIA REMOTE START SYSTEM HAS NOT BEEN INSTALLED. TO VERIFY IF THE FOA/FIA REMOTE START SYSTEM HAS BEEN INSTALLED ON THE VEHICLE, INSPECT THE WINDSHIELD FOR THE PRESENCE OF THE REMOTE START ANTENNA, TYPICALLY LOCATED ON THE GLASS BEHIND THE INTERIOR REAR VIEW MIRROR OR NEAR THE A-PILLAR. ANOTHER METHOD OF INSPECTION IS TO VERIFY THAT REMOTE START OPTIONS ARE AVAILABLE UNDER SETTINGS - VEHICLE - REMOTE START - IN THE INSTRUMENT CLUSTER. THE FOA/FIA REMOTE START KIT INSTALLATION AND REMOTE START ACTIVATION PROCEDURE ARE UNDER THE ACCESSORY INSTALLATION TAB IN THE ON-LINE WORKSHOP MANUAL.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED

FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.

ESCAPE/EXPLORER/MKC/FUSION AND MKZ VEHICLES EQUIPPED WITH SYNC 3 MIGHT EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. ENGINEERING IS AWARE OF THIS POSSIBILITY AND IT IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORTATION MODE. IT IS BENEFICIAL TO EXTENDED BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. IF THE VEHICLE SHOULD EXHIBIT A BLANK SCREEN OR OTHER SYNC SYMPTOMS AFTER IT HAS BEEN TAKEN OUT OF TRANSPORT MODE, REFER TO WORKSHOP MANUAL, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

5/18/2016, MAY EXHIBIT FALSE DTC P1935(BRAKE SWITCH/SENSOR SIGNAL) AND/OR P061E(INTERNAL CONTROL MODULE BRAKE SIGNAL PERFORMANCE) STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

CONTROL MODULE REPROGRAMMING

WHILE THE VEHICLE IS IN TRANSPORT MODE. THE NOISE IS NOTICEABLE BECAUSE OF AN ELEVATED IDLE SPEED WHILE THE VEHICLE IS IN TRANSPORT MODE. DO NOT REMOVE THE VEHICLE FROM TRANSPORT MODE TO DIAGNOSE OR PERFORM A REPAIR FOR THIS NOISE. VEHICLE SHOULD ONLY BE REMOVED FROM TRANSPORT MODE AS DIRECTED BY THE PRE-DELIVERY PROCEDURE.

POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.

SIRIUSXM TRAFFIC LISTING IS NOT LOADING BUT ALL REMAINING TRAVEL LINK FEATURES OPERATE PROPERLY. SIRIUSXM TRAFFIC IS ONLY AVAILABLE ON VEHICLES EQUIPPED WITH NAVIGATION, ONLY IN SELECT MARKETS AND REQUIRES AN ACTIVE SUBSCRIPTION TO SIRIUSXM TRAFFIC INFORMATION. IF SIRIUSXM TRAFFIC WILL NOT LOAD ATTEMPT THE FOLLOWING PROCEDURE. TURN THE IGNITION OFF, OPEN AND CLOSE THE DRIVERS DOOR, WAIT FOR 3 MINUTES, THEN DRIVE THE VEHICLE OUTSIDE TO OBTAIN A CLEAR VIEW OF THE SKY. SIRIUSXM TRAFFIC SHOULD RECOVER. IF SIRIUSXM TRAFFIC DOES NOT RECOVER CONTINUE TO MONITOR OASIS FOR FUTURE UPDATES. ENGINEERING IS AWARE OF THIS CONCERN AND NO COMPONENT REPLACEMENT OR ANY SOFTWARE RE-FLASHES SHOULD BE PERFORMED AT THIS TIME. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

BEFORE 5/11/2016 MAY EXHIBIT DIAGNOSTIC TROUBLE CODE (DTC) P164C STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY WITH AN ILLUMINATED CHECK ENGINE LIGHT, LACK OF POWER AND/OR NO AUTOMATIC ENGINE RESTART AFTER AN EXTENDED STOPSTART EVENT.

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

binding/shudder and/or bump/clunk from the rear drive unit (RDU) when turning at low speeds and parking lot maneuvers. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM. T

Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

message center with no trailer attached to the vehicle. To correct this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part (19H332) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

a trailer lamp out warning and/or blind spot information system (BLIS) not available warning without a trailer connected to the vehicle. Access connectors C439 (4 pin) and C432 (12 pin) within the trailer connector harness (15K868). Refer to Wiring Diagram, Cell 151. Inspect connectors for corrosion and/or water contamination. Clean as required and add electrical grease (XG-12 or equivalent). Make certain the protective cover over C439 is installed and fully seated to prevent future water intrusion. For claiming, use causal part 15K868 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

a trailer lamp out warning and/or blind spot information system (BLIS) not available warning without a trailer connected to the vehicle. Access connectors C439 (4 pin) and C432 (12 pin) within the trailer connector harness (15K868). Refer to Wiring Diagram, Cell 151. Inspect connectors for corrosion and/or water contamination. Clean as required and add electrical grease (XG-12 or equivalent). Make certain the protective cover over C439 is installed and fully seated to prevent future water intrusion. For claiming, use causal part 15K868 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

flicker during transitions between day/night mode and/or during auto headlamp on/off. The FDIM utilizes a ramp up and ramp down strategy of controlling the back lighting when the display setting is in auto dimming mode. This is a normal condition that does not affect the function or durability of the FDIM. Auto dimming mode can be turned off to minimize the ramp up and ramp down lighting strategy. To turn off the auto dimming mode feature in the FDIM display: select> FDIM settings> Display settings> Auto Dim selection. Do not confuse the auto dimming mode selection with the selection for auto day/night operation. Turning off auto dimming mode only effects the back lighting strategy and does not affect any other function or FDIM reliability.

and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.

28-Jul-2016 and through 23-Aug-2018 may exhibit an inoperative heating, ventilation and air conditioning (HVAC) system display and no HVAC operation after a key on event. When one of the HVAC controls are manipulated the system wakes up and will resume normal operation. To correct the concern, reprogram the HVAC module to the latest calibration using the latest version of the appropriate Ford diagnostic scan tool. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.

after 28-Jul-2016 may exhibit an inoperative heating, ventilation and air conditioning (HVAC) system display and no HVAC operation after a key on event. When one of the HVAC controls are manipulated the system wakes up and will resume normal operation. To correct the concern, reprogram the HVAC module to the latest calibration using the latest version of the appropriate Ford diagnostic scan tool. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

liftgate, the hands-free liftgate function will become inoperative. Hands-free liftgate function can be restored by replacing the existing hands-free liftgate actuation upper sensor (14F680), lower sensor (14F680), stone deflector (17779), hands-free liftgate actuation module (14B291), plastic fasteners (N807951S) and screws (W506964) that are required for the factory installed trailer hitch receiver with hands-free liftgate option. Replacement of these parts to restore hands-free liftgate function is not warrantable. Regardless of trailer hitch configuration, the hands-free liftgate system cannot be added to a vehicle that was originally built without the hands-free liftgate option.

2017-2018 Escape vehicles with Sony audio systems may exhibit an inoperative speed compensated volume feature. This may be due to the calibration in the audio control module (ACM). To correct the concern, reprogram the ACM to the latest calibration using the appropriate Ford scan tool release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

DTC U0164 in the body control module (BCM). This may be due to loss of communication or incomplete module configuration. Before further diagnosis, complete a battery reset per the Workshop Manual (WSM), Section 414-01. Clear the DTCs and complete a FCIM self-test. If the DTCs are no longer present, no further action is required. For claiming, use causal part 19980 and applicable labor operations in section 11 of the service labor time standards (SLTS) manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

DTC U0164 in the body control module (BCM). This may be due to loss of communication or incomplete module configuration. Before further diagnosis, complete a battery reset per the Workshop Manual (WSM), Section 414-01. Clear the DTCs and complete a FCIM self-test. If the DTCs are no longer present, no further action is required. For claiming, use causal part 19980 and applicable labor operations in section 11 of the service labor time standards (SLTS) manual.

trailer lamp out warning and/or BLIS not available warning without a trailer connected. Access connectors C439 (4 pin) and C432 (12 pin) in the trailer tow harness. Inspect for corrosion and/or water contamination. Clean as required and add electrical grease (XG-12). Install and fully seat cover on C439 to prevent future water entry. Reprogram the trailer module (TR) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 105.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 15K868 and applicable labor operations in Section 10 of the SLTS Manual, use causal part 19H332 for reprogram.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

To correct this condition, reprogram the Remote Frequency Actuator (RFA) module to the latest level using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.06 or higher. For claiming, use causal part 19G481 and applicable labor operations in section 10 of the SLTS manual.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

U0164 in the body control module (BCM). This may be due to loss of communication or incomplete module configuration. Before further diagnosis, complete a battery reset per the Workshop Manual (WSM), Section 414-01. Clear the DTCs and complete a FCIM self-test. If the DTCs are no longer present, no further action is required. For claiming, use causal part 19980 and applicable labor operations in section 11 of the service labor time standards (SLTS) manual.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

This may be due to water in connector C134(20 pin) in the left front fender apron. If a vehicle comes in with this condition, access connector C134 in the 14290 harness. Refer to Wiring Manual. Check connector C134 for corrosion and/or water contamination. If present, replace the pigtail harness (Refer to Pigtail Application Guide Under Repair Kits in the Wiring Manual) and add electrical grease (XG-12). For claiming, use causal part 14S411 and applicable labor operations in section 11 of the service labor time standards (SLTS) manual

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

inoperative audio system after a battery disconnect/reconnect. Make sure battery is at full state of charge before attempting to restore audio operation. Audio system operation should be restored by disconnecting the negative battery cable for 10 minutes and reconnecting. If a vehicle service procedure requires a battery disconnect/reconnect ensure radio functionality is verified before vehicle is released to the customer. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for updates.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

OR A SYSTEM LOCK UP WHEN THE PHONE IS CONNECTED. APPLINK MAYBE INOPERATIVE, OR THE SYSTEM MAY PERFORM RANDOM REBOOTS DURING AN IGNITION CYCLE WITH THE PHONE CONNECTED. DETERMINE IF THE CUSTOMER HAS AN ANDROID PHONE WITH THE BASEBALL APPLICATION MLB.COM AT BAT INSTALLED. IF THE CUSTOMER DOES NOT HAVE THIS APPLICATION LOADED THEN PROCEED TO THE WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. IF THE CUSTOMER DOES HAVE THIS APPLICATION LOADED VERIFY IF THE VERSION IS 5.1.3 OR LOWER ON THE ANDROID PHONE. IF THE ANDROID PHONE WITH MLB.COM AT BAT HAS VERSION 5.1.3 OR LOWER PLEASE RECOMMEND THAT THEY UPDATE THEIR APP TO VERSION 5.2 OR HIGHER AND RETEST FOR THE CUSTOMER SYMPTOM. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

MODULE SETTINGS DURING KIT INSTALLATION

Workshop Manual (WSM), Section 413-01 procedure. This may be due to the instrument panel cluster (IPC) software that was updated and/or an IPC replacement during a previous service visit. To correct the condition, follow the Service Procedure to replace the IPC with an updated service part.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

This may be due to the striker wing position relative to striker. To correct the condition, adjust the striker wings to the specified specification.

This may be due to the adjustment of the striker, latch, liftgate margins, flushness and/or striker wings. To resolve the condition, adjust the striker position or the striker wings.

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

This is the normal vent position for optimal noise, vibration, harshness (NVH) and windnoise qualities. When the vent is closed, the front sliding glass panel will open to the 10 mm (.394 in) position and then close. The front sliding glass panel also opens to the 10 mm (.394 in) position to give the front sliding glass panel enough clearance before it opens to the rearward position. This is a normal operating characteristic of the front sliding glass panel. No repairs are required.

EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

power liftgate that exhibits bounce back and/or will not cinch. Follow the Service Procedure steps to correct this condition.

a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.

Follow the Service Procedure steps to correct the condition.

THIS IS THE NORMAL VENT POSITION FOR OPTIMAL NVH/WINDNOISE QUALITIES. WHEN THE VENT IS CLOSED, THE MOONROOF WILL OPEN TO THE 10 MM POSITION THEN CLOSE. THE SLIDING GLASS ALSO OPENS TO THE 10 MM POSITION TO GIVE THE GLASS ENOUGH CLEARANCE BEFORE IT OPENS TO THE REARWARD POSITION. THIS IS THE NORMAL OPERATING CHARACTERISTIC. NO REPAIRS ARE REQUIRED.

TO THE INITIALIZATION PROCEDURE FOR BOTH THE ROOF OPENING PANEL AND THE SHIELD(SUNSHADE). REFER TO WORKSHOP MANUAL, SECTION 501-17. IN STEP 2 FOR THE PROCEDURES THAT MUST BE COMPLETED WITHIN 5 SECONDS, DO NOT RELEASE THE TILT SWITCH(SLIDING GLASS PANEL CLOSE SWITCH) OR THE SHIELD (SUNSHADE) CONTROL CLOSE SWITCH. THE SWITCHES MUST BE HELD DOWN DURING THIS STEP. PLEASE NOTE THAT VEHICLES BUILT BETWEEN 06-JUN-2016 AND 10-JUN-2016 MAY HAVE EITHER THE NEW OR OLD INITIALIZATION PROCEDURE. VEHICLES BUILT ON OR AFTER 03-DEC-2016 REVERTED BACK TO THE ORIGINAL INITIALIZATION PROCEDURE.

THE 2016-2017 WORKSHOP MANUAL SECTION 501-11 WAS UPDATED 8/2016 WITH REVISED DIAGNOSTICS, THE 2015 WSM UPDATES WILL FOLLOW LATER. REFER TO THE 2016-2017 WSM REVISED DIAGNOSTICS FOR ANY OF THE FOLLOWING CONCERNS: ONE-TOUCH UP FEATURE IS INOPERATIVE, WINDOW DOOR GLASS DOES NOT TRAVEL FULLY TO EITHER OPEN/CLOSED POSITION,AND WINDOW BOUNCES BACK CONCERNS. AT THE BEGINNING OF PINPOINT TEST E, CARRY OUT THE INITIALIZATION PROCEDURE ON THE SUSPECT POWER WINDOW, BEFORE CONTINUING THE PINPOINT TEST. REFER TO: POWER DOOR WINDOW INITIALIZATION - VEHICLES WITH: ONE-TOUCH OPEN AND CLOSE FRONT WINDOWS (501-11 GLASS, FRAMES AND MECHANISMS, GENERAL PROCEDURES).

THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED.

RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages  SYNC.

display screen when using the parking aid camera. This is due to the convex camera lens to provide as much viewing angle as possible. This is a normal vehicle characteristic and no repairs or adjustments should be attempted to correct this condition.

INTERMITTENT CONCERN WHERE THE AUDIO CUTS OUT AND THE RADIO DISPLAYS A NO SIGNAL MESSAGE WHILE DRIVING IN OPEN SKY CONDITIONS IN CERTAIN LOCATIONS IN YOUR AREA. THIS MAY BE DUE TO INTERFERENCE WITH CELLULAR PHONE TOWER SIGNALS. IF A VEHICLE DISPLAYS THIS CONDITION NEAR CELLULAR PHONE TOWERS, REPLACE THE AUDIO UNIT ANTENNA WITH PART NUMBER HJ5Z-18936-BA. REFER TO WORKSHOP MANUAL(WSM), SECTION 415-00 FOR REMOVAL AND INSTALLATION INSTRUCTIONS. USE APPLICABLE LABOR OPERATION(S) IN THE SLTS MANUAL SECTION 11.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The noise most commonly occurs after the brakes have warmed up, however the noise may occur during other driving conditions. If the front brakes display a continuous squeal noise, install front lining kit CV6Z-2001-N. Reference Workshop Manual (WSM) Section 206-03, removal and installation instructions. Use causal part 2001 and refer to section 2 of the SLTS manual for applicable labor operations.

electric park brake warning indicator with diagnostic trouble codes (DTCs) C1034, C1A43, C2005, C2007, C2008 and/or U2002. Four wheel drive (4WD) vehicles may also exhibit an anti-lock brake system (ABS) lamp illuminated with DTCs C003A or C0037. Follow the Service Procedure steps to correct the condition.

1-OCT-2016 MAY EXHIBIT A RATTLE AND/OR CLUNKING NOISE FROM THE REAR SUSPENSION WHILE DRIVING OVER BUMPS AND/OR MAKING TURNS AT LOW SPEEDS. SUSPECT REAR SHOCK ABSORBERS WILL COMPRESS 2-5 INCHES OF TRAVEL BEFORE SIGNIFICANT RESISTANCE IS OBSERVED. IF WORKSHOP MANUAL (WSM), SECTION 100-04 DIAGNOSTICS INDICATE A RATTLE AND/OR CLUNKING NOISE IS COMING FROM THE REAR SHOCK ABSORBER(S) THEN REFER TO WSM, SECTION 204-02 AND REPLACE THE REAR SHOCK ABSORBER(S)AS REQUIRED. FOR CLAIMING, USE CAUSAL PART 18125 AND APPLICABLE LABOR OPERATIONS IN SECTION 5 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

EXHIBIT FRONT BRAKE SQUEAL WHEN APPLYING THE BRAKES. THE NOISE MOST COMMONLY OCCURS AFTER THE BRAKES HAVE WARMED UP, HOWEVER THE NOISE MAY OCCUR DURING OTHER DRIVING CONDITIONS. IF THE FRONT BRAKES DISPLAY A CONTINUOUS SQUEAL NOISE, INSTALL FRONT LINING KIT CV6Z-2001-N. REFERENCE WORKSHOP MANUAL (WSM) SECTION 206-03, REMOVAL AND INSTALLATION INSTRUCTIONS. USE CAUSAL PART 2001 AND REFER TO SECTION 2 OF THE SLTS MANUAL FOR APPLICABLE LABOR OPERATIONS.

ELECTRIC PARK BRAKE WARNING INDICATOR WITH DIAGNOSTIC TROUBLE CODES (DTCS) C1034, C1A43, C2005, C2007, C2008 AND/OR U2002. FOUR WHEEL DRIVE (4WD) VEHICLES MAY ALSO EXHIBIT AN ANTI-LOCK BRAKE SYSTEM (ABS) LAMP ILLUMINATED WITH DTCS C003A OR C0037. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

WARNING WITH DIAGNOSTIC TROUBLE CODES (DTCS) C1034, C1A43, C2005, C2007, C2008 AND/OR U2002. 4 WHEEL DRIVE (4WD) VEHICLES MAY ALSO EXHIBIT AN ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT ON WITH DTCS C003A OR C0037. IF A VEHICLE COMES IN FOR THIS CONCERN, INSPECT THE ELECTRIC PARK BRAKE/BRAKE SKID CONTROL WIRING HARNESS (2C055) IN THE REAR ON BOTH SIDES. INSPECT THE HARNESSES FOR DAMAGE WHERE THEY ARE ROUTED CLOSEST TO THE REAR WHEELS. IF DAMAGED, REPAIR AS REQUIRED AND TIE STRAP BOTH HARNESSES TO GAIN SUFFICIENT CLEARANCE AWAY FROM BOTH REAR WHEELS. APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.

Upon attempting to restart, the instrument panel may display a message instructing the customer to shift to park and start the vehicle manually. To correct this condition, reprogram the body control module (BCM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. If the BCM software is currently at the latest level available, refer to Workshop Manual (WSM), Section 303-06A and/or powertrain control/emissions diagnosis (PC/ED) manual for an auto stop/start diagnostic trouble code (DTC) or GSB0000153 for auto stop/start system information and diagnostics.

center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.

Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 'C to 5 'C (23 'F to 41 'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.

Prior to performing any road force balancing procedures or related diagnosis, make sure the vehicle tire pressure is correct and is driven a minimum of 24 Km (15 miles) to eliminate any possible flat spotting conditions and potential misdiagnosis. Refer to Workshop Manual (WSM), Section 204-04A for further information. In addition, it is recommended that diagnosis of tire/wheel vibration should not be performed on tires with less than 320 Km (200 miles). Some initial tire/wheel vibration issues (such as flat spotting) may correct themselves after the tires have been in service for 320 Km (200 miles). Setting tire pressure to the correct placard pressure is contained within pre-delivery inspection.

to short term flat spotting in the tires. Follow the Service Procedure steps to correct the condition.

to short term flat spotting in the tires. Follow the Service Procedure steps to correct the condition.

SHORT TERM FLAT SPOTTING IN THE TIRES. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

This may be due to a insufficient/low refrigerant charge. If a vehicle displays a lack of cooling performance during PDI, inspect for a leak. Refer to the diagnostics in Workshop Manual (WSM), Section 412-00 for A/C leak detection. Many times when the system is only evacuated and refilled to the proper level at PDI the customer will return for a lack of cooling performance concern. A refrigerant leak will usually be identified as the root cause.

DISTRIBUTION FROM THE INSTRUMENT PANEL REGISTERS WHEN PANEL MODE IS SELECTED ON THE HEATER VENTILATION AIR CONDITIONING (HVAC) CONTROL PANEL. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

DISTRIBUTION FROM THE INSTRUMENT PANEL REGISTERS WHEN PANEL MODE IS SELECTED ON THE HEATER VENTILATION AIR CONDITIONING (HVAC) CONTROL PANEL. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

If the rear suspension front lower arm requires replacement, an updated part is available through the parts catalog. Refer to Workshop Manual (WSM), Section 204-02 for removal and installation.

If the rear suspension front lower arm requires replacement, an updated part BV6Z-5500-D with a solid bushing is available. Refer to Workshop Manual (WSM), Section 204-02 for removal and installation.

SOME OF THE REASONS WOULD INCLUDE WINDSHIELD REPLACEMENT, SUSPENSION REPAIR, ALIGNMENT OR MODIFICATIONS, INTERIOR MIRROR REPLACEMENT OR REPLACEMENT OF THE IPMA CAMERA. ON PREVIOUS INTEGRATED DIAGNOSTIC SYSTEM (IDS) SOFTWARE RELEASES THE LDWS CAMERA ALIGNMENT FUNCTION IS NOT PRESENT. USE IDS VERSION 101.01 OR HIGHER WHEN PERFORMING THE LDWS CAMERA ALIGNMENT FUNCTION.

VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

This video illustrates the speed and simplicity of the dongle re-flash process. Non-Traditional Repair Approaches: The dongle re-flash process allows for an improved customer experience, dealer service efficiency, speed, and no need for an appointment, service bay, or trained technician. Service Action: All dealers will be shipped at least one dongle by February 28, 2020. Shipment of dongles began the week of February 17, 2020. Dealers with the largest VIN count received the initial shipment. Dealers may request additional dongles from the SSSC as needed. Technician time clocking is not required for this program when using the 19B37 dongle.

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

IF A CUSTOMER HAS A STEERING PULL OR VEHICLE DRIFT CONCERN AND THE VEHICLE IS EQUIPPED WITH THE LANE KEEPING SYSTEM, ENSURE THAT THE CUSTOMER IS AWARE OF THE LANE KEEPING AID FEATURE ON THEIR VEHICLE AND HOW IT WORKS. THE SYSTEM DETECTS UNINTENTIONAL DRIFTING TOWARD THE OUTSIDE OF THE LANE AND ALERTS OR AIDS YOU TO STAY IN THE LANE THROUGH THE STEERING SYSTEM AND INSTRUMENT CLUSTER DISPLAY. LANE KEEPING AID MODE PROVIDES AN ASSISTANCE STEERING TORQUE INPUT TOWARD THE LANE CENTER WHEN THE SYSTEM DETECTS AN UNINTENDED LANE DEPARTURE. FURTHER INFORMATION ON THE LANE KEEPING SYSTEM CAN BE FOUND IN THE OWNERS GUIDE. IF THE CUSTOMERS CONCERN IS THE LANE KEEPING SYSTEM FUNCTIONING AS INTENDED, DO NOT ATTEMPT TO REPAIR.

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.