2023 Ford E-450 TSBs

remove the flex plate bolts AL3Z-6379-BA from the parts list as these bolts are in kit LC3Z-6781-A, update the claim quantity of the part number W709771-S440 to 9 pieces (F-650/F750-Engine Replacement), W706447-S437 and W715068-S437 to 4 pieces, W712861-S439 to 8 pieces(F-Super Duty Pickup And Chassis Cab-Engine Replacement) / 8 pieces (F-53 Motorhome/F-59 Stripped Chassis Cab/F-650,F750 Engine Replacement) / W714286-S442 to 4 pieces (F-Super Duty Pickup And Chassis Cab-Camshaft and Tappet Repair / F-Super Duty Pickup And Chassis Cab-Engine Replacement), include LC3Z-6020-A for the Engine replacement lists, include 1 fuel injector seal kit to the Camshaft and Tappet repair lists, include 4 pieces of W520114-S440 to the E Series-Camshaft and Tappet Repair list, and update the engine oil part numbers XO-5W30-Q1SP and CXO-5W30-LSP6. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing ro

vehicles equipped with a Dana rear axle and built on or after 01-Jul-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.

Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.

Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2026 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. This may be due to the starter motor drive gear not retracting after starting. To correct this condition, inspect the starter motor drive gear and shaft. If the starter motor drive gear slides back and forth by hand and/or shows signs of scoring or damage, replace the starter motor following Workshop Manual (WSM), Section 303-06 Starting System > Removal and Installation > Starter.

Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

Control Module (PCM) Software Update REASON FOR THIS SUPPLEMENT Software Availability Update: Software is now available to repair 2021-2022 and 2025 Model Year Econoline vehicles. The service action has been updated accordingly. Technical Information: IDS programing information has been added for 2021-2023 Model Year Econoline Vehicles.

Control Module (PCM) Software Update In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate

Powertrain Control Module Software Update

vehicles equipped with a Dana rear axle and built on or after 01-Nov-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.

equipped with a gas engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect incorrectcylinder to DTC mapping, the PCM will shut off fuel to the cylinder that the PCM has triggered a DTC against. Diagnosing the cylinder that does not set an ignition DTCand drops during the power balance test, will verify the identity of the cylinder that has the concern. If only onecylinder is dropping out, start diagnostics with that cylinder. Refer to the Workshop Manual, Section 303-07A/C.

F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Adding Not OTA Capable Owner letters. Other documents submitted 01/02/24 & Received OTA letters submitted on 02/01/24

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Some 2021-2023 E-Series vehicles may exhibit a lack of air flow due to an inoperative heating, ventilation, and air conditioning (HVAC) blower motor. This may be due to a damaged fuse F2 (50A) in the battery junction box (BJB). To correct the condition, replace the BJB, pigtail connector, and replace fuse F2 in the new BJB with the listed service replacement part.

This may be due to a damaged fuse F2 (50A) in the battery junction box (BJB). To correct the condition, replace the BJB and replace fuse F2 in the new BJB with the listed service replacement part.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 and/or P0455 stored in the powertrain control module (PCM). This may be due to a improper fuel filler cap installation and/or outside contamination on the fuel cap sealing surface. The fuel filler cap requires multiple turns to seal properly and should be clean of any debris on sealing surface. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. If the DTCs return after the fuel filler cap is cleared of debris and properly seated, refer to Workshop Manual (WSM), Section 303-13 > pinpoint test HX.

2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 stored in the powertrain control module (PCM). This may be due to a loose fuel filler cap. The fuel filler cap design has changed, requiring multiple turns to seal properly. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. For further diagnostics, refer to Workshop Manual (WSM), Section 303-13 - pinpoint test HX.

lamp (MIL) with diagnostic trouble codes (DTC) P0128, P0420, and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.