2009 Ford E-350 TSBs

with a TorqShift transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700

MODEL 2003-2014 F-SUPER DUTY, E SERIES, EXCURSION, F-53 MOTORHOME CHASSIS, LOW CAB FORWARD. *PE

5 VOLTS, DISCONNECT THE ENGINE COOLING FAN CLUTCH, ELECTRONICALLY, AND RECHECK VOLTAGE. MODEL 2003-2007 F SUPER DUTY, 2004-2010 E SERIES, 2003-2005 EXCURSION.

MODEL 2008-2009 F-53 MOTORHOME CHASSIS, LOW CAB FORWARD, 2008-2010 F-250, F-350, 2008-2011 E-350, E-450, F-450, F-550, 2011 F-53 MOTORHOME CHASSIS, F-50 COMMERCIAL STRIPPED CHASSIS. *PE

TRANSMISSION MAY EXHIBIT MIL WITH DTCS P0751, P0730 AND/OR P2700. *JS

THERE MAY BE TWO TROUBLE CODES STORED. THE PROBLEM MAY BE CAUSED BY AFTERMARKET GENERATORS INSTALLED OR MODIFICATIONS TO THE FRONT END DRIVE. E-350/450. *RM

SOME VEHICLES AND TRUCKS EQUIPPED WITH 6.0L ENGINE MAY EXHIBIT A RUNS ROUGH, LACKS POWER, HARD TO START, NO START CONCERN WITH OR WITHOUT DIAGNOSTIC TROUBLE CODE (DTC) P0611 CODE OR VARIOUS INJECTOR CIRCUIT CODES. *PE

ACCOMPANIED WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0611, P1378 AND/OR ALL 8 INJECTOR CIRCUIT CODES. *PE

released to assist with proper repair of the 4R75E transmission in 2008 Mark LT, 2008-2010 F-150, 2008-2010 / 2013-2014 E-Series, 2008-2011 Crown Victoria, Grand Marquis and Town Car vehicles that exhibit a grinding, whine-type noise, vibration and/or gear slippage while driving, or a loss of reverse resulting from a planetary gear assembly failure.

GRINDING, GEAR SLIPPAGE, WHINE TYPE NOISE, VIBRATION, WHILE DRIVING OR LOSS OF REVERSE. *PE

CLUTCH FAILURE AND DIAGNOSTIC TROUBLE CODE (DTC) P0733 AND/OR P0734. MODEL 2008-2013 MARK LT, F-150, CROWN VICTORIA, GRAND MARQUIS, TOWN CAR, E SERIES. *PE

THIS IS A SOFTWARE PROBLEM. *RM

SOME VEHICLES MAY EXHIBIT STEERING WANDER OR FREE PLAY. STEERING GEAR MESH LOAD ADJUSTMENT. FRONT END ALIGNMENT MAY BE ADJUSTED TO IMPROVE THE WANDER/FREE PLAY CONDITION. STICKY ON CENTER FEEL MAY ALSO BE DUE TO BALL JOINT TIGHTNESS AND/OR HIGH FRICTION/RUBBING OF THE INTERMEDIATE SHAFT BOOT. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

*RM

*PE

THE EMISSION CONTROL LABELS DO NOT MEET STANDARDS. *RM

*RM

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

BANK 2, SENSOR 1) WILL APPEAR WHEN THE MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED ON SOME TRUCKS AND SERVICE PROCEDURE IS PROVIDED. MODEL 2009-2011 3-150, 250, 350, 450. *PE

The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.