2014 Ford E-250 TSBs

(DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

(DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

with a TorqShift transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

(DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

FUEL CONDITIONING MODULE (DFCM) AND/OR MAY 10/1/1 PRESSURE FUEL LINES W/O DIAGNOSTIC TROUBLE CODE POOSA. *TA

MODEL 2003-2014 F-SUPER DUTY, E SERIES, EXCURSION, F-53 MOTORHOME CHASSIS, LOW CAB FORWARD. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

released to assist with proper repair of the 4R75E transmission in 2008 Mark LT, 2008-2010 F-150, 2008-2010 / 2013-2014 E-Series, 2008-2011 Crown Victoria, Grand Marquis and Town Car vehicles that exhibit a grinding, whine-type noise, vibration and/or gear slippage while driving, or a loss of reverse resulting from a planetary gear assembly failure.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

MODULE MEMORY DUE TO CRYSTALS DEVELOPING ON THE INJECTOR NOZZLE. *LJ

IMPROVED COOLING FAN CIRCUIT DUE TO A LACK OF AIR CONDITIONING, A MALFUNCTIONING INDICATOR LAMP (MIL) AND OVERHEATING. *PE

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.

*LJ