2021 Fiat 500X TSBs

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? /B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Customers may notice the following:Message on the Instrument Panel Cluster (IPC) - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may notice the following:Message on the Instrument Panel Cluster (IPC) - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Customers may notice the following:Message on the Instrument Panel Cluster (IPC) - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P006C-MAP - Turbocharger Inlet Air Pressure Correlation. "

installed in the vehicle.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Order the "R" part number for all orders:

this is normal and not a defect.

semi and full synthetic oils.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

Customers may experience the following shift quality issue:1?2 upshift lag/delay when accelerating from a stop.

system

Library for specifications so a suitable alternative can be used

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

B)