2016 Fiat 500 TSBs

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

operation of the Tire Pressure Monitor (TPM) feature. The customer may notice that the TPM lamp is illuminated. On further inspection the technician may find Diagnostic Trouble Codes (DTCs) C1012-88 TPM Sensor Location Undetermined - BUS off, and/or C1015-88 Front/Rear Tire Pressure Sensor Location Undetermined.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

A small number of customers may experience the loss of air conditioning operation (AC will not turn on).

Matte finishes are different from other automotive paints and need special care to maintain their appearance. Typical gloss paints use a high gloss clear-coat finish that reflects light and gives a shiny appearance. A matte finish uses a different coating that diffuses light, providing a unique ?flat? finish. Unlike a typical high gloss clear-coat, damage to the matte coating (such as scratches or wear from aggressive cleaning) cannot be polished or buffed out. Once an area is damaged or becomes shiny, the ?flat? appearance cannot be restored.

module with the latest available software. A small number of customers may experience the loss of air conditioning operation.

Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find the following Diagnostic Trouble Code (DTC) has been set in the PCM. P0141 - O2 Sensor 1/2 Heater Performance.

Power Steering (EPS) module with the latest available software to correct an erroneous EPS lamp illumination. The customer may describe the Power Steering System Warning lamp is illuminated on the instrument cluster. Upon further inspection, the technician may find the following Diagnostic Trouble Code (DTC): C1214-87 Conf Data Code Request Message - Missing Message error set in the EPS control unit.

The customer may notice a false message displayed in the Cluster; Parking Sensors Unavailable and/or Sound System Unavailable.

The customer may notice a false message may be displayed on the radio; Audio & Parking Sensors Not Available.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

CUSTOMERS MAY COMPLAIN OF A MALFUNCTION INDICATOR LAMP ILLUMINATION. ALSO PROCEDURE FOR SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE *CN

ELECTRIC POWER STEERING MODULE NEEDS REPROGRAMMING WITH LATEST SOFTWARE TO CORRECT AN ERRONEOUS EPS LAMP ILLUMINATION *CN

Order the "R" part number for all orders:

this is normal and not a defect.

semi and full synthetic oils.

as a separate part number in the kit which is 04753095AB.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

The dealer may not be able to install the antenna mast to the antenna base. The mast may have the incorrect thread pitch (1.0 mm) and will not screw into the base. The mast should have a thread pitch of 0.8 mm.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

installed in the vehicle.

dress engines, but labeled as component engine 68275870AA or 71AA. The received engine will be configured for use with an automatic transmission, (includes auto transmission adapter plate / flexplate) or manual transmission. (includes flywheel / clutch asm) The received engine will be configured with or without a block heater. If required, dealer to purchase/install the block heater. The included instruction sheet K6855863AB in engine kit 68275870AA is to be followed for all applications that it applies. Please see the sheet for details. In addition to the items detailed in instruction sheet K6855863AB, please read the following below to determine the rework required to install this engine into a 2012- 2018 Fiat 500 (FF) with 1.4L EAB normally aspirated engine: 1) determine which condition exists for the received service engine a) vehicle has a manual transmission, received manual transmission engine. b) vehicle has a manual transmission, received automatic transmission engine. c) vehicle has an automatic transmission, received automatic transmission engine. d) vehicle has an automatic transmission, received manual transmission engine. 2) follow below steps based on condition (a) through (d) above. Condition a) No further rework required, other than ordering/installing a block heater if required. Condition b) Remove flexplate / auto trans adapter plate / auto trans engine mounting bracket / auto trans engine oil dipstick from new service engine. Transfer flywheel / clutch / manual trans engine mounting bracket / manual trans engine oil dipstick from old engine. Order/install block heater if required. Condition c) Identify the automatic transmission adapter plate on the original engine. Looking at the rear of the vehicle engine with adapter plate mounted:

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.

Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.

(ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P0171 - Fuel System 1/1 Lean ? P050D - Cold Start Rough Idle

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following transmission related conditions. ? Less than desired accelerator pedal response in Sport and TractionPlus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start.

(ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? U0402 - implausible data received from TCM ? P0133 - O2 sensor 1/1 slow response ? P0171 - Fuel System 1/1 Lean ? P050D - Cold Start Rough Idle In addition, customers may experience one or more of the following concerns: ? RPM flare at cold start. ? Less than desired idle performance. ? Cold engine RPM surge with gear engagement.

Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? P1DAD - Input Shaft-Output Shaft Direction Correlation ? U1424 - Implausible Engine Torque Signal Received In addition, the customer may also experience one or more of the following transmission related conditions: ? Less than desired 1-2 upshift on tip-in acceleration. ? Less than desired accelerator pedal response in Sport and TractionPlus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start.

Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? U1424 - Implausible Engine Torque Signal Received. In addition, the customer may also experience one or more of the following transmission related conditions: ? Garage Shifts (Shifting from Park or Neutral into Drive or Reverse.) ? Harsh 1-2 upshifts. ? Less than desired accelerator pedal response in Sport and TractionPlus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start.

(ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? U0402 - Implausible Data Received From TCM. ? P0133 - O2 Sensor 1/1 Slow Response. ? P0171 - Fuel System 1/1 Lean. ? P050D - Cold Start Rough Idle. In addition, customers may experience one or more of the following concerns: ? Clatter or ticking noise from the engine at idle. ? RPM flare at cold start. ? Less than desired idle performance. ? Cold engine RPM surge with gear engagement.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

IDLE COLD START, 02 SENSOR 1/1 SLOW RESPONSE AND WOULD NEED LATEST SOFTWARE PROGRAMMED TO ENGINE CONTROL MODULE (ECM). MODEL 2016 500X. *PE UPDATED 11/30/15 *CN

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.

Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0887-00 -Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P1CC9-00 - Unable to Engage Gear ? P1D98-00 - Incorrect Gear Ratio Clutch B or D Defective ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? U0401-00 - Implausible Data Received From The ECM-PCM

Module (TCM) with the latest available software. The customer may describe one or more of the following: ? Harsh 1-2 Upshift. ? Harsh Garage Shifts (Park to Reverse or Drive).

reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

MAY BE INDICATED *CN

PROCEDURE ON REPROGRAMMING THE DRIVETRAIN CONTROL MODULE WITH LATEST SOFTWARE *CN UPDATED 9/3/15.

SHIFTING *CN

REPROGRAMMING WITH LATEST SOFTWARE *CN UPDATED 12/3/15 *CN

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

may describe a clicking sound from the wheel?s plastic trim inserts when moving slowly or when stopped. The issue is heard on sunny days when the sun heats up the wheels and plastic inserts.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may notice when looking at the Kilometers ?(km) to service? that the value is set to 30,000 km. In LATAM it should be set at 15,000 km.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may notice when looking at the Kilometers ?(km) to service? that the value is set to 30,000 km. In LATAM it should be set at 15,000 km.

THE CUSTOMER MAY DESCRIBE A CLICKING SOUND FROM THE WHEELS PLASTIC TRIM INSERTS WHEN MOVING SLOWLY OR WHEN STOPPED. THE ISSUE IS HEARD ON SUNNY DAYS WHEN THE SUN HEATS UP THE WHEELS AND PLASTIC INSERTS."

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

CAUTION: Confirm the correct radio flash file to the applicable model and family vehicle before flashing. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. ? Charging schedule showing in the setting menu (FF BEV only). ? Korean language was not supported (APAC - Korea only). Enhancement: ? Removing the charging schedule from showing in the setting menu (FF BEV only). ? Adding Korean language support (APAC - Korea only).

CAUTION: Confirm the correct radio flash file to the applicable model and family vehicle before flashing. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. ? Charging schedule showing in the setting menu (FF BEV only). ? Korean language was not supported (APAC - Korea only). Enhancement: ? Removing the charging schedule from showing in the setting menu (FF BEV only). ? Adding Korean language support (APAC - Korea only).

(IPC) with the latest available software. The customers may notice that the IPC brightness level may not adjust correctly to correspond with the outside light levels. Also an enhancement was made to properly calculate and display when the next service maintenance is needed.

DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.

brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: ? Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. ? Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.

brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: ? Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. ? Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.

brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: ? Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. ? Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.

The customer may experience one or more of the following: ? Travel Link soft key missing (U.S. only). ? Weather map now available for SXM (U.S. only). ? Cannot select different map displays. ? Point Of Interest (POI) cannot be added as waypoints. ? Conference calls may not display all active callers. ? Improve iPod response time, to start playing audio. ? Browsing knob inoperative after exiting Short Message Service (SMS). ? ?Where Am I? feature inoperative while driving. ? When using iPod touch, the incorrect song name may be displayed. ? May not display Auto Park Brake menu, if equipped. ? Cannot create a new SMS, using phone numbers. ? Display the correct message, when in service mode. ? Poor or no audio from the radio, also radio controls may not respond. On further inspection the technician my find DTC B223B-00 Vehicle Configuration Mismatch. ? False error message while in service brake mode. ? Personal setting lost after key cycle, dynamic guidelines and Show Time bar. IMPROVEMENTS ? Display Travel Link soft key on more of the display screens (U.S. only). ? Display the correct media screen when using iPod touch. ? Improve screen layouts during media playback. ? Improved SMS screen displays. ? Correctly display speed lockout messages. ? Color improvements on navigation map. ? Improved chime warning volumes. ? Browsing improvements for Bluetooth audio. ? Improved conference call handling. ? Improved Voice Recognition (VR) commands for AM radio request.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Print I-Sheet for technician use.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Library for specifications so a suitable alternative can be used

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

center instrument panel bezel are sticking.

B)

shims.

REPROGRAMMING INSTRUMENT CLUSTER WITH LATEST SOFTWARE *CN