2005 Dodge Ram 3500 TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

This applies to Cummins 5.9L and 6.7L engines only.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

MALFUNCTION INDICATOR LAMP ILLUMINATION WITH DIAGNOSTIC TROUBLE CODES P0330, AND/OR P0740. *TT

*TT

*TT

WARRANTY PLANNING & ADMINISTRATION *TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

*TT

THIS CAN CAUSE THE ON BOARD DIAGNOSTIC (OBD) FUEL SYSTEM MONITOR TO MALFUNCTION. EMISSIONS RECALL D46. *TT

*TT *MJ THIS BULLETIN SUPERSEDES BULLETIN 18-006-04A DATED 04/06/2004. *TT

required to attach Neutral Start Switch

*KB

*TT

*TT

MODEL YRS FOR CAB CHASSIS (REG AND MEGA PICKUPS AND 4X4) 2003-2011. *PE

*TT

*TT

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

FLASH. *TT