2005 Dodge Ram 2500 TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

This applies to Cummins 5.9L and 6.7L engines only.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

*TT

*TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*TT

SUN VISORS WHICH DO NOT MEET SPECIFICATIONS. THIS COULD LEAD TO LOOSE OR RATTING VISORS. *SC

required to attach Neutral Start Switch

The Customer communication requested return of unsold inventory to inspect for improperly crimped hose fittings. Improperly crimped hose fittings could cause a potential fluid leak at the crimp.

The Customer communication requested return of unsold inventory to inspect the hose end fittings. Parts will be inspected for incorrectly threaded fittings causing inability to complete assembly of the oil cooler line to the vehicle.

inner tie rod assembly at the pitman arm on a vehicle built before Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~ If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available:~ 68038055AA Outer end Tie Rod Package~ 68034233AA Tie Rod Adjuster Tube~ 68038054AA Inner end Tie Rod Package~ 68036726AB Drag Link Outer Socket Package~ 68034229AA Drag Link Adjuster Tube~ 68036940AA Drag Link Inner Socket Package~ You can go to the 2008 MY for graphically representation of parts. Issue 3: Some vehicles have been updated with the Big Steering Gear Kit. The Big Steering gear is identified by a 6 bolt top cap and replaces the 4 bolt top cap unit. The Big Steering Gear uses Pitman Arm 68141515AA and DOES NOT use 68039930AA. Ensure Tie Rod alignment procedure is used for proper setup and at vehicle alignment.

required to attach Neutral Start Switch

*KB

*TT

*SC

*SC

THE DRAIN PLUG MAY NOT HAVE BEEN TIGHTENED TO SPECIFICATIONS. *SC

*TT

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.

Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available.

MODEL YRS FOR CAB CHASSIS (REG AND MEGA PICKUPS AND 4X4) 2003-2011. *PE

*TT

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*TT UPDATE. *TT

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

EMISSIONS RECALL E21 TO REPLACED PCM/VECI LABEL. *TT

*RM

2005 RAM TRUCK A/C EVAPORATOR DRAIN TUBE PLUGGED. *SC

*SC

2005 RAM TRUCK POWER WAGON LOWER CONTROL ARM POPPING SOUND. *SC