2007 Dodge Ram 1500 TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.

This applies to Cummins 5.9L and 6.7L engines only.

The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.

available as part of the standard diagnostic process located in TechCONNECT>Service Info.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

This new fill tube incorporates a check valve. Some customers may experience a fuel spit back condition during vehicle refueling.

There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

different injectors for the 6.7L Cummins Turbo Diesel depending on application and they are not interchangeable! Using the wrong injector may seriously affect engine operation. The proper usages are as follows:~ For DH/D1 (Ram 2500/3500 pickup - with a factory bed) the P/N is: 68027067AA~ For DC/DM (Ram 3500/4500/5500 Chassis Cabs) the P/N is: 68002012AB

Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~

05072138AA as a service part but built with different mating wiring connector (round) - also order connector repair kit 05019958AA (square).~ 2007MY RAM Trucks equipped with 6.7L Cummins turbo diesel engine only: If the A/C pressure transducer requires replacement, use part number 05072138AA that has a rectangular shaped electrical connector. If the engine wiring harness has a circular wiring connector, use jumper harness 68028774AA to change it to a rectangular connector.~ 6.7L RAM trucks built before10/17/2006 has pressures transducers (p/n 05191766AA) with a round connector that should have been changed per RRT 06- 068 to a rectangular transducer.~ 2001-2008 KJ, K1, ND.~

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

MODEL 2007-2008 RAM 1500. *PE

THE PRAETORIAN CONTROL(PCM) ON CERTAIN VEHICLES MAY NOT BE ABLE TO DETECT A COMPLETELY BLOCKED EGR VALVE OR PASSAGE MAY CAUSE THE ENGINE TO EMIT NITROGEN OXIDES AT LEVELS WHICH MAY EXCEED CALIFORNIA EMISSIONS STANDARDS. CSC LETTER WAS RECEIVED. *PE

*NJ

*KB

*KB

*KB

APPLIES TO VEHICLES EQUIPPED WITH A 5.9L CUMMINS 24-VALVE DIESEL ENGINE. *KB

*TT

If no response in 15 minutes, proceed with repair.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*KB

*TT

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

*KB

*KB

*KB

*KB

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*NJ

*NJ

TOTALLY INTEGRATED POWER MODULE (TIPM) WAS INADVERTANTLY PROGRAMMED WITH SOFTWARE THAT MAY PREVENT THE TRANSMISSION FROM SHIFTING PROPERLY. *KB

*KB

*KB UPDATED 08-13-07. *KB UPDATED 01/09/08. *NJ UPDATED 3/7/08. *NJ

Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available.

MODEL YRS FOR CAB CHASSIS (REG AND MEGA PICKUPS AND 4X4) 2003-2011. *PE

*PE

*LJ

*NJ

*KB

*KB

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.

*KB