2003 Dodge Ram 1500 TSBs

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*TT

*EH

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

This applies to Cummins 5.9L and 6.7L engines only.

valve insulator, attaching rivet and instruction sheet are now available as a kit. If the insulator requires replacement please order kit 68253161AA. Insulator only used on Auto-RWD transmission Note: The color of the insulator is not relevant for service.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~

ADVANCED SERVICE INFORMATION #05-002. *TT

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available.

*PE

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

inner tie rod assembly at the pitman arm on a vehicle built before Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~ If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available:~ 68038055AA Outer end Tie Rod Package~ 68034233AA Tie Rod Adjuster Tube~ 68038054AA Inner end Tie Rod Package~ 68036726AB Drag Link Outer Socket Package~ 68034229AA Drag Link Adjuster Tube~ 68036940AA Drag Link Inner Socket Package~ You can go to the 2008 MY for graphically representation of parts. Issue 3: Some vehicles have been updated with the Big Steering Gear Kit. The Big Steering gear is identified by a 6 bolt top cap and replaces the 4 bolt top cap unit. The Big Steering Gear uses Pitman Arm 68141515AA and DOES NOT use 68039930AA. Ensure Tie Rod alignment procedure is used for proper setup and at vehicle alignment.