Powered byNHTSA|EPA|Community Reports
HomeTSBsDodge2007 Nitro

2007 Dodge Nitro TSBs

62 Technical Service Bulletins across 10 categories

Engine

24 bulletins
11023612

SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH

10229181

Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications.

Read full bulletin

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

10223854

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four...

Read full bulletin

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

10223602

Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications.

Read full bulletin

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

10223599

Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications.

Read full bulletin

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

10221097

Transmission Kit with Torque Converter 1.

Read full bulletin

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

10220843

NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment.

Read full bulletin

If the pins are missing request to add the dowel pin first and then install the transmission

10216395

Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus...

Read full bulletin

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

10216269

Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves...

Read full bulletin

replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.

10191460

Valve Body. These may cause over drive cycling.

10190590

NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment.

Read full bulletin

If the pins are missing request to add the dowel pin first and then install the transmission

10171324

This SKU is a Power Window Regulator and Motor Assembly.

Read full bulletin

The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.

10171323

This SKU is a Power Window Regulator and Motor Assembly.

Read full bulletin

The customer communication requested return of unsold inventory to inspect the geometry of the part. There is a feature on the assembly that is intended to provide clearance to the door handle, it may not provide enough clearance which could prevent the door handle from being installed.

10140065

Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus...

Read full bulletin

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

10138987

Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus...

Read full bulletin

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

10136479

Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves...

Read full bulletin

replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.

10128983

Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves...

Read full bulletin

replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.

10128948

Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus...

Read full bulletin

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

10121927

NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar...

Read full bulletin

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

10052148

JEEP: ON SOME JEEPS, WHEN REFUELING, THE FUEL WILL SPIT BACK DUE TO INLET HECK VALVE AND INFORMATION IS PROVIDED...

Read full bulletin

REGARDING REPLACING FUEL TANK WITH NEW PART. MODELS 2008 LIBERTY, 2007-2008 NITRO. *PE

10030707

JEEP: IN COLD CLIMATES A MIL ILLUMINATION P0123 OR P0222 OR STORED DIAGNOSTIC TROUBLE CODE P0123 OR 00222 AND THE ETC LIGHT ILLUMINATED.

Read full bulletin

THIS INVOLVES REPLACING THE ELECTRONIC THROTTLE BODY AND CLEAN AIR DUCT. *PE

10024966

NO ENGINE CRANK OR NO ENGINE START DUE TO ELECTRONIC LOCKUP OF THE WCM/SKREEM.

Read full bulletin

*NJ

10024056

FLASH: ROUGH IDLE AND DROP IN ENGINE SPEED UPON GEAR ENGAGEMENT AFTER COLD START.

Read full bulletin

*NJ

10021422

INTAKE - TO - THROTTLE BODY JOINT MAY CAUSE A WHISTLE - LIKE SOUND ON 3.7L ENGINES.

Read full bulletin

*KB

Electrical

8 bulletins
10248509

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website...

Read full bulletin

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

10244348

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website...

Read full bulletin

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

10221831

(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns

10180221

(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns

10175735

Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test...

Read full bulletin

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

10023661

EMISSIONS RECALL G45--VECI LABEL - AN INCORRECT VEHICLE EMISSION CONTROL INFORMATION (VECI) LABEL WAS INSTALLED ON ABOUT TEN THOUSAND VEHICLES.

Read full bulletin

THE ORIGINALLY INSTALLED VECI LABEL DOES NOT DISPLAY THE CORRECT SPARK PLUG INFORMATION. *NJ

10021984

STEERING ANGLE SENSOR - NOT INITIALIZED/INTERNAL.

Read full bulletin

*KB

10021239

POWERTRAIN CONTROL MODULE INITIALIZATION.

Read full bulletin

*KB

Other

8 bulletins
10220471

Mechanical rocker arm, intake, 1.7 ratio.

10220101

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry...

Read full bulletin

awareness regarding the use of aftermarket parts.

10220097

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to...

Read full bulletin

structural repair parts usage.

10191442

Mechanical rocker arm, intake, 1.7 ratio.

10175743

Disinfectant Solution Recommended for COVID-19

10169249

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry...

Read full bulletin

awareness regarding the use of aftermarket parts.

10169245

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to...

Read full bulletin

structural repair parts usage.

10129008

82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states ...

Read full bulletin

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Air Bags & Safety

6 bulletins
10220576

SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions

10204370

Customer Satisfaction Notification Y22 Driver Airbag Emblem

10204368

Customer Satisfaction Notification Y22 Driver Airbag Emblem

10188780

SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions

10139978

Restraints Remove I-Sheet from packaging.

Read full bulletin

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

10021599

PASSENGER AIR BAG DEACTIVATION.

Read full bulletin

*KB

Transmission

6 bulletins
10215825

Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially...

Read full bulletin

separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.

10188658

Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially...

Read full bulletin

separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.

10034229

JEEP: MANUAL TRANSMISSION POPS OUT OF GEAR.

Read full bulletin

THE TRANSMISSION POPS OUT OF FIRST GEAR WHILE ACCELERATING. THE CONDITION, MAY OCCUR INTERMITTENTLY AND MAY BE DIFFICULT TO DIAGNOSE. VERIFY THAT THE SHIFT BOOT IS NOT CAUSING THE ISSUE BY ENSURING THE BOOT IS NOT BINDING WHEN IN FIRST GEAR. *PE

10022416

MIL ILLUMINATION WITH DIAGNOSTIC TROUBLE CODE P0741- TORQUE CONVERTER CLUTCH CIRCUIT PERFORMANCE.

Read full bulletin

*KB

10021089

TORQUE CONVERTER SHUDDER / SHIFT QUALITY IMPROVEMENTS / DTC P0732.

Read full bulletin

*KB UPDATED 08-13-07. *KB UPDATED 01/09/08. *NJ UPDATED 3/7/08. *NJ

10020747

VEHICLE SURGE/DRONE DURING TORQUE CONVERTOR LOCKUP AND/OR 1-2 PART THROTTLE SHIFT QUALITY.

Read full bulletin

REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) WITH NEW SOFTWARE. *KB

Lighting

3 bulletins
10220099

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair...

Read full bulletin

industry awareness regarding the use of recycled or salvage parts.

10169247

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair...

Read full bulletin

industry awareness regarding the use of recycled or salvage parts.

10023351

EXTERIOR LAMP - LENS FOGGING.

Read full bulletin

*NJ

Infotainment

2 bulletins
10025382

CHRYSLER\DODGE\JEEP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER.

Read full bulletin

CUSTOMER SATISFACTION NOTIFICATION H11; RADIO SOFTWARE UPDATE. THIS NOTIFICATION APPLIES ONLY TO VEHICLES EQUIPPED WITH A MYGIG RADIO (SALES CODE RER WITH NAVIGATION SYSTEM OR REN WITHOUT NAVIGATION SYSTEM). CSC WAS RECEIVED. *PE

10024945

DVD SOFTWARE UPDATE MYGIG RADIO FOR MANY RADIO FUNCTIONAL ISSUES AND IMPROVEMENTS.

Read full bulletin

*NJ

Tires & Wheels

2 bulletins
10022002

CHROME CLAD WHEEL CRACK.

Read full bulletin

*KB

10021247

TIRE PRESSURE MONITOR SYSTEM INFORMATION.

Read full bulletin

*KB

Body & Paint

2 bulletins
10021248

CRACKED WINDSHIELD DUE TO BEING HIT BY A FOREIGN OBJECT LIKE A STONE.

Read full bulletin

*KB

10020959

REAR DOOR INSIDE AND OUTSIDE HANDLES DO NOT FUNCTION.

Read full bulletin

*KB UPDATED 01/09/08. *NJ

Steering

1 bulletin
10023393

SLIGHT PLAY IN STEERING/STIFF/CHOPPY/BUMPY RIDE.

Read full bulletin

*NJ