2017 Dodge Journey TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

Sensor Circuit Performance

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

(PCM) with the latest available software.This bulletin applies to vehicles within the following markets/countries: NAFTA. Customers may also notice one or more of the following symptoms:When coming to a stop or making a turn, the vehicle suddenly shuts off. Mostly noted in high ambient conditions greater than 40 C (105 F). A hesitation/surge feel that some customers might note it feels like misfire at 65-110 kph (40-70 mph) in 4th gear lock up. In addition, the following software enhancement is available:Start Improvements for cold or high altitude starts when using E15 fuel.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

If you cannot reach Jian please provide the freeze frame data to Jian in a email to jian.zhu@fcagroup.com. If no response in 15 minutes, proceed with repair by replacing the solenoid and the harness.

P0073 fault codes, please call Omar Jobe at cell (248) 910-2166. If you do not receive a response within 15 minutes, please proceed with repair. Digital images of any physical issue discovered would be very helpful. Please send digital images to email address: omar.jobe@fcagroup.com.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

thomas.a.sharp@external.fcagroup.com prior to replacing the fan module on this vehicle. If no answer and if you do not receive a return call within 15 minutes, please continue with the normal repair.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

The customer may describe the headlamps flicker while operating at night. This condition may be more prevalentafter the bulb(s) have been replaced with an aftermarket bulb.

The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPodtouch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter

this is normal and not a defect.

semi and full synthetic oils.

If you cannot reach Jian please provide the freeze frame data to Jian in a email to jian.zhu@fcagroup.com. If no response in 15 minutes, proceed with repair.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

take photos of the condition and/ or issue with seat cable before disassembly, Please email pictures of cable including part number to FCA Redacted Content; please include dealer contact information for follow up. If no response in 15 minutes, proceed with repair.

Before replacing this part send an email to FCA Redacted Content; With the dealer address and a picture of the part. If no response in 15 minutes, proceed with repair.

Before replacing this part send an email to FCA Redacted Content; With the dealer address and a picture of the part. If no response in 15 minutes, proceed with repair.

Before replacing this part send an email to FCA Redacted Content; With the dealer address and a picture of the part. If no response in 15 minutes, proceed with repair.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

contact: Marco Rodriguez at (248) 941-8623 prior to replacing the component. If you do not receive a response within 15 minutes, please continue with normal repair procedure.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

plastic panels and applying corrosion protection.

Customers may experience wet carpet from water intrusion when fording through deep water due to a missing underbody hole plug.

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

Avenger/Chrysler 200 (JS)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

Avenger/Chrysler 200 (JS)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

Avenger/Chrysler 200 (JS)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

622-8109 before performing repair service. If you do not receive a response within 15 minutes, please continue with the normal repair procedure.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

on about 5,800 of the above vehicles may not function in the ?Accessibility Mode? if enabled. The Federal Communications Commission (FCC) requires video description accessibility, which enables blind or sight-impaired passengers to enjoy video entertainment in video systems. Reprogram audio files in the radio.

A customer may experience no audible read-back when read-back option is enabled.

A customer may experience no audible read-back when read-back option is enabled.

A customer may experience no audible read-back when read-back option is enabled.

A customer may experience no audible read-back when read-back option is enabled.

If no response in 15 minutes, proceed with the repair.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)

are in need of solenoid and harnesses for analysis. Please repair the vehicle by replacing the solenoid (PN# 5140429AA) and the transmission harness (PN# 68080261AF) without disconnecting the two components at the solenoid connection. Contact Bruce Schmoock at (248) 512-0289 and supply the last 8 of the VIN, the RO number and dealer code so a FasTrack can be generated for the two components.

are in need of solenoid and harnesses for analysis. Please repair the vehicle by replacing the solenoid (PN# 5140429AA) and the transmission harness (PN# 68080261AF) without disconnecting the two components at the solenoid connection. Contact Bruce Schmoock at (248) 512-0289 and supply the last 8 of the VIN, the RO number and dealer code so a FasTrack can be generated for the two components.

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS Part Number 06511385A$ ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts 8 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only shot peened

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

B)

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

organizer; latches are serviceable separately. You do not need to replace the entire bin or lid for this, the following part numbers are for the cover latches: 1CB78DK7AA 1CB78XDVAA Failure to follow this could result in a dealer chargeback