2012 Dodge Grand Caravan TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

stays awake resulting in a continuous electrical draw. The customer may experience a dead battery.

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

reprogramming the HVAC Module with new software. Customers may experience the following condition: ? HVAC system intermittently blows cold regardless of blend door/temperature setting. Updating the HVAC software will correct this condition.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

window, if requested by the customer. A customer may inquire about Safety Recall P25 and request to have their Power Quarter Vented Window Switch disconnected or a customer may have noticed a burning odor or have seen smoke coming from the power vented window switch on the drivers door. Once the proper amount of parts are available, all of the customer will be notified. In the meantime, the switch can be disconnected, to satisfy the customer.

power vent window, if requested by the customer. A customer may inquire about Safety Recall P25 and request to have their Power Quarter Vented Window Switch disconnected or a customer may have noticed a burning odor or have seen smoke coming from the power vented window switch on the drivers door. Once the proper amount of parts are available, all of the customer will be notified. In the meantime, the switch can be disconnected, to satisfy the customer.

the Instrument Panel Cluster (IPC). A customer may note that some of the translation for French and Spanish is incorrect in the Electronic Vehicle Information Center (EVIC) when trying to change Personal Settings for park assist. All park assist functions will operate properly.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

the Amplifier with updated software. The customer may experience audio distortion from the front door speakers when the rear AUX port is in use. The distortion may occurs when playing certain media with a lot of high frequency content. The equalization doesn't have a settings for rear AUX mode and defaulted to the AM mode. The AM mode equalization has a boost for high frequencies. This increase boost can cause the Amp to distort the sound.

the Amplifier with updated software. The customer may experience audio distortion from the front door speakers when the rear AUX port is in use. The distortion may occurs when playing certain media with a lot of high frequency content. The equalization doesn't have a settings for rear AUX mode and defaulted to the AM mode. The AM mode equalization has a boost for high frequencies. This increase boost can cause the Amp to distort the sound.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

the Amplifier with updated software. The customer may experience audio distortion from the front door speakers when the rear AUX port is in use. The distortion may occurs when playing certain media with a lot of high frequency content. The equalization doesn't have a settings for rear AUX mode and defaulted to the AM mode. The AM mode equalization has a boost for high frequencies. This increase boost can cause the Amp to distort the sound.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS Part Number 06511385A$ ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts 8 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only shot peened

DUE TO SOFTWARE PROGRAMMING CAUSING POOR AUTOMATIC TRANSAXLE SHIFT PROBLEMS, A NEW PCM SOFTWARE IS AVAILABLE TO IMPROVE SHIFT QUALITY OF AUTOMATIC TRANSAXLE. MODEL 2011-2013 GRAND CARAVAN, TOWN AND COUNTRY. *PE

Library for specifications so a suitable alternative can be used

of regular maintenance

A Superseded By Customer Satisfaction Notification (CSN) P25 Refer to service procedures outlined in CSN P25.

A Superseded By Customer Satisfaction Notification (CSN) P25 Refer to service procedures outlined in CSN P25.

A Superseded By Customer Satisfaction Notification (CSN) P25 Refer to service procedures outlined in CSN P25.

B)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed