2016 Dodge Durango TSBs

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."

for replacement as a remedy for fluid leak.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

The customer may describe that their vehicle has oil weepage.

variable valve timing solenoids due to multiple DTCs. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or the engine runs rough. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: P0017 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 2. P0019 - Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor 2. P000A - Bank 1 Camshaft 1 Position Slow Response. P000C - Bank 2 Camshaft 1 Position Slow Response.

Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(2017 MY with a 3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L 2017 MY Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle driveability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.

above vehicles has software that may be operating the Exhaust Gas Recirculation valve (EGR) with an aggressive seating velocity. An aggressive seating velocity may damage the EGR valve. As a result this condition may illuminate the Malfunction Indicator Lamp (MIL) and display a P0404 code. The PCM must be reprogrammed on all involved vehicles.

installed in the vehicle.

and Active diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ As part of normal diagnostics tool # 9936 TPM-RKE Analyzer can be used to wirelessly retrieve TPM sensor data and aid you in diagnosing. The tool filters data by year and body style. Be sure to update the tool to Software Version 16.01 and check for updates periodically. Vehicles and new TPM info is added several times a year. Updates are available through TechCONNECT home page; Service Tools & Equipment; Tire Pressure Monitor Tool; Software Downloads. ~ Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313 or Brian Malski on cell (248) 892-1514. If no response within 15 minutes, proceed with repair.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The customer may describe that their vehicle has oil weepage.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

and Active diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ As part of normal diagnostics tool # 9936 TPM-RKE Analyzer can be used to wirelessly retrieve TPM sensor data and aid you in diagnosing. The tool filters data by year and body style. Be sure to update the tool to Software Version 16.01 and check for updates periodically. Vehicles and new TPM info is added several times a year. Updates are available through TechCONNECT home page; Service Tools & Equipment; Tire Pressure Monitor Tool; Software Downloads. Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313 or Brian Malski on cell (248) 892-1514. If no response within 15 minutes, proceed with repair.

diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair. ~_________________________________________________________________

program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.

C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacement part will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Bruce Cartwright CELL (586) 306-8899~ Ayed Hadaad CELL (248) 941-8707~ Patrick Walster CELL (248) 890-3561~ Issue 1:~ 2016 WK - Auto Stop/Start complaints affecting Integrated Center Stacks (ICS)~ Chrysler engineering is requesting to review in-person a 2016 WK before it is disturbed with the above-mentioned complaint (anywhere in SouthEast Michigan).~ The issue in question is Auto Stop/Start disable ? PCM - Switch Correlation Fault Code B23C3~ We need the vehicle to remain undisturbed so that the team can perform progressive disassembly and determine if there is an impact of the ICS to I/P mounting on this issue.~ Issue 2:~ On a 2016MY WK (Grand Cherokee) and WD (Durango), the Integrated Center Stack (ICS) may experience a lock-up condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P06EF - Engine Restart Performance(3.0L and 3.6L Only). P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one or more of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle drivability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

verify that there are no steel dowel pins pressed into the cylinder head. If dowels are present in the cylinder head please remove carefully without touching/damaging the cylinder head sealing surface.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.

Pentastar engine (ERC)~ Prior to replacing a component due to any of the following DTCs - P0401, P040B, P2457, P04D0, P04D1, P04D2, or P04CE please contact Omar Jobe at Cell (248) 910-2166.~ If a response is not received within 30 minutes, then proceed with the necessary repair.

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Bruce Cartwright CELL (586) 306-8899~ Ayed Hadaad CELL (248) 941-8707~ Patrick Walster CELL (248) 890-3561~ Issue 1:~ 2016 WK - Auto Stop/Start complaints affecting Integrated Center Stacks (ICS)~ Chrysler engineering is requesting to review in-person a 2016 WK before it is disturbed with the above-mentioned complaint (anywhere in SouthEast Michigan).~ The issue in question is Auto Stop/Start disable ? PCM - Switch Correlation Fault Code B23C3~ We need the vehicle to remain undisturbed so that the team can perform progressive disassembly and determine if there is an impact of the ICS to I/P mounting on this issue.~ Issue 2:~ On a 2016MY WK (Grand Cherokee) and WD (Durango), the Integrated Center Stack (ICS) may experience a lock-up condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

and Active diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ As part of normal diagnostics tool # 9936 TPM-RKE Analyzer can be used to wirelessly retrieve TPM sensor data and aid you in diagnosing. The tool filters data by year and body style. Be sure to update the tool to Software Version 16.01 and check for updates periodically. Vehicles and new TPM info is added several times a year. Updates are available through TechCONNECT home page; Service Tools & Equipment; Tire Pressure Monitor Tool; Software Downloads. Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313 or Brian Malski on cell (248) 892-1514. If no response within 15 minutes, proceed with repair.

To announce a Fast Feedback Program to replacing or repairing 3.6L V6 24V VVT Engine (Sales code ERC) in an effort to collect, monitor and correct quality issues in a timely and efficient matter.

MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.

The customer may describe that their vehicle has oil weepage.

diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair. ~_________________________________________________________________

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.

C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacementpart will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory: P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Other enhancements included in this update: Improved knock sensor performance.

release engineer Majdi Yaqub at cell (248) 763-5747. If no response within 15 minutes, proceed with repair.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

variable valve timing solenoids due to multiple DTCs. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or the engine runs rough. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: P0017 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 2. P0019 - Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor 2. P000A - Bank 1 Camshaft 1 Position Slow Response. P000C - Bank 2 Camshaft 1 Position Slow Response.

and Active diagnostic trouble codes C1501-31, C1502-31, C1503-31, C1504-31. 2015 & 2016 TPM Sensors ARE NOT interchangeable.~ As part of normal diagnostics tool # 9936 TPM-RKE Analyzer can be used to wirelessly retrieve TPM sensor data and aid you in diagnosing. The tool filters data by year and body style. Be sure to update the tool to Software Version 16.01 and check for updates periodically. Vehicles and new TPM info is added several times a year. Updates are available through TechCONNECT home page; Service Tools & Equipment; Tire Pressure Monitor Tool; Software Downloads. ~ Prior to replacing any components on MY16 WK/WD vehicles, please contact Raja Charabuddi on cell (248) 202-7313 or Brian Malski on cell (248) 892-1514. If no response within 15 minutes, proceed with repair.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.

The customer may describe one or more of the following symptom/conditions:The headlamps flicker while operating at night. This condition may bemore prevalent after the bulb(s) have been replaced with an aftermarket bulb. Customers with Diesel engine equipped vehicles may experience cancelled remotestart request during winter months.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle drivability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

either: Ron Dallison cell: (248) 292-9510 ron.dallison@fcagroup.com Chris Riddick cell: (248) 434-3628 chris.riddick@fcagroup.com Joe Lovell cell: (734) 309-6467 joe.lovell@fcagroup.com Engineering is seeking audio recordings of the concern in an effort to root cause and make necessary improvements to future pumps. Please email any audio recording or documentation of when/where/how the pump, or Idler Pulley makes noise to the above emails. If the dealer is located in the Detroit Metro Area, Engineering may send a representative to review with technician. Any information is appreciated. If a response is not received within 15 mins , then proceed with the necessary repair.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: P000A/P000C - Camshaft Slow To Respond. P0300 - Multiple Cylinder Misfire.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

The customer may describe that their vehicle has oil weepage.

MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DTCS SET IN THE PCM MEMORY: **B23C3 - STOP/START DISABLE SWITCH 1/2 CORRELATION (3.0L AND 3.6L ONLY). P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT (5.7L ONLY).** P2299-00 - BRAKE PEDAL POSITION/ACCELERATOR PEDAL POSITION INCOMPATIBLE. OTHER ENHANCEMENTS INCLUDED IN THIS UPDATE: IMPROVED KNOCK SENSOR PERFORMANCE."

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory: P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Other enhancements included in this update: Improved knock sensor performance.

A). TO ANNOUNCE A FAST FEEDBACK PROGRAM FOR REPLACING OR REPAIRING THE 3.6L V6 24V VVT ENGINE (SALES CODE ERC) IN AN EFFORT TO COLLECT, MONITOR AND CORRECT QUALITY ISSUES IN A TIMELY AND EFFICIENT MATTER.

PROGRAM FOR REPLACING OR REPAIRING THE 3.6L V6 24V VVT ENGINE (SALES CODE ERC) IN AN EFFORT TO COLLECT, MONITOR AND CORRECT QUALITY ISSUES IN A TIMELY AND EFFICIENT MATTER.

SYMPTOM/CONDITION: A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory: P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Other enhancements included in this update: Improved knock sensor performance.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Customers may experience one or more of the following: Satellite radio reception improvements. Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. (U.S. Market Only) (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle. (U.S. Market Only)

Tire Pressure Sensors Values Are Not Displayed

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Customers may experience one or more of the following:?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. HVAC temperature out of sync with radio display (KL vehicles). Improvements:Adds Apple Siri Eyes Free capability for iPhone owners. Add the ability to drag and drop icons into the menu bar. Enhanced Voice Recognition (VR) performance. Media devices, phone pairing, and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature. Satellite radio reception improvements.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

updating the Comfort Seat and Wheel Module (CSWM) software for the KL/UF vehicles or the Heated Seat Module (HSM) software for the W3/WK/WD/LD/LA & LX vehicles. A customer may describe that the heated steering wheel shuts off to soon, usually after 30 seconds and does not achieve satisfactory temperature. This is an intermittent condition and more noticeable at temps below 19.5C (67.1F).

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Customers may experience one or more of the following:?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. HVAC temperature out of sync with radio display (KL vehicles). Improvements:Adds Apple Siri Eyes Free capability for iPhone owners. Add the ability to drag and drop icons into the menu bar. Enhanced Voice Recognition (VR) performance. Media devices, phone pairing, and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature. Satellite radio reception improvements.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

half shaft due to grease leaking from the boot. The customer or technician may find grease leaking out of the left front axle half shaft inner boot.

half shaft due to grease leaking from the boot. The customer or technician may find grease leaking out of the left front axle half shaft inner boot.

to replace the load floor assembly for a replacement load floor handle

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

There is a potential for water intrusion which over time could lead to an inoperable license plate lamp. Customers may comment on one or more of the following: ? License plate LED light is inoperable. ? Moisture in the license plate lamp housing. This bulletin involves inspecting the license plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a additional O-ring and foam gasket to the license plate applique

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

poor fit at top edge, side and bottom please call Dan Jovan on cell: (248) 760-4348.~ If no response within 15 minutes, please continue with diagnostics/repair.~

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

The Latch is now released for service under part number 68599540A$.

poor fit at top edge, side and bottom please call Dan Jovan on cell: (248) 760-4348.~ If no response within 15 minutes, please continue with diagnostics/repair.~

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

Customers may comment on the following:Rattle coming from sunroof.

Sunroof Drain Tube Inspection.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Liftgate Will Not Power Open.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

excessive effort needed to open and close the lid. Customers may describe excessive effort is required to open and close the cargo load lid. The cargo load floor lid may have excessive effort (more than 15 lbs of force) when opening and closing due to interference between the rear edge of the cargo floor load lid and the tailgate scuff plate.

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

D)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: U0404 - Invalid Data Received From Gear Shift Control Module "A". In addition, customers may experience the following conditions: Bumps on 2 - 1 down-shift while braking. The M on the shifter and Instrument cluster may be blinking. The following improvements are included in this update: **Improved 2 - 1, 3 - 2 and 6 - 5 down-shifts (6.4L only).** Improved 1 - 2 light throttle up-shifts.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: U0404 - Invalid Data Received From Gear Shift Control Module "A". In addition, customers may experience the following conditions: Bumps on 2 - 1 down-shift while braking. The M on the shifter and Instrument cluster may be blinking. The following improvements are included in this update: **Improved 2 - 1, 3 - 2 and 6 - 5 down-shifts (6.4L only).** Improved 1 - 2 light throttle up-shifts.

Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: U0404 - Invalid Data Received From Gear Shift Control Module "A". In addition, some customers may experience the following conditions: **Bumps on 2 -1 down-shift while braking.** The M on the shifter and Instrument cluster may be blinking. The following improvements are included in this update: **Improved 1 - 2 light throttle up-shifts.**

cell (734) 626-3120, or Todd cell (810) 252-9714 . If response if not received within 15 minutes, then proceed with necessary repair."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

18.01.35 (BU Vehicles)

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

If no response in 15 minutes, please continue with repair

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

If no response in 15 minutes, please continue with repair

need to be replaced with updated components if front park/turn signal bulb is inoperative.

plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a foam gasket to the license plate applique. Customers may comment on one or more of the following: License plate LED light is inoperable. Moisture in the license plate lamp housing.

Intermittently, Crank No Start, Vehicle Will Not Restart After ESS Stop

industry awareness regarding the use of recycled or salvage parts.

plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a foam gasket to the license plate applique. Customers may comment on one or more of the following: License plate LED light is inoperable. Moisture in the license plate lamp housing.

Intermittently, Crank No Start, Vehicle Will Not Restart After ESS Stop

industry awareness regarding the use of recycled or salvage parts.

A small number of vehicles may have mismapped Diagnostic Trouble Codes (DTCs) below pointing to the wrong modules with no Malfunction Indicator Lamp (MIL) illumination: NOTE: This update should be performed to reduce the potential for misdiagnosis of related systems and incorrect module replacement. U0100-00 - Lost Communication With ECM/PCM. U0140-00 - Lost Communication With Body Control Module. U0101-00 - Lost Communication With TCM. U0402-00 - Implausible Data Received From TCM.

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

A small number of vehicles may have mismapped Diagnostic Trouble Codes (DTCs) below pointing to the wrong modules with no Malfunction Indicator Lamp (MIL) illumination: NOTE: This update should be performed to reduce the potential for misdiagnosis of related systems and incorrect module replacement. U0100-00 - Lost Communication With ECM/PCM. U0140-00 - Lost Communication With Body Control Module. U0101-00 - Lost Communication With TCM. U0402-00 - Implausible Data Received From TCM.

If you are unable to get a response within 15 minutes, please take a picture that shows the sensor side together with the plunger and continue with normal repair procedure.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

B)

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

Information Center (EVIC) Switch due to heated steering wheel shutting off too soon. A customer may describe that the heated steering wheel shuts off to soon, usually after 30 seconds and does not achieve satisfactory temperature. This is an intermittent condition and more noticeable at temperatures below 19.5C (67.1F).

technician an overview of the steps a customer will need to take to complete the update.