2014 Dodge Durango TSBs

for replacement as a remedy for fluid leak.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles e

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle: 2015 WK 3.0L engine (Sales Code EHD) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start. 2015 WK 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** U0140-00 - Lost Communication with Body Control Module (BCM). Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2014 WD 5.7L engine (Sales Code EZH) Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2015 WD 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

Some customers may experience one or more of the following conditions:HVAC is shutting off during a cold engine crank due to low voltage, user will need to manually turn HVAC system back on.. Erratic blower speed operation when using HVAC system in auto mode. Brief burst of hot or cold air after adjusting the HVAC temperature setting. Updating the HVAC software will correct these conditions.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB)

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

Engineering is gathering information regarding this system. If no response in 15 minutes, proceed with repair.

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

the Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle. 2015 WK ? Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. ? Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. ? Malfunction Indicator Lamp (MIL) illuminated with Diagnostic Trouble Code (DTC) U0140-00 - Lost Communication with Body Control Module (BCM). 2014 WD ? Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start.

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience one or all of the following: False security alarm activation. A significant delay to update the ambient air temperature display. Intermittently the interior lights may not turn on with the first press of the key fob. Ambient temperature may display - 40 F/-40 C for a few seconds at start up. Courtesy lamps are dim when approaching the vehicle after a remote start. Intermittently the vehicle may not start, after the vehicle has been driven and then trying to restart the vehicle with remote start. Back lighting flickers after a remote start, the condition is gone after entering the vehicle and restarting it. Engine may turn off, after the vehicle is remote started and then unlocking the vehicle with the liftgate passive entry. (Diesel Only) (Diesel Only) False DTC setting for front Daytime Running Lamps (DRL) circuit open, DRL will work properly. False setting for B16D3-15 Right DRL Lamp Control - Circuit Short To Battery Or Open. False setting for B16CF-15 Left DRL Lamp Control - Circuit Short To Battery Or Open.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle: 2015 WK 3.0L engine (Sales Code EHD) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start. 2015 WK 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** U0140-00 - Lost Communication with Body Control Module (BCM). Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2014 WD 5.7L engine (Sales Code EZH) Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2015 WD 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.

Control Module (PCM) with new software. A small number of customers may experience one or more of the symptoms/conditions listed below or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set. If any of the following DTCs have been set perform the Diagnosis: - U0140 - Lost Communication With Body Control Module. Attempting to clear this DTC will be unsuccessful. - P0300 - Multiple Cylinder Misfire (only applies to 5.7L engines). - P0573 - Brake Switch 1 Stuck Off. The following powertrain system improvements/enhancements are also included in this software release: - Corrected a generic scan tool display issue regarding Mode 6 data accuracy. - Improved transmission Quick Learn routine performance (only applies to 5.7L engines).

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle. 2015 WK 3.0L engine (Sales Code EHD) ? Enhancements to remote engine start. 2015 WK 5.7L engine (Sales Code EZH) ? Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. ? Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. ? Malfunction Indicator Lamp (MIL) illuminated with Diagnostic Trouble Code (DTC) U0140-00 - Lost Communication with Body Control Module (BCM). 2014 WD 5.7L engine (Sales Code EZH) ? Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2015 WD 5.7L engine (Sales Code EZH) ? Enhancements to remote engine start.

The customer may notice blue smoke coming from the tail pipe after the vehicle was started. Also after performing an oil change the Dipstick may indicate the oil was low. When changing the oil and filter, service information shows 7 quarts / 6.6 liters are required. After installing 7 quarts / 6.6 liters the Dipstick may indicate the engine oil level is 1 quart / .95 liters low.

with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine. LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to enable the scan tool based transmission ?Quick Learn.? ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) ? Software to correct a harsh bump feel during a 2-1 downshift. WK vehicles equipped with a 3.6L engine (Sales Code ERB) ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Software to correct a harsh bump feel during a 2-1 downshift. DS vehicles equipped with 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. ? Software improvements to powertrain braking in Tow/Haul mode. ? Software to improve downshift response from a medium to heavy pedal acceleration. ? Driveability improvements at higher altitudes. ? Software to improve acceleration during cruise control operation ? Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed inste

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle: 2015 WK 3.0L engine (Sales Code EHD) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start. 2015 WK 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** U0140-00 - Lost Communication with Body Control Module (BCM). Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2014 WD 5.7L engine (Sales Code EZH) Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. 2015 WD 5.7L engine (Sales Code EZH) ** P0456 - EVAP System Small Leak.** Enhancements to remote engine start.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience one or all of the following: False security alarm activation. A significant delay to update the ambient air temperature display. Intermittently the interior lights may not turn on with the first press of the key fob. Ambient temperature may display - 40 F/-40 C for a few seconds at start up. Courtesy lamps are dim when approaching the vehicle after a remote start. Intermittently the vehicle may not start, after the vehicle has been driven and then trying to restart the vehicle with remote start. Back lighting flickers after a remote start, the condition is gone after entering the vehicle and restarting it. Engine may turn off, after the vehicle is remote started and then unlocking the vehicle with the liftgate passive entry. (Diesel Only) (Diesel Only) False DTC setting for front Daytime Running Lamps (DRL) circuit open, DRL will work properly. False setting for B16D3-15 Right DRL Lamp Control - Circuit Short To Battery Or Open. False setting for B16CF-15 Left DRL Lamp Control - Circuit Short To Battery Or Open.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. Software improvements to powertrain braking in Tow/Haul mode. Software to improve downshift response from a medium to heavy pedal acceleration. Driveability improvements at higher altitudes. Software to improve acceleration during cruise control operation Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed instead of U11E3 - TCM Lost communication with ESM On D-PT CAN.WD vehicles equipped with a 3.6L engine (Sales Code ERB)

the Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release. These symptoms are broken down by vehicle. 2015 WK * Enhancements to improve a slight lag or hesitation during Multi Displacement System (MDS) mode transitions. * Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start. * Malfunction Indicator Lamp (MIL) illuminated with Diagnostic Trouble Code (DTC) U0140-00 - Lost Communication with Body Control Module (BCM). 2014 WD * Enhancements to improve a slight drop in engine RPM when the vehicle is shifted to reverse or drive within 3 seconds of a cold start.

This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience one or all of the following: ? False security alarm activation. ? A significant delay to update the ambient air temperature display. ? Intermittently the interior lights may not turn on with the first press of the key fob. ? Ambient temperature may display - 40 F/-40 C for a few seconds at start up. ? Courtesy lamps are dim when approaching the vehicle after a remote start. ? Intermittently the vehicle may not start, after the vehicle has been driven and then trying to restart the vehicle with remote start. ? Back lighting flickers after a remote start, the condition is gone after entering the vehicle and restarting it. ? Engine may turn off, after the vehicle is remote started and then unlocking the vehicle with the liftgate passive entry. ? False U0422-00-Implauible Data Received and turning on the MIL indicator lamp. (Diesel Only) ? Missing DTCs for open or short cabin heater 1, 2 or 3. (Diesel Only) ? False DTC setting for front Daytime Running Lamps (DRL) circuit open, DRL will work properly. ? False setting for B16D3-15 Right DRL Lamp Control - Circuit Short To Battery Or Open. ? False setting for B16CF-15 Left DRL Lamp Control - Circuit Short To Battery Or Open.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Engineering is gathering information regarding this system. If no response in 15 minutes, proceed with repair.

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: (only applies to 5.7L engines) P0573 - Brake Switch 1 Stuck OffThe following powertrain system improvements/enhancements are also included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy. (only applies to 5.7L engines)

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300 - Multiple Cylinder Misfire (only applies to 5.7L engines) ? P0573 - Brake Switch 1 Stuck Off

Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - Evaporative System Small Leak (applies to 2014 MY only). P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible (applies to 2015 MY only).** P0456 - EVAP System Small Leak. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire P0300 - Multiple Cylinder Misfire. P0513 - Invalid SKIM Key.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.

ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR."

MODEL 2014. *PE

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE AND NEW SOFTWARE FOR SELECTIVE ERASING AND REPROGRAMMING OF POWERTRAIN CONTROL MODULE (PCM). MODEL 2014 GRAND CHEROKEE, DURANGO. *PE

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

to replace the load floor assembly for a replacement load floor handle

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Tire Pressure Sensors Values Are Not Displayed

A customer may experience one or more of the following conditions. Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio remains on. HVAC temperature out of sync with radio display (KL vehicles). Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may reset itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear. Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Park Sense tone continuously on. Radio display may show. Please insert USB Stick? Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Tire Pressure Sensors Values Are Not Displayed

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

**Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: **Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may resets itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers (U.S. market only). Able to adjust audio balance / fade settings during a VR session. Correct condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to rev

The customer may notice one or more of the following: **Enhancements to software to correct an issue with the heated seat icon showing up in blue and the heated steering wheel icon remaining a constant red when off instead of grey induced by 15.24.00 flash.** During an ignition cycle, there is loss of functionality to play from the list of media sources: USB (Universal Serial Bus)/SD (Secure Digital) Card/Bluetooth streaming device. Intermittently missing tracks on USB/SD Card media modes. Potential for inoperative or blank radio display. Radio displays message ?Please insert update USB?. AM/FM presets lost over an ignition cycle. iPod Synchronization will be incomplete causing the Voice Recognition (VR) to be inoperative. Display shows multiple USB media song titles in the browse menu. System incorrectly comes up in Aux mode. Unable to change CD tracks with steering wheel controls. May be able to change AM/FM frequencies while changing SXM frequencies. Display screen dim. Paired phone list is deleted after ignition cycle. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. SXM disappeared and failed to re-register. Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Audio controls are locked out after using VR. iPod will not resume playing after phone call. iPod ?Repeat? function is not turned on. iPod songs not accessible through VR without ?genre?. iPod shuffle does not continue after ignition cycle. Not able to restore to default setting. Potential for battery draw on E-Call function. Steering wheel control seek up/down function not working. Steering wheel control press and hold skippi

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

A customer may experience, one or more of the following conditions. Navigation function may resets itself after using One-Shot Voice Recognition (VR). Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers. (U.S. market only) Able to adjust audio balance / fade settings during a VR session. Correct, condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Enhancement to navigation routing. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. Enhancements for iPod or iPhone devices that may not start playing after connecting. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system response time. Compass indicator turns off. Touch screen shut down message. Radio surround sound will not stay ON. Driver memory feature causes Sirius XM failure. Loss of radio presets. Battery drain - due to radio remains on. Uconnect apps don't load. AM/FM popping noises and/or static. Backup camera display is blank

? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

The customer may experience one or both of the following condition: ? Vehicle will not start. If the backup start mode is tried (press the FOB against the Start/Stop button) a message in the cluster will be displayed ?Key Not Detected?. ? The power liftgate intermittently may not open. It may be required to press the power liftgate button on the FOBIK two more times to open the power liftgate.

Customers may experience the following condition: ? Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint. ? Heat mode becomes active when the radio is configured to read in C and cabin temperature is set to LO. Updating the HVAC software will correct these conditions.

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

The customer may experience one or both of the following condition: ? Vehicle will not start. If the backup start mode is tried (press the FOB against the Start/Stop button) a message in the cluster will be displayed ?Key Not Detected?. ? The power liftgate intermittently may not open. It may be required to press the power liftgate button on the FOBIK two more times to open the power liftgate.

Customers may experience the following condition: ? Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint. ? Heat mode becomes active when the radio is configured to read in C and cabin temperature is set to LO. Updating the HVAC software will correct these conditions.

repair to the sun visor, headliner or while gaining access above the headliner. This may result in an inoperative vanity lamp and/or an electrical fire.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

The customer may notice one or more of the following: ? Potential for inoperative or blank radio display. ? Radio displays message ?Please insert update USB? ? AM/FM presets lost over an ignition cycle. ? Ipod Synchronization will be incomplete causing the voice recognition to be inoperative. ? Display shows multiple USB media song titles in the browse menu. ? System incorrectly comes up in Aux mode. ? Unable to change CD tracks with steering wheel controls. ? May be able to change AM/FM frequencies while changing SXM frequencies. ? Display screen dim. ? Paired phone list is deleted after ignition cycle. ? Not able to pair phone. ? Unable to delete paired device from list. ? Removed the ability to pair phones while the vehicle is in motion. ? Voice command not able to play new text messages. ? SXM presets are lost at times. ? SXM disappeared and failed to re-register. ? Intermittently the wrong selected media is played. ? Noises (pops and cracks) for AM/FM. ? Audio controls are locked out after using Voice Recognition (VR). ? IPOD will not resume playing after phone call. ? IPOD ?Repeat? function is not turned on. ? IPOD songs not accessible through VR without ?genre?. ? IPOD shuffle does not continue after ignition cycle. ? Not able to restore to default setting. ? Potential for battery draw on E-Call function. ? Steering wheel control seek up/down function not working. ? Steering wheel control press and hold skipping channels. ? Intermittently the wrong pop-ups or displays is shown. ? Intermittently the phone or media will freeze. ? Presets or clock setting are lost after software updates. ? Climate ON/OFF pop-up will not longer appear. ? Can?t change media source to Disc. ? Wrong EQ setting being used. ? Mute function not working correctly. ? No audio on phone calls. Improvements ? VR command, p

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

The customer may experience one or both of the following condition: ? Vehicle will not start. If the backup start mode is tried (press the FOB against the Start/Stop button) a message in the cluster will be displayed ?Key Not Detected?. ? The power liftgate intermittently may not open. It may be required to press the power liftgate button on the FOBIK two more times to open the power liftgate.

Customers may experience the following condition: ? Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint. ? Heat mode becomes active when the radio is configured to read in C and cabin temperature is set to LO. Updating the HVAC software will correct these conditions.

A customer may experience, one or more of the following conditions. ? Improved Radio security protection to reduce the potential risk of unauthorized and unlawful access to vehicle systems (U.S. Market Only). ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connec

A customer may experience, one or more of the following conditions. ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system respo

performing a Misc-function routine. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): ? C151D - Tire Pressure Sensor Location Undetermined. ? C1581 - Front/Rear Side Tire Pressure Sensor Location Undetermined.

A customer may experience, one or more of the following conditions. Navigation function may resets itself after using One-Shot Voice Recognition (VR). Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers. (U.S. market only) Able to adjust audio balance / fade settings during a VR session. Correct, condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on Enhancement to navigation routing Radio display may shows ?Please insert USB Stick? Enhancement made when video is display in radio when using PAL format video disks Corrected the temperature slider bar not updating on Manual Temperature Control vehicles Navigation may not start or may lose position Rear camera may show a black screen for 3 seconds upon going to reverse Enhancements for iPod or iPhone devices that may not start playing after connecting iPod would not resume playing after a VR session or phone call Radio reset, screen lockup, blank screen or sluggish system response time Compass indicator turns off Touch screen shut down message Radio surround sound will not stay ON Driver memory feature causes Sirius XM failure Loss of radio presets Battery drain-due to radio remains on Uconnect apps don't load AM/FM popping noises and/or static Backup camera display is blank Compass direction may be inco

? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

DAB (Digital Audio Broadcast) is inoperative. Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. DAB preset list on the top of the screen doesn't change while scrolling with steering controls. Rear view camera jitter. Tuner reception software enhancements. HVAC temperature control enhancements. SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only). AM/FM steering wheel mode switch button not working (LATAM markets only). Navigation Lockout Disable while vehicle is in motion (EMEA markets only). Removed network status indicators for SRT/APPS. Voice Recognition (VR) says 'cancel' when starting (App) applications. iPod would not resume playing after a VR session or phone call. Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. rear camera may show a black screen for 3 seconds upon going to reverse. Navigation would not start or would lose position. Removal of parental control under Apps menu. Turn by Turn navigation in the cluster set to ON by default. Transfer button does not pick-up and transfer incoming call. Some Russian letters are caps when they should be lower-case. Touch screen locks up in navigation, when Russian is selected. Address search availably when the vehicle is moving (EMEA markets only). VR messages in Spanish talks to fast. Recognition enhancement for Russian VR. Hands free audio too low for non-amp vehicle (KL). Intermittently Registration expired pop-up appears on display screen. Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). Incorrect time to destination

The customer may notice one or more of the following. Unable to change CD tracks with steering wheel controls. May be able to change AM/FM frequencies while changing SXM frequencies. Display screen dim. Paired phone list is deleted after ignition cycle. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. SXM presets are lost at times. SXM disappeared and failed to re-register. Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Audio controls are locked out after using VR. IPOD will not resume playing after phone call. IPOD Repeat? function is not turned on. IPOD songs not accessible through VR without genre?. IPOD shuffle does not continue after ignition cycle. Not able to restore to default setting. Potential for battery draw on E-Call function. Steering wheel control seek up/down function not working. Steering wheel control press and hold skipping channels. Intermittently the wrong pop-ups or displays is shown. Intermittently the phone or media will freeze. Presets or clock setting are lost after software updates. Climate ON/OFF pop-up will not longer appear. Can?t change media source to Disc. Wrong EQ setting being used. Mute function not working correctly. No audio on phone calls.Improvements VR command, prompts and recognition. Blue Tooth Streaming Audio, connection and playing. Audio during hands free calling. Phone book downloading and display. Retaining/storing all presets and improvements to presets from skipping channels. Text message downloading and playing.

The customer may notice one or more of the following: Unable to change CD tracks with steering wheel controls. Scroll knob may not functioning on Digital Audio Broadcasting (DAB). Paired phone list is deleted after ignition cycle. Incorrect Russian translations. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. Screen going very dim. DAB service lost. (EMEA Market Only). Not able to refresh? screen in DAB mode.(EMEA Market Only). Steering wheel control mode advance from FM to AM (LATAM Market Only). Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Unable to delete paired device from list. Unable to deactivate alternate frequency. Audio controls are locked out after using VR. IPOD will not resume playing after phone call. IPOD Repeat? function is not turned on. IPOD songs not accessible through VR without genre?. IPOD shuffle does not continue after ignition cycle. Not able to restore to default setting. Steering wheel control seek up/down function not working. Steering wheel control press and hold skipping channels. Intermittently the wrong pop-ups or displays is shown. Intermittently the phone or media will freeze. Presets or clock setting are lost after software updates. Climate ON/OFF pop-up will not longer appear. Can?t change media source to Disc. Wrong EQ setting being used. Mute function not working correctly. No audio on phone calls.Improvements VR command, prompts and recognition. Blue Tooth Streaming Audio, connection and playing. Audio during hands free calling. Phone book downloading and display. Retaining/storing all presets and improvements to presets from skipping channels. Text message downloading and playing.

Customers may experience the following condition: Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint.Updating the HVAC software will correct these conditions.

Some customers may experience one or more of the following conditions. ? Erratic blower speed operation when using HVAC system in auto mode. ? Brief burst of hot or cold air after adjusting the HVAC temperature setting.Updating the HVAC software will correct these conditions.

Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles). Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may resets itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear Vehicle Phone Requires Service even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers (U.S. market only). Able to adjust audio balance / fade settings during a VR session. Correct condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Enhancement to navigation routing. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to rev

The customer may notice one or more of the following: Enhancements to software to correct an issue with the heated seat icon showing up in blue and the heated steering wheel icon remaining a constant red when off instead of grey induced by 15.24.00 flash. During an ignition cycle, there is loss of functionality to play from the list of media sources: USB (Universal Serial Bus)/SD (Secure Digital) Card/Bluetooth streaming device. Intermittently missing tracks on USB/SD Card media modes. Potential for inoperative or blank radio display. Radio displays message Please insert update USB. AM/FM presets lost over on ignition cycle. iPod Synchronization will be incomplete causing the Voice Recognition (VR) to be inoperative. Display shows multiple USB media song titles in the browse menu. System incorrectly comes up in Aux mode. Unable to change CD tracks with steering wheel controls. May be able to change AM/FM frequencies while changing SXM frequencies. Display screen dim. Paired phone list is deleted after ignition cycle. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. SXM presets are lost at times. SXM disappeared and failed to re-register. Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Audio controls are locked out after using VR. iPod will not resume playing after phone call. iPod Repeat function is not turned on. iPod songs not accessible through VR without genre. iPod shuffle does not continue after ignition cycle. Not able to restore to default setting. Potential for battery draw on E-Call function. Steering wheel control seek up/down function not working. Steering wheel control press and hold skippi

reprogramming the HVAC Module with new software. Customers may experience the following condition: ? Vehicle cabin temperature seems too warm even after reducing the Automatic Temperature Control setpoint. Updating the HVAC software will correct these conditions.

A customer may experience, one or more of the following conditions. ? Navigation display enhancement. ? Enables Via Mobile software features when released to consumers. ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system response time. ? Compass indicator turns off. ? Touch screen shut down message. ? Radio surround sound will not stay ON. ? Driver memory feature causes Sirius XM failure. ? Loss of radio presets. ? Battery drain - due to radio remains on. ? Uconnect apps don't load. ? AM/FM popping noises and/or static. ? Backup camera display is blank. ? Compass direction may be incorrect. ? Vehicle's Icon changes on the navigation map. ? Loss of vehicle position on NAV map. ? ?Vehicle Phone Requires Service? message appears on 8.4? screen. ? Nav turn-by-turn enhancements. ? Nav map guidance enhancements. ? Nav text overlaps in detour menu. ? Nav map, vehicle location enhancements in areas with low GPS signals. ? Navigation shows vehicle in San

The customer may notice one or more of the following. ? Display screen dim. ? Paired phone list is deleted after ignition cycle. ? Not able to pair phone. ? Unable to delete paired device from list. ? Removed the ability to pair phones while the vehicle is in motion. ? Voice command not able to play new text messages. ? SXM presets are lost at times. ? SXM disappeared and failed to re-register. ? Intermittently the wrong selected media is played. ? Noises (pops and cracks) for AM/FM. ? Audio controls are locked out after using VR. ? IPOD will not resume playing after phone call. ? IPOD ?Repeat? function is not turned on. ? IPOD songs not accessible through VR without ?genre?. ? IPOD shuffle does not continue after ignition cycle. ? Not able to restore to default setting. ? Potential for battery draw on E-Call function. ? Steering wheel control seek up/down function not working. ? Steering wheel control press and hold skipping channels. ? Intermittently the wrong pop-ups or displays is shown. ? Intermittently the phone or media will freeze. ? Presets or clock setting are lost after software updates. ? Climate ON/OFF pop-up will not longer appear. ? Can?t change media source to Disc. ? Wrong EQ setting being used. ? Mute function not working correctly. ? No audio on phone calls. Improvements ? VR command, prompts and recognition. ? Blue Tooth Streaming Audio, connection and playing. ? Audio during hands free calling. ? Phone book downloading and display. ? Retaining/storing all presets and improvements to presets from skipping channels. ? Text message downloading and playing.

? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when ignition is cycled. ? Volume adjustment for navigation prompts, for phone call. ? Incorrect rear to center fade displayed at start up. ? Translation enhancements for French German and Spanish. ? Right arrow doesn't work for advancing through preset. ? Map zoom level reduced. ? Park sense audio tone stuck on. ?

The customer may notice one or more of the following. ? Paired phone list is deleted after ignition cycle. ? Not able to pair phone. ? Unable to delete paired device from list. ? Removed the ability to pair phones while the vehicle is in motion. ? Voice command not able to play new text messages. ? SXM presets are lost at times. ? SXM disappeared and failed to re-register. ? Intermittently the wrong selected media is played. ? Noises (pops and cracks) for AM/FM. ? Audio controls are locked out after using VR. ? IPOD will not resume playing after phone call. ? IPOD ?Repeat? function is not turned on. ? IPOD songs not accessible through VR without ?genre?. ? IPOD shuffle does not continue after ignition cycle. ? Not able to restore to default setting. ? Potential for battery draw on E-Call function. ? Steering wheel control seek up/down function not working . ? Steering wheel control press and hold skipping channels . ? Intermittently the wrong pop-ups or displays is shown. ? Intermittently the phone or media will freeze. ? Presets or clock setting are lost after software updates. ? Climate ON/OFF pop-up will not longer appear. ? Can?t change media source to Disc. ? Wrong EQ setting being used. ? Mute function not working correctly. ? No audio on phone calls. Improvements ? VR command, prompts and recognition. ? Blue Tooth Streaming Audio, connection and playing. ? Audio during hands free calling. ? Phone book downloading and display. ? Retaining/storing all presets and improvements to presets from skipping channels. ? Text message downloading and playing.

Modules (DMFL/DMFR) with new software. Customer may experience that the outside power mirrors will not tilt enough when the vehicle is in reverse.

A customer may experience not being able to turn off the ?Comfort Auto On? feature in the customer settings.

The customer may notice one or more of the following: **During an ignition cycle, there is loss of functionality to play from the list of media sources: USB (Universal Serial Bus)/SD (Secure Digital) Card/Bluetooth streaming device. Intermittently missing tracks on USB/SD Card media modes.** Potential for inoperative or blank radio display. Radio displays message ?Please insert update USB?. AM/FM presets lost over an ignition cycle. iPod Synchronization will be incomplete causing the Voice Recognition (VR) to be inoperative. Display shows multiple USB media song titles in the browse menu. System incorrectly comes up in Aux mode. Unable to change CD tracks with steering wheel controls. May be able to change AM/FM frequencies while changing SXM frequencies.Display screen dim. Paired phone list is deleted after ignition cycle. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. SXM presets are lost at times. SXM disappeared and failed to re-register. Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Audio controls are locked out after using VR. iPod will not resume playing after phone call. iPod ?Repeat? function is not turned on. iPod songs not accessible through VR without ?genre?. iPod shuffle does not continue after ignition cycle. Not able to restore to default setting. Potential for battery draw on E-Call function. Steering wheel control seek up/down function not working. Steering wheel control press and hold skipping channels. Intermittently the wrong pop-ups or displays are shown. Intermittently the phone or media will freeze. Presets or clock setting are lost after software updates. Climate ON/OFF pop-up

required.?Navigation Failed? message is displayed (2014 MY WK and KL with RG4). Clock does not automatically update to local time (2014 MY WK and KL with RG4). Poor or no connection to cellular network (2014 MY WK and KL with RG4). HVAC temperature out of sync with radio display (2014 MY KL with RG4). Some Uconnect App remote commands do not execute with the vehicle (2014 MY WK and KL with RG4). Display goes blank/black (2014 MY WK and KL with RG4).Cyrillic keyboard is missing in phone book (2014 MY WK and KL with RG4).Incorrect speed limit on NAV speed camera indication (2014 MY WK and KL with RG4). Poor reception for AM/FM radio.Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played.SD, USB or BTSA modes may become non-functional for a given ignition cycle.Track names may be displayed twice in USB or SD media modes.Voice Recognition (VR) command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK)Vehicle only.DAB is inoperative.Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed camera UK&Spain complaining that the speed camera feature was not available with the latest MY14 software.SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only).Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only).AM/FM steering wheel mode switch button not working (LATAM markets only).Navigation Lockout Disable while vehicle is in motion (EMEA markets only).Removed network status indicators for SRT/APPS.VR says 'cancel' when starting (App) applications.iPod would not resume playing after a VR session or phone call.Removed the cell signal indicators in the SRT and Apps button on non-US vehicles.Rear camera may show a black screen for 3 secon

Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits. Updating the HVAC software will correct these conditions.

The customer may notice one or more of the following: Potential for inoperative or blank radio display. Radio displays message ?Please insert update USB?. AM/FM presets lost over an ignition cycle. iPod Synchronization will be incomplete causing the voice recognition to be inoperative. Display shows multiple USB media song titles in the browse menu. System incorrectly comes up in Aux mode. Unable to change CD tracks with steering wheel controls. May be able to change AM/FM frequencies while changing SXM frequencies. Display screen dim. Paired phone list is deleted after ignition cycle. Not able to pair phone. Unable to delete paired device from list. Removed the ability to pair phones while the vehicle is in motion. Voice command not able to play new text messages. SXM presets are lost at times. SXM disappeared and failed to re-register. Intermittently the wrong selected media is played. Noises (pops and cracks) for AM/FM. Audio controls are locked out after using Voice Recognition (VR). iPod will not resume playing after phone call. iPod ?Repeat? function is not turned on. iPod songs not accessible through VR without ?genre?. iPod shuffle does not continue after ignition cycle. Not able to restore to default setting. Potential for battery draw on E-Call function. Steering wheel control seek up/down function not working. Steering wheel control press and hold skipping channels. Intermittently the wrong pop-ups or displays are shown. Intermittently the phone or media will freeze. Presets or clock setting are lost after software updates. Climate ON/OFF pop-up will not longer appear. Cannot change media source to Disc. Wrong EQ setting being used. Mute function not working correctly. No audio on phone calls.

more of the following: **Enhancements to software to correct an issue with the heated seat icon showing up in blue and the heated steering wheel icon remaining a constant red when off instead of grey induced by 15.24.00 flash.** During an ignition cycle, there is loss of functionality to play from the list of media sources: USB (Universal Serial Bus)/SD (Secure Digital) Card/Bluetooth streaming device. Intermittently missing tracks on USB/SD Card media modes. Potential for inoperative or blank radio display. Radio displays message Please insert update USB.

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR has inadvertently deployedFig.1andFig.2on one or both front seats and will not reset. Inadvertent Deployed Position AHR1 - Sled Fractured And Pin In Latch2 - Pin Fastened To SledNormal Deployed Position AHR1 - Striker Pin2 - Latch Pawls3 - Sled4 - Sled Bracket5 - Tilt Clip

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

the front seat belt retractor D-rings for cracks, whitening or witness marks on the plastic overmolds. Customers may comment on one or more of the following:The front driver and or passenger seat belts may not retract properly. A front seat belt D-ring plastic is cracked.

the front seat belt retractor D-rings for cracks, whitening or witness marks on the plastic overmolds. Customers may comment on one or more of the following:The front driver and or passenger seat belts may not retract properly. A front seat belt D-ring plastic is cracked.

Jeep Grand Cherokee (WK)

the front seat belt retractor D-rings for cracks, whitening or witness marks on the plastic overmolds. Customers may comment on one or more of the following:The front driver and or passenger seat belts may not retract properly. A front seat belt D-ring plastic is cracked.

the front seat belt retractor D-rings for cracks, whitening or witness marks on the plastic overmolds. Customers may comment on one or more of the following:The front driver and or passenger seat belts may not retract properly. A front seat belt D-ring plastic is cracked.

Jeep Grand Cherokee (WK)

bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

D)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR has inadvertently deployedFig.1andFig.2on one or both front seats and will not reset. Inadvertent Deployed Position AHR1 - Sled Fractured And Pin In Latch2 - Pin Fastened To SledNormal Deployed Position AHR1 - Striker Pin2 - Latch Pawls3 - Sled4 - Sled Bracket5 - Tilt Clip

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

The customer may notice one or more of the following. Unable to select ?Portuguese and Polish? languages on VP2 ECE Radio. Unable to select ?Turkish and Brazil-Portuguese? languages on VP2 ROW Radio.

18.01.35 (BU Vehicles)

No FM or AM reception.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

(AMP) with the latest available software. The customer may describe when changing the radio tone settings (bass, mid, treble) the volume levels may be erratic. Depending where the volume is set, the volume changes may be very loud or very quiet. Example: When the volume is set to 8 and making adjustments to the tone settings, the volume can increase by 15 db. When the volume is set to 25 and making adjustments to the tone settings, there maybe no volume changes. The customer may also describe when listening with the volume set to 9 there is more bass and less mid/high. When the volume is set to 10 is less bass and more mid/high (WD,WK, W2 and W3 only).

(AMP) with the latest available software. The customer may describe when changing the radio tone settings (Bass, Mid, Treble) the volume levels may be erratic. Depending where the volume is set, the volume changes maybe very loud or very little. Example: Volume set to 8 and making adjustments to the tone settings, the volume can increase by 15 db. Volume set to 25 and making adjustments to the tone settings, there maybe no volume changes.

No FM or AM reception.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

The customer may notice one or more of the following. Unable to select ?Portuguese and Polish? languages on VP2 ECE Radio. Unable to select ?Turkish and Brazil-Portuguese? languages on VP2 ROW Radio.

A customer may experience, one or more of the following conditions. Peru maps not available. When using navigation route guidance with Spanish language selected the customer will have English voice guidance presented when it should be in Spanish.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus. On further inspection U0186-00 Lost communication with the audio amplifier may be found.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

SYMPTOM/CONDITION: **Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.**

MODEL 2013-14. *PE

INSTRUMENT CLUSTER "SERVICE TIRE PRESSURE SYSTEM". *LJ

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

There is a potential for water intrusion which over time could lead to an inoperable license plate lamp. Customers may comment on one or more of the following: ? License plate LED light is inoperable. ? Moisture in the license plate lamp housing. This bulletin involves inspecting the license plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a additional O-ring and foam gasket to the license plate applique

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Cherokee and Dodge Durango) or LD/LX (Dodge Charger and Chrysler 300) 2014, 2015, 2016 MY 0 to 36,000 miles, FCA is looking to gather information prior to repairing the vehicle. Please contact Kevin Murphree via Cell Phone (248) 613-3417.~ If the dealership is within the Metro Detroit Area, Kevin would like to analyze the vehicle in person prior to repair.~

Customers may comment on the following:Rattle coming from sunroof.

Sunroof Drain Tube Inspection.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may describe a broken cargo compartment load floor panel latch handle.

Cherokee and Dodge Durango) or LD/LX (Dodge Charger and Chrysler 300) 2014, 2015, 2016 MY 0 to 36,000 miles, FCA is looking to gather information prior to repairing the vehicle. Please contact Kevin Murphree via Cell Phone (248) 613-3417.~ If the dealership is within the Metro Detroit Area, Kevin would like to analyze the vehicle in person prior to repair.~

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience not being able to shift out of park. This condition can be corrected by turning off the vehicle and allowing all of the modules to go to sleep. Once the modules have gone through a key cycle the DTC will go from active to stored and then the vehicle can be shifted out of park. On further inspection DTCs P0607-00-ECU INTERNAL PERFORMANCE and P0928-00-BTSI CONTROL may be found active or stored.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

with the latest available software. A small number of customers may indicate that the transmission shift quality may not meet their expectations under the following conditions. These concerns are separated by vehicle. WK Vehicles ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Less than desired upshift quality in normal drive mode under light/medium acceleration. ? Less than desired Power-on downshift quality (i.e. passing). ? Less than desired powertrain performance while driving at higher altitudes, on steep grades, or during high speed driving. ? Less than desired tip in/out acceleration during torque converter clutch operation. ? Less than desired engagement quality in 4x4 high or 4x4 low range. WD Vehicles ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Less than desired engagement quality in 4x4 high or 4x4 low range.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer's concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience not being able to shift out of park. This condition can be corrected by turning off the vehicle and allowing all of the modules to go to sleep. Once the modules have gone through a key cycle the DTC will go from active to stored and then the vehicle can be shifted out of park. On further inspection DTCs P0607-00-ECU INTERNAL PERFORMANCE and P0928-00-BTSI CONTROL may be found active or stored.

Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle drivability and shift quality may not meet their expectations while in ECO Mode.

Transmission Control Module (TCM) with new software. Customers may indicate that the shift quality while in 4X4 low range mode does not meet their expectations.

need to be replaced with updated components if front park/turn signal bulb is inoperative.

plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a foam gasket to the license plate applique. Customers may comment on one or more of the following: License plate LED light is inoperable. Moisture in the license plate lamp housing.

industry awareness regarding the use of recycled or salvage parts.

plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a foam gasket to the license plate applique. Customers may comment on one or more of the following: License plate LED light is inoperable. Moisture in the license plate lamp housing.

plate LED lamp for being inoperative or visible signs of moisture within the LED lamp housing and if necessary replacing the LED and installing a foam gasket to the license plate applique. Customers may comment on one or more of the following: License plate LED light is inoperable. Moisture in the license plate lamp housing.

industry awareness regarding the use of recycled or salvage parts.

Some vehicles may have been built with loose front half shaft boot clamps. A loose front half shaft boot clamp could allow the boot to come loose allowing moisture and debris into the CV joint.

Some vehicles may have been built with loose front half shaft boot clamps. A loose front half shaft boot clamp could allow the boot to come loose allowing moisture and debris into the CV joint.

DODGE DURANGO, JEEP GRAND CHEROKEE: FRONT HALF BOOT CLAMPS ON ABOVE VEHICLES MAY HAVE BEEN INCOORECTLY INSTALLED, WHICH COULD ALLOW GREASE FROM THE CV JOINT TO LEAK WHILE DRIVING. *LJ

FRONT HALF SHAFT CLAMPS HAVE BEEN INSTALLED INCORRECTLY. *LJ

CV JOINT, AND NEED TO HAVE BOTH REPLACED. MODEL 2014 DURANGO, GRAND CHEROKEE. *PE

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

Please call one of these 3 people on their cell phone before replacing the HVAC filter or the evaporator:~ Pat Presti ? (248) 379-0972~ Ken Deneau ? (248) 576-1870~ Murali Govindarajalu ? (248) 421-2483

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies to 2014-2015 WD, WK or KL Vehicles. A customer may experience a popping noise when listening to AM stations.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

Customer may experience vibration in the steering wheel while driving at speeds between 65 to 80 mph.

Customer may experience vibration in the steering wheel while driving at speeds between 65 to 80 mph.

operation of the Auto Comfort feature. The customer may notice when the weather is cold the heated steering wheel and heated seats will automatically turn on. The customer will have to turn off both systems each time the key is cycled. There is no personal setting in the menu to have the Auto Comfort System default to off when the vehicle is started. Reconfiguring the vehicle will give the customer the option to have this feature be on or off when the vehicle is started.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

65 TO 80 MPH, AND WOULD THE FRONT WHEEL BEARINGS REPLACED. MODEL 2014 DURANGO, GRAND CHEROKEE. *PE

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

The rear shocks may produce a rattle chuckle noise while driving over bumps at low speed. The noise is more prevalent at higher shock temperatures.

The customer may describe a front brake squeak/squeal noise at cold temperatures or with cold brakes after sitting. Noise is most prevalent during a low-speed stop with light brake pedal effort.

The rear shocks may produce a rattle chuckle noise while driving over bumps at low speed. The noise is more prevalent at higher shock temperatures.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

B)

procedures outlined in CSN P39.

procedures outlined in CSN P39.

procedures outlined in CSN P39.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

technician an overview of the steps a customer will need to take to complete the update.