2013 Dodge Durango TSBs

for replacement as a remedy for fluid leak.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Engineering is gathering information regarding this system. If no response in 15 minutes, proceed with repair.

Control Module (TCM) with new software. NOTE: This bulletin applies to the following vehicles: Wrangler vehicles equipped with the WA580 Automatic Transmission (Sales Code DGJ) Challenger vehicles equipped with either the 3.6L engine (Sales Code ERB) or the 6.4L Engine (Sales Code ESH or ESG) and the WA580 Automatic Transmission (.Sales Code DGJ) Durango vehicles equipped with the 3.6L engine (Sales Code ERB) and the WA580 Automatic Transmission (Sales Code DGJ) Grand Cherokee vehicles equipped with the 6.4L engine (Sales Code ESG) for all markets except Australia (Sales Code 8AL) or the 3.6L engine (Sales Code ERB) (All Markets) and the WA580 Automatic Transmission (Sales Code DGJ). Australian vehicles equipped with the 6.4L can refer to Service Bulletin 21-010-14

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

Also Includes Powertrain System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following condition: Engine is difficult to start in extreme cold ambient temps when using the block heater. This release improves the spark and fueling strategy used under these conditions.The following system improvements have also been included in this software release: Improved Electronic Voltage Regulator control to more precisely maintain system voltage.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.

Powertrain Control Module (PCM) with new software. The customer may describe a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? P0122 - Throttle Position Sensor 1 Circuit Low (6.4L engine (sales code ESG). ? P0123 - Throttle Position Sensor 1 Circuit High (6.4L engine (sales code ESG). ? P0222 - Throttle Position Sensor 2 Circuit Low (6.4L engine (sales code ESG). ? P0223 - Throttle Position Sensor 2 Circuit High (6.4L engine (sales code ESG). ? P0456 - Evap System Small Leak.

A customer may experience, not being able to change the blower motor speed with the rear HVAC controls.

Control Module (TCM) with new software. The customer may experience one or more of the following: Grand Cherokee/Durango 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Grand Cherokee 6.4L Engine (Sales Code ESG) ? Poor acceleration or performance above 113 kph (70 mph). ? Transmission shifting while accelerating from a stop does not meet customers expectation. ? Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. ? Cannot accelerate up a steep incline or with a loaded trailer in reverse. Wrangler 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Hanging in gear (2nd Gear) when driving up steep hill or Towing (Rubicon ONLY). ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) - Rubicon Only. Wrangler 2.8L Engine (Sales Code ENS) Erratic while driving in Low Range (4LO). Transmission shifts in

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

Also Includes Powertrain System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following condition: Engine is difficult to start in extreme cold ambient temps when using the block heater. This release improves the spark and fueling strategy used under these conditions.The following system improvements have also been included in this software release: Improved Electronic Voltage Regulator control to more precisely maintain system voltage.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

A customer may experience, not being able to change the blower motor speed with the rear HVAC controls.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

Engineering is gathering information regarding this system. If no response in 15 minutes, proceed with repair.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

to replace the load floor assembly for a replacement load floor handle

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

updating the Passive Entry Module (PEM) with new software. Customers may experience an unresponsive remote entry transmitter integrated key FOB.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits.Updating the HVAC software will correct these conditions.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

updating the Passive Entry Module (PEM) with new software. Customers may experience an unresponsive remote entry transmitter integrated key FOB.

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Automatic Oil Change Indicator(AOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the AOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Automatic Oil Change Indicator(AOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the AOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Powertrain Control Module (PCM) with new software.This is an optional software update that should only be used in situations where the customer is specifically complaining of the condition described below. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 40-80 mph (64-129 km/h). Some customers may also describe the sensation similar to that of a fish biting on a fishing line.This is an optional software update that should only be used in situations where the customer is specifically complaining of the above condition. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this SB contains the verbiage ?REFERENCE SB 18-035-14. THIS FLASH TO BE USED ONLY FOR SHUDDER COMPLAINTS?. The other file is the standard software that does not contain improvements for this complaint. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version.If the customer complains of the above condition, perform the Repair Procedure.

repair to the sun visor, headliner or while gaining access above the headliner. This may result in an inoperative vanity lamp and/or an electrical fire.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Powertrain Control Module (PCM) with new software.This is an optional software update that should only be used in situations where the customer is specifically complaining of the condition described below. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 40-80 mph (64-129 km/h). Some customers may also describe the sensation similar to that of a fish biting on a fishing line.This is an optional software update that should only be used in situations where the customer is specifically complaining of the above condition. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this SB contains the verbiage ?REFERENCE SB 18-035-14. THIS FLASH TO BE USED ONLY FOR SHUDDER COMPLAINTS?. The other file is the standard software that does not contain improvements for this complaint. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version.If the customer complains of the above condition, perform the Repair Procedure.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

updating the Passive Entry Module (PEM) with new software. Customers may experience an unresponsive remote entry transmitter integrated key FOB.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Automatic Oil Change Indicator(AOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the AOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message.

A customer may experience, no response or slow response to cruise control switch activations. Issues will be experienced by the customers that activate/press the switches in a very fast manner.

Powertrain Control Module (PCM) with new software. The customer may describe a Malfunction Indicator Lamp (MIL) illumination.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Customers may comment on the following:Rattle coming from sunroof.

Sunroof Drain Tube Inspection.

and if necessary adding grease and, depending on build range, RTV to both rear jounce bumpers. Squeak and/or creak sound coming from rear of vehicle when driving over rough roads.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

verifying and if necessary, replacing the right and left rear shock absorbers. Rattle and/or clunk noise from the rear of the vehicle.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

Rattle and/or clunk noise from the rear of the vehicle equipped with load leveling suspension.

The customer may describe a front brake squeak/squeal noise at cold temperatures or with cold brakes after sitting. Noise is most prevalent during a low-speed stop with light brake pedal effort.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

verifying and if necessary, replacing the right and left rear shock absorbers. Rattle and/or clunk noise from the rear of the vehicle.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2012 and 2013 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. The brake pedal may require additional application force to apply the brakes during certain braking events. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to reprogram the Antilock Brake System (ABS) module. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. Chrysler anticipates the launch of this safety recall in March 2014. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

MOUNTING BOLTS BEING TOO LONG AND A RATTLING NOISE IS HEARD. MODEL 2013-2014 GRAND CHEROKEE, 2013 DURANGO. *PE

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

D)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Control Module (TCM) with new software.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee Poor acceleration or performance above 113 kph (70 mph). Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee. Poor acceleration or performance above 113 kph (70 mph).Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F).

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

*CN

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

MODEL 2013-14. *PE

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star. UPDATE: 11/9/2016 If the new bearing does not fit through the double dash, you need to replace the lower double dash panel to the latest level. Please see the updated flowchart in StarParts for the correct replacement panel.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

B)