2006 Dodge Durango TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement please order 68253099AA. Note: Insulator color is not relevant for service

The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.

replacing the fuel filler tube if the condition occurs.When removing the existing fuel filler tube note how it comes out to aid in installation of the new part. Some customers may experience a fuel spit back condition during a refueling event.

The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.

replacing the fuel filler tube if the condition occurs. NOTE: When removing the existing fuel filler tube note how it comes out to aid in installation of the new part. Some customers may experience a fuel spit back condition during a refueling event.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

replacing the fuel filler tube if the condition occurs.When removing the existing fuel filler tube note how it comes out to aid in installation of the new part. Some customers may experience a fuel spit back condition during a refueling event.

replacing the fuel filler tube if the condition occurs.When removing the existing fuel filler tube note how it comes out to aid in installation of the new part. Some customers may experience a fuel spit back condition during a refueling event.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

DUE TO INLET CHECK VALVE, WHEN REFUELING VEHICLE, THE FUEL WOULD SPIT BACK AND THE FUEL FILLER TUBE NEEDS TO BE REPLACED. MODEL 2005-2006 DURANGO. *PE

*KB UPDATED 8/17/12. *PE

*TT

*AK

DELAYED ENGAGEMENT WHEN THE SHIFTER IS PLACED INTO GEAR AFTER THE ENGINE HAS BEEN OFF FOR MORE THAN 12 HOURS. *TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*NJ

*KB

*TT

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

The HFM fails to operate causing the UConnect Hands Free Communications system to not respond when system activation is attempted by the customer. Further diagnosis may reveal that when the wiTECH scan tool is used to read Diagnostic Trouble Codes (DTCs) the tool indicates that the module is not responding. Other modules on the bus may display loss of communication with the HFM. If the Hands Free Communication system is unresponsive then the HFM may require electronic reset.To perform a electronic reset, turn off the vehicle and pull the Ignition Off Drain (IOD) fuse. Wait a few minutes before reinstalling the IOD fuse and checking if the HFM is communicating. If the HFM still will not communicate, then normal No Response diagnostic should be performed. If the HFM is working properly, the module should be replaced to prevent this condition from happening again.

TO DIAGNOSTIC TROUBLE CODE P0340, P0344 OR P0116. THIS INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH NEW SOFTWARE. *PE UPDATED 5/24/10. *PE

*KB

*KB

*TT

*TS

*TT

required to attach Neutral Start Switch

required to attach Neutral Start Switch

*SC

*SC

*TT

VARIOUS MODELS INCLUDING THE 2004 RAM TRUCK, DURANGO, SEBRING CONVERTIBLE, CHEROKEE, VISION, NEON, AND VOYAGER. *TT *SC

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the blade key (no immobilizer & no transmitter) P/N 05018689AA can be offered to the customer as an alternative option. (This applies to vehicles with the sale code GXR only). ~Before 3rd quarter -2017. For the vehicles with the sales code GXX the Blade Key (immobilizer only & no transmitter) P/N 05134937AA can be offered to the customer as an alternative option.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the blade key (no immobilizer & no transmitter) P/N 05018689AA can be offered to the customer as an alternative option. (This applies to vehicles with the sale code GXR only). ~Before 3rd quarter -2017. For the vehicles with the sales code GXX the Blade Key (immobilizer only & no transmitter) P/N 05134937AA can be offered to the customer as an alternative option.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the blade key (no immobilizer & no transmitter) P/N 05018689AA can be offered to the customer as an alternative option. (This applies to vehicles with the sale code GXR only). ~ For the vehicles with the sales code GXX the Blade Key (immobilizer only & no transmitter) P/N 05134937AA can be offered to the customer as an alternative option."

*KB UPDATED 5/14/2012. *JS

*TT

*KB

*TT

*TT

*AK

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*NJ

*KB

*SC