2016 Dodge Dart TSBs

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

installed in the vehicle.

oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0335-00 - Crankshaft Position Sensor Circuit.** P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes: Enhancements to the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only). Engine oil temperature gauge calibration enhancement.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P1185 - General Pressure Sensor Correlation.** P0335 - Crankshaft Position Sensor Circuit. P050D - Cold Start Rough Idle. P0456 - Evap System Small Leak. P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. **In addition to the above DTCs, this software release also includes these enhancements/corrections: A ?Clunk feeling" when depressing the gas pedal after a coasting maneuver when Decel Fuel Shut Off (DFSO) is enabled and is exiting during pedal tip-in.** False reading that the engine is overheating based on the engine oil temp gauge read out. Improved ambient temperature sensor diagnostics during sunload. Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A for an exchange or 05064993A for a new part replacement. Prior to replacing parts, Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~ ~______________________________________~ Contact Us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. DO NOT email regarding repair procedures unrelated to this Tech Tip or part order inquires. Please include the Part Number (s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

These vehicles may exhibit a vibration in the engine.

MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com

These vehicles may exhibit a vibration in the engine.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0133 - O2 Sensor 1/1 Slow Response. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include an engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0133 - O2 Sensor 1/1 Slow Response. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include an engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

These vehicles may exhibit a vibration in the engine.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0335-00 - Crankshaft Position Sensor Circuit.** P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes: Enhancements to the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only). Engine oil temperature gauge calibration enhancement.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P1185 - General Pressure Sensor Correlation.** P0335 - Crankshaft Position Sensor Circuit. P050D - Cold Start Rough Idle. P0456 - Evap System Small Leak. P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. **In addition to the above DTCs, this software release also includes these enhancements/corrections: A ?Clunk feeling" when depressing the gas pedal after a coasting maneuver when Decel Fuel Shut Off (DFSO) is enabled and is exiting during pedal tip-in.** False reading that the engine is overheating based on the engine oil temp gauge read out. Improved ambient temperature sensor diagnostics during sunload. Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0456 - EVAP System Small Leak. ? P2610 - PCM Internal Engine Off Timer Performance. ? P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes: ? This software release includes improving the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. ? Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only). ? Engine oil temperature gauge calibration enhancement.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0456 - Evap System Small Leak. ? P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). ? P2610 - PCM Internal Engine Off Timer Performance. ? P1607 - PCM Internal Shutdown Timer Rationality. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include: ? Improved ambient temperature sensor diagnostics during sunload. ? Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. ? Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition. NOTE: Reprogram the PCM if P0335 is present along with engine misfire DTCs.

Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump sensation felt during moderate to heavy acceleration over 3,500 RPM. ? P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)). 2014 Dart ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylind

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0456 - EVAP System Small Leak. ? P2610 - PCM Internal Engine Off Timer Performance. ? P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes an engine oil temperature gauge calibration enhancement.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0133 - O2 Sensor 1/1 Slow Response. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include an engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

Module (TCM) with the latest available software. Customers may experience a delayed up-shift. The condition may be noticed when cornering with a light accelerator pedal and speeds up to 25 MPH (40 KPH) causing high engine rpm.

Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0615XX)). 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0335-00 - Crankshaft Position Sensor Circuit.** P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes: Enhancements to the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only). Engine oil temperature gauge calibration enhancement.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P1185 - General Pressure Sensor Correlation.** P0335 - Crankshaft Position Sensor Circuit. P050D - Cold Start Rough Idle. P0456 - Evap System Small Leak. P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. **In addition to the above DTCs, this software release also includes these enhancements/corrections: A ?Clunk feeling" when depressing the gas pedal after a coasting maneuver when Decel Fuel Shut Off (DFSO) is enabled and is exiting during pedal tip-in.** False reading that the engine is overheating based on the engine oil temp gauge read out. Improved ambient temperature sensor diagnostics during sunload. Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.

These vehicles may exhibit a vibration in the engine.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com

contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent, corroded, or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Malcolm Whitehouse (OCM Module - PF,KL, or UF Vehicles ONLY)@248-462-4703 or Malcolm.Whitehouse@fcagroup.com.~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com~

contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P050D - Cold Start Rough Idle.** P0456 - Evap System Small Leak. P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include: Improved ambient temperature sensor diagnostics during sunload. Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DTCS SET IN THE PCM MEMORY: **P1066 - CYLINDER 1 OIL SUPPLY SOLENOID VALVE SWITCH OFF TIME OUT OF RANGE. P1068 - CYLINDER 2 OIL SUPPLY SOLENOID VALVE SWITCH OFF TIME OUT OF RANGE. P106A - CYLINDER 3 OIL SUPPLY SOLENOID VALVE SWITCH OFF TIME OUT OF RANGE. P106C - CYLINDER 4 OIL SUPPLY SOLENOID VALVE SWITCH OFF TIME OUT OF RANGE.** P1185 - GENERAL PRESSURE SENSOR CORRELATION. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P050D - COLD START ROUGH IDLE. P0456 - EVAP SYSTEM SMALL LEAK. P0133 - O2 SENSOR 1/1 SLOW RESPONSE (ADDITIONAL ENHANCEMENTS). P2610 - PCM INTERNAL ENGINE OFF TIMER PERFORMANCE. P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. IN ADDITION TO THE ABOVE DTCS, THIS SOFTWARE RELEASE ALSO INCLUDES THE FOLLOWING: A CLUNK FEELING"" WHEN DEPRESSING THE GAS PEDAL AFTER A COASTING MANEUVER WHEN DECEL FUEL SHUT OFF (DFSO) IS ENABLED AND IS EXITING DURING PEDAL TIP-IN. FALSE READING THAT THE ENGINE IS OVERHEATING BASED ON THE ENGINE OIL TEMP GAUGE READ OUT. IMPROVED AMBIENT TEMPERATURE SENSOR DIAGNOSTICS DURING SUNLOAD. DISABLE MISFIRE MONITOR WHEN P0335 (CRANKSHAFT POSITION SENSOR CIRCUIT) IS PRESENT. ENGINE OIL TEMPERATURE GAUGE LEVEL RECALIBRATION TO AVOID THE MISPERCEPTION OF AN ENGINE OVERHEATING CONDITION."

MODULE (TCM) WITH THE LATEST AVAILABLE SOFTWARE. CUSTOMERS MAY EXPERIENCE ONE OR ALL OF THE FOLLOWING: **ENGINE REVVING BEFORE UP-SHIFTING AT LOW TO MODERATE SPEEDS. (2.4L ONLY) DELAYED SHIFTING / NOT WANTING TO SHIFT UNTIL ABOUT 3500 RPM, WHEN DRIVING STRAIGHT. (2.4L ONLY) SHUDDERING OR BUMPS WHILE MOVING AND STEPPING ON THE ACCELERATOR PEDAL. (2.4L ONLY)** A DELAYED UP-SHIFT. THIS CONDITION MAY BE NOTICED WHEN CORNERING WITH A LIGHT ACCELERATION AND SPEEDS UP TO 40 KPH (25 MPH) CAUSING HIGH ENGINE RPM."

THESE VEHICLES MAY EXHIBIT A VIBRATION IN THE ENGINE."

DELAYED UP-SHIFT CAUSING HIGH ENGINE RPM *CN

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

front door glass run applique and window glass. The customer may describe that the left front door glass run applique has a wrinkled appearance or that the window does not fully close due to applique seal entrapment.

front door glass run applique and window glass. The customer may describe that the left front door glass run applique has a wrinkled appearance or that the window does not fully close due to applique seal entrapment.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

front door glass run applique and window glass. The customer may describe that the left front door glass run applique has a wrinkled appearance or that the window does not fully close due to applique seal entrapment.

If vehicle is has the silver OE shift knob, you will also need to order a new upper (68157603A*) and lower (68087185A*) shifter knob pieces. You can find instructions for replacing the cable under LOP 21-75-31-01.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

Before replacing the AC compressor for noise, leaks , or for an inop condition:~ After these questions have been answered please call one of the individuals below.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below:~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

The customer may describe poor rear speaker performance due to an incorrect rear shelf panel installed in the vehicle.

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.

Cluster Warning Chime Goes Off

Cluster Warning Chime Goes Off

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

B)

Compressor or Condenser, do not stow any AC lines in proximity to any heat sources, or sharp edges.~ After the vehicle is reassembled, confirm that all AC lines are in correct design position and not in contact with any heat sources, or sharp edges.